TPS3837L30DBVR
Product Specifications
TPS3837L30DBVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS3837L30DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS3837L30DBVR nano power supervisor with an active high reset
The TPS3837L30DBVR is the active high member of the TPS383x nano power family. It watches a 3 V rail against a 2.64 V threshold and drives its output high while the rail is below that level, then releases it after a delay selected by the CT pin. Everything else about the part matches its siblings: 220 nA typical supply current, a 1.6 V to 6 V supply range, a manual reset input and a 5 pin SOT-23 body.
The active high output is not a detail. A processor whose reset pin is active low cannot be driven by this part directly, and a peripheral that is enabled by a high level, such as a load switch, a level translator or a second regulator, is exactly what this member is for. Choosing between the TPS3836 and the TPS3837 is therefore a decision about the polarity of the net, not about the supply.
Key parameters taken from the TPS383x document
| Monitored rail | 3 V option with a 2.64 V threshold, printed as 2.56 V minimum and 2.69 V maximum over minus 40 to plus 85 degrees |
| Supply range | 1.6 V to 6 V on the supply pin |
| Supply current | 220 nA typical, the same silicon as the active low member |
| Reset delay | 5 to 15 milliseconds with CT at ground, 100 to 300 milliseconds with CT at the supply |
| Reset output | Push pull active high, which rises with the rail and pulls low while the rail is below the threshold |
| Output drive | High level at 0.8 times the supply sourcing 2 mA at 3.3 V, low level below 0.4 V sinking 1 mA at 1.8 V |
| Hysteresis at the supply pin | 30 mV for a threshold between 1.7 V and 2.5 V and 40 mV for a threshold between 3.5 V and 5 V |
| Manual reset | Input with an internal pull up, logic low at 0.3 times the supply, tied to the supply when unused |
| Response | 10 microseconds typical and 50 microseconds maximum from the supply to the output, and 0.3 microseconds from the manual reset input |
| Reset at power up | Output state valid from a 1.1 V supply |
| Body | 5 pin SOT-23 DBV |
| Lifecycle | The plain TPS3837L30DBVR row is marked not recommended for new builds in the revision attached here, while the .A row of the same body is active |
The lifecycle row is the first thing to read on this order code. In the revision attached to this page the plain TPS3837L30DBVR row carries a not recommended status while the same body with the .A option is active, and the tube option is marked obsolete. A production order therefore has to name the option rather than assume that the shortest string is the current one, and a customer who has been buying the plain row for years should be told before the next build rather than after it.
Where the numbers matter in a real build
An active high reset is most often used to hold a second device off while the main rail is not valid. A level translator, a radio module or a secondary regulator that must not draw current before the processor is ready is enabled by this output, and the delay after the rail is good becomes the point at which that device is allowed to start. Setting the CT pin to ground gives a 5 to 15 millisecond window for a device that starts quickly, and tying it to the supply gives up to 300 milliseconds for a device that needs its own supply to settle first.
The 220 nA supply current matters here for a different reason than on the active low member. Where the supervisor enables a load switch, the supervisor itself stays alive in the state where everything else is off, so its current is the entire standby load of that branch. A part that draws 220 nA can be left permanently connected to the cell, and a part that draws 15 microamp needs its own switch and a second supervisory problem.
The push pull output is quoted with a high level of 0.8 times the supply at 2 mA and a low level below 0.4 V at 1 mA. That is enough to drive the enable pin of a regulator or a logic gate, and it is not enough to drive a relay coil or a long cable without a buffer. Where the load is inductive or the net is long, the output should drive a transistor rather than the load itself, because a nano power comparator has no protection against an inductive kick.
What to check before a purchase order is released
- The life cycle status of the exact option, because the plain row of this string is not recommended for new builds while the .A row is active.
- The output polarity against the net it drives, since an active high output on an active low reset pin holds the processor in reset forever.
- The CT pin setting, which selects between the two fixed delays and must not be left floating.
- The threshold letter, because L30 at 2.64 V and H30 at 2.79 V share a body and a footprint.
- The manual reset pin, which has to be tied to the supply on a board with no button.
Which projects this part fits
Boards that sequence a radio module, a level translator or a second regulator behind the main rail are the first case. Portable instruments that must keep an expansion connector unpowered until the processor is running are the second, and any product where the enable polarity is high by the nature of the device being enabled is the third.
Questions that come up before a purchase order is released
Can this part replace the active low member?
Only if the net it drives expects a high level to assert. The two members are otherwise identical, so the substitution is a wiring decision and not a component decision.
Does the output go low when the supply collapses?
Yes, but below the power up reset level the state is not guaranteed, which is why the output is described as valid from a 1.1 V supply and why a pull down on a critical enable pin is worth fitting.
Is the delay the same on both members?
Yes, the same CT pin and the same windows, so the two parts can be swapped on a prototype without changing the timing.
How SUPERB handles this line
A part in this position is usually found on a board that has been in production for years, and the plain row of the order code is the one that goes end of life first. Our obsolescence management note covers how a last time buy is sized, and the pin to pin cross reference is where the .A option is checked against the plain row before a change is proposed. For a build that needs parts this month, the date code note explains what we can and cannot accept on a reel.