TPS3820-33QDBVRQ1
Product Specifications
TPS3820-33QDBVRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS3820-33QDBVRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS3820-33QDBVRQ1 3.3 V supply monitor with a 25 millisecond reset and a watchdog
The TPS3820-33QDBVRQ1 watches a 3.3 V rail against a 2.93 V threshold, holds the processor in reset for 25 milliseconds after the rail is good, and then keeps watch on a software heartbeat. If the heartbeat stops, the watchdog asserts the same reset line. The whole part sits in a 5 pin SOT-23 and draws 15 microamp typical, so it is the shape of supervisor that ends up on almost every processor board that has no room for a separate watchdog.
The Q1 suffix in the catalogue string marks the automotive qualified version. The document attached to this page is the industrial TPS382x family revision, which is where the thresholds, the timings and the watchdog behaviour come from, and the automotive order codes carry their own qualification document and their own packaging rows.
Key parameters taken from the TPS382x document
| Monitored rail | 3.3 V option, nominal threshold 2.93 V, with 2.5 V, 3 V and 5 V members in the same family |
| Reset delay | 25 milliseconds fixed on the TPS3820 members, against 200 milliseconds on the TPS3823, TPS3824 and TPS3828 members |
| Watchdog timeout | 200 milliseconds on this member, against 1.6 seconds on the TPS3823 and its siblings |
| Reset output | Push pull active low on this member, with an active high variant and an open drain variant elsewhere in the family |
| Manual reset | MR input fitted, with an internal pull up of about 90 kilohm |
| Watchdog input | WDI driven by a falling edge, with a floating pin generating internal pulses so that an unconnected watchdog never fires |
| Supply current | 15 microamp typical and 25 microamp maximum with the watchdog, the manual reset and the outputs unconnected |
| Input current | 190 microamp maximum average on WDI high and 60 microamp on WDI low, which is the price of a watchdog input that is driven rather than sampled |
| Power up | Reset is asserted once the supply passes 1.1 V, so the output is defined long before the rail is useful |
| Body | 5 pin SOT-23 DBV, the only body printed for the family |
| Reel and marking | 3000 pieces on a large reel on the industrial row, body marking printed per threshold option in the addendum |
| Temperature | Minus 40 to plus 85 degrees C, with the TPS3823A-33 member specified to 125 degrees |
Two rows in the vendor addendum need reading before a string is copied onto a purchase order. The industrial rows for this family are printed with 3000 piece large reels and one small reel row marked as not recommended for new builds, and the automotive rows are not printed in this document at all. That is not a defect, it is the vendor keeping the automotive family in its own file, but it means the Q1 string on this page has to be confirmed against the automotive addendum rather than against the table attached here.
Where the numbers matter in a real build
The 25 millisecond delay is short for a processor that runs a boot loader. It is long enough for a regulator to finish its own soft start and for the clock to settle, and short enough that a brownout reset is over before a user notices it. The TPS3823 members in the same family stretch the same delay to 200 milliseconds for processors that need more settling time, and the choice between them is a choice about the software rather than about the supply.
The watchdog timeout of 200 milliseconds is the row that decides whether this part fits. A processor that toggles its heartbeat every 50 milliseconds is comfortable, one that toggles it every 500 milliseconds is reset on every cycle, and one that toggles it from a task that can be blocked for 300 milliseconds under load is reset under load. In practice the timeout has to be at least four times the longest legal gap between heartbeats, and on a board that cannot guarantee that gap the 1.6 second member is the one to order.
The 15 microamp typical supply current and the 25 microamp maximum are close together, which is unusual for a monitoring part and useful when the number goes into a power budget. The input current on WDI is a different order of magnitude, up to 190 microamp average while the pin is held high, because the internal watchdog circuit pulls against the driving pin. A processor that drives WDI through a series resistor large enough to protect the pin will find the high level degraded, and the vendor intends the pin to be driven directly.
What to check before a purchase order is released
- The watchdog timeout, because 200 milliseconds on this member and 1.6 seconds on the TPS3823 members look identical on a board drawing.
- The reset polarity and type, since the family prints push pull active low, push pull active high and open drain outputs in the same 5 pin body.
- The automotive suffix, which is not printed in the industrial addendum and has to be confirmed against the automotive document.
- The WDI pin when the watchdog is unused, because a floating pin is ignored by the part and a pin tied high or low is not.
- The MR pin when there is no reset button, since it carries an internal pull up and only needs an external capacitor for a slow release.
Which projects this part fits
Digital signal processor boards, microcontroller units and processor modules that need a heartbeat watch as well as a supply watch are the main case, and the automotive variant puts the same behaviour on body controllers, dashboard modules and motor control boards. Instrument panels that must recover by themselves after a supply dip are the second case, and any board where the software team wants a recovery path without writing a watchdog into the application is the third.
Questions that come up before a purchase order is released
Does the watchdog fire during a debug session?
Yes, unless the debugger keeps toggling the pin or the WDI pin is left floating, which the vendor intends the part to ignore.
Is the reset output strong enough to drive a second device?
The push pull output drives a few milliamps, which is enough for one or two reset inputs and not enough for a long bus with several loads, where a buffer or an open drain variant with a pull up is the better arrangement.
Can the threshold be changed on the board?
No. The threshold comes from an internal divider and the part is ordered by rail voltage, so a 3.3 V board cannot use the 5 V member even with an external divider on the supply pin.
How SUPERB handles this line
Watchdog supervisors in the 5 pin SOT-23 are consumed at a steady rate on any board that runs a processor, so they appear on shortage lists as soon as a factory moves a line. Our BOM shortage recovery describes how a short line is covered without changing the board, and the date code note covers what a reel has to prove before it goes onto an automotive line. When the automotive row cannot be found at a sensible lead time, the pin to pin cross reference is where an alternative is checked first.