TPS3801K33DCKR
Product Specifications
TPS3801K33DCKR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS3801K33DCKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS3801K33DCKR: 3.3 V supply supervisor with a 200 ms reset delay in a 5 pin SC70
TPS3801K33DCKR is a supply voltage supervisor that holds a processor in reset until the 3.3 V rail has been above 2.93 V long enough for the clock to be stable in a SC70 body of 5 pins. It monitors a 3.3 V rail against a 2.93 V threshold with 40 mV of hysteresis, holds the open drain reset output low for 200 ms after the rail returns, and adds a manual reset input. The threshold window is 2.87 V to 2.99 V over temperature, supply current is 13 uA typical, and the 5 pin SC70 body needs a 0.1 uF bypass capacitor at the supply pin.
Order code and package
| TPS3801K33DCKR | 5 pin SC70 (DCK), 3000 pieces on a large reel, marking NWA, moisture level 1 unlimited |
| Threshold | 2.93 V nominal for the K33 code, with a 2.87 V minimum and 2.99 V maximum over minus 40 C to plus 85 C |
| Reset delay | 200 ms for the TPS3801 family, against 100 ms on the TPS3800 and 400 ms on the TPS3802 |
| Manual reset | present on every member except the TPS3801-01, which is the adjustable version |
| Temperature range | minus 40 C to plus 85 C free air, which is narrower than a power management part |
Electrical parameters that decide the application
| Supply voltage | 1.6 V to 6 V, with the reset output defined from 1.1 V as the power up reset voltage |
| Threshold window | 2.87 V minimum, 2.93 V typical and 2.99 V maximum, an accuracy of 2 to 2.5 per cent over temperature |
| Hysteresis | 40 mV on the 3.3 V code, so the release point is above the trip point by that margin |
| Reset delay | 200 ms from the moment the monitored rail passes the threshold |
| Supply current | 13 uA typical and 18 uA maximum at 4 V with the reset output unconnected |
| Output type | open drain, needing a pull up resistor, sinking 2 mA at 0.4 V |
| Manual reset input | active low, with 25 nA of input current and an internal pull up |
| Power up behaviour | the output is guaranteed to be low from 1.1 V of supply, so the processor is held before its own logic is valid |
| Bypass capacitor | 0.1 uF ceramic at the supply pin, which the vendor states as a condition for threshold stability |
| Body | 5 pins, supply, ground, sense, reset and manual reset, nothing else required |
The threshold codes in the same family
| E18 | 1.71 V threshold for a 1.8 V rail, with 25 mV of hysteresis |
| J25 | 2.25 V for a 2.5 V rail, 30 mV of hysteresis |
| G27 | 2.50 V for a 2.7 V nominal rail, 35 mV of hysteresis |
| L30 | 2.64 V for a 3.0 V rail, 35 mV |
| K33 | 2.93 V for a 3.3 V rail, 40 mV, the code on this page |
| I50 and T50 | 4.55 V and 4.00 V for 5 V rails, with 60 mV of hysteresis on the I50 |
| 01 suffix | adjustable, with a 1.14 V reference on the sense pin, and no manual reset input |
Points to check before this part goes on a BOM
The threshold of 2.93 V for a 3.3 V rail is a fall of 11 per cent before the reset asserts, which is looser than the 5 per cent that most logic is specified to. That is deliberate: a supervisor that trips at 3.14 V flags every load step as a failure. The correct reading is that the reset is a last resort protection, and the rail regulation is what keeps the processor running; the supervisor only catches a supply that has genuinely collapsed.
The 200 ms delay is measured from the moment the monitored rail crosses the threshold on the way up. It is the time the processor gets to stabilise its oscillator and its internal state before the reset is released. A 200 ms delay is generous for most microcontrollers and short for a module with a crystal that takes longer, and the family offers 100 and 400 ms members for exactly that reason.
The supply current figure in the vendor table is printed with a unit column that reads milliamps, while the numbers, 9 to 18, are microamps by every curve in the same document and by the behaviour of the part. The practical reading is microamps, and a budget that assumes milliamps for this supervisor is over estimating its drain by a factor of a thousand.
The power up reset voltage of 1.1 V is a guarantee that matters more than it appears. Below 1.1 V the output is not defined, so a processor whose core rail comes up before its input output rail can briefly see a released reset before the supervisor has any authority. On a board with two rails, the supervisor should be powered from the rail that comes up first, which is usually the 3.3 V standby rail.
The manual reset input has an internal pull up and draws 25 nA, so a push button to ground is all that is needed. It is also a convenient place to hang a test point for a production fixture that wants to hold the processor in reset while it programs flash. The input has no debounce of its own beyond the 200 ms reset delay, so a noisy button produces a reset that is at least 200 ms long.
The 0.1 uF bypass capacitor at the supply pin is stated as a condition for threshold stability, not as a recommendation. A supervisor compares a divided version of the supply against an internal reference, and any noise on the supply pin moves that comparison. On a board with a switching regulator nearby, a missing capacitor produces resets that appear random and disappear when the load changes.
The open drain output sinks 2 mA at 0.4 V, which is enough for a pull up to 3.3 V through 1.5 kOhm. A common mistake is to pull the reset up to a 5 V rail on a 3.3 V processor, which works electrically but gives the processor a 5 V signal on an input that is not rated for it. The pull up belongs on the rail that the processor uses.
Where this order code fits
It holds processors, FPGAs and memory controllers in reset in industrial controllers, metering, appliance boards and automotive body modules, where a 3.3 V rail can dip during a load dump or a connector event and the processor must not run through it. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the MCU Cross Reference page.
Questions buyers ask
At what voltage does the reset assert? At 2.93 V nominal on a falling rail, with a 2.87 V to 2.99 V window over temperature. The 40 mV of hysteresis keeps it from chattering at the trip point.
How long is the reset held after the rail recovers? 200 ms on the TPS3801 family. The TPS3800 holds 100 ms and the TPS3802 holds 400 ms, all in the same 5 pin body.
Is the output push pull or open drain? Open drain on the reset output, so a pull up resistor to the processor rail is required. It sinks 2 mA at 0.4 V.
Does it have a manual reset input? Yes, active low with an internal pull up, on every member except the adjustable TPS3801-01.
What supply current does it draw? 13 uA typical and 18 uA maximum. The unit column in the vendor table prints milliamps, which is a printing error rather than a real figure.
Can it supervise a 5 V rail instead? Yes, with the I50 or T50 threshold codes in the same family. The body and the pinout do not change, only the internal divider.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Supplier Quality Audit page sets out the checks that keep a substitute from failing on the bench.