TPS3780DDBVR
Product Specifications
TPS3780DDBVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS3780DDBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS3780DDBVR dual channel voltage detector with open drain outputs
The TPS3780DDBVR is a two channel voltage detector from Texas Instruments. Each channel compares its sense input against a factory set threshold and pulls its output low when the monitored voltage falls below it, which is a simpler job than a supervisor: there is no reset delay, no watchdog and no manual reset input. The part exists for the cases where a board needs a flag rather than a reset, and it draws 2 microamp while doing it.
The D in the order code is the hysteresis option, 1 per cent on this member, and the family carries 0.5, 1, 5 and 10 per cent in the same body. The 80 in the family name is the open drain output, while the TPS3779 members of the same document are push pull. Both halves of the family share the adjustable sense inputs, the 1.5 V to 6.5 V supply range and the same pinout.
Key parameters taken from the TPS3779 and TPS3780 document
| Channels | Two independent detectors, each with its own sense input and its own output |
| Supply range | 1.5 V to 6.5 V, which covers a single cell product and a 5 V rail alike |
| Threshold accuracy | 1.0 per cent on the sense threshold and on the hysteresis, according to the features table |
| Hysteresis options | 0.5, 1, 5 and 10 per cent, selected by the letter in the order code, D being 1 per cent |
| Sense inputs | Adjustable down to 1.2 V with two external resistors per channel |
| Quiescent current | 2 microamp typical, the reason the part appears in battery products |
| Output | Open drain on this member, so each output needs a pull up and can be pulled to a rail other than the supply, up to 6.5 V |
| Output current | Low level 0.25 V at 2 mA on a 2.7 V supply, and 0.3 V at 3.2 mA on 4.5 V, which is enough for a logic input and not for a relay |
| Temperature | Minus 40 to plus 125 degrees C |
| Packages | SOT-23 6 pin in the DBV body, and a 1.45 by 1.0 millimetre SON in the DRY body |
| Order rows | DDBVR is the DBV body on a 3000 piece large reel, DDBVT is the same body on a 250 piece small reel, and the DDRY rows are the SON body at 5000 and 250 pieces |
The absence of a reset delay is the row that decides whether this part is right. A detector flags a rail, a supervisor holds a processor in reset for a defined time after the rail recovers. A board that needs the processor to stay in reset while an oscillator settles cannot get that from this family, no matter how the outputs are wired.
Where the numbers matter in a real build
The hysteresis letter is the first decision, and it is not cosmetic. A 1 per cent hysteresis on a 3.3 V threshold is 33 mV, which is wide enough to reject the ripple of a switching regulator and narrow enough that a sagging rail is still reported. A 10 per cent option is 330 mV, which will hide a rail that is genuinely out of regulation. Products with a noisy rail tend to need the wider option, and products that use the detector as a low battery warning need the narrow one.
The second number is the 2 microamp quiescent current, but only if the external divider is sized for it. A divider that draws 30 microamp to hold a stiff threshold defeats the purpose of the part. Sizing the divider at a few hundred nanoamp keeps the total budget honest, at the cost of a threshold that moves with the leakage of the sense pin and with board contamination, which is why the vendor publishes the input current as a separate row.
The third is the open drain output. Because the pull up can go to 6.5 V independently of the supply, the detector can run from a 1.8 V rail and still drive a 3.3 V logic input. The same property means the output cannot be left without a pull up, and a board that treats it as a push pull output will see a floating line that reads high on a bench and low in a cold cabinet.
What to check before a purchase order is released
- The output type against the rest of the board, because the TPS3779 member is push pull and the TPS3780 member is open drain.
- The hysteresis letter, since D is 1 per cent and A, B and C are 0.5, 5 and 10 per cent on the same footprint.
- The divider resistors on each channel, calculated from the threshold and the sense input current, not copied from a reference board.
- The pull up on each output, which has to suit the logic level of the device being driven rather than the supply of the detector.
- The reel size, because the DBV body ships 3000 on a large reel and 250 on a small reel, and a prototype line usually wants the small one.
- The temperature range against the cabinet, since 125 degrees C is genuine on this family and is one reason it is used in automotive sub assemblies.
Which projects this part fits
The vendor lists DSP, microcontroller and microprocessor applications, portable medical devices, building automation, set top boxes, solid state drives, computers, portable and battery powered products, and power supply sequencing. The sequencing case is the one that suits two channels best: a board with a main rail and a standby rail can use one channel to warn the processor and the other to enable a load switch, without any software involvement at all.
Questions that come up before a purchase order is released
Can the two channels be set to different thresholds?
Yes. Each channel has its own sense input and its own divider, so one can watch a 5 V rail and the other a 1.2 V rail in the same package.
Is a reset delay available on this family?
No. The outputs follow the sense inputs with a propagation delay of microseconds, so the part is a detector and not a supervisor.
What happens if a sense input is left floating?
An open sense input is undefined, so the output state is undefined. Unused channels should be tied to a known rail or to ground through a resistor rather than left open.
Does the part work below 1.5 V?
The supply range starts at 1.5 V and the outputs are not defined below it. A single cell product that discharges to 1.2 V needs a different family or a boost rail for the detector itself.
How SUPERB handles this line
Detectors like this one are usually bought in small quantities alongside the rest of a board, so the practical question is availability of a 250 piece carrier rather than a full 3000 piece reel. Our power management cross reference lists the detector and supervisor families that map onto each other, and the drop in replacement checklist covers the electrical checks that decide whether a substitute is genuinely equivalent. Where a board is running out of a part that is no longer stocked, the obsolete part cross reference hub is the first stop.