TPS3619-33DGKR
Product Specifications
TPS3619-33DGKR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS3619-33DGKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS3619-33DGKR backup battery supervisor for RAM retention on a 3.3 V rail
The TPS3619-33DGKR keeps a small static memory alive when the main supply goes away. It watches a 3.3 V rail, holds the processor in reset while that rail is bad, and switches the memory supply over to a backup cell when the rail falls below its threshold. The switch back is automatic when the rail returns, and the cell is isolated while the main supply is present so it is not drained by the working circuit.
The part is one of a pair of families that differ in one feature. The TPS3619 carries a battery freshness seal, a mode that disconnects the cell until the product is first powered, which stops a stored unit from arriving with a flat battery. The TPS3620 does not. Both are pin compatible with the MAX819, MAX703 and MAX704 supervisors, which is why they turn up as drop in parts on older boards as well as on new ones.
Key parameters taken from the TPS3619 document
| Monitored rail | 3.3 V nominal, negative going threshold 2.88 V minimum, 2.93 V typical, 3.00 V maximum |
| Reset delay | 100 ms fixed after the rail rises above the threshold |
| Supply current | 40 microamp maximum from VDD in normal operation |
| Backup current | 100 nanoamp maximum from the cell in backup mode, which is the figure that decides cell life |
| Cell voltage | The backup cell may sit above VDD, which is what allows a 3.6 V cell on a 3.3 V rail |
| Switchover | Below 1.6 V on VDD the output switches to the cell regardless of the cell voltage, so the memory is not left floating |
| On resistance | 0.6 to 1 ohm from VDD to the memory supply, 8 to 15 ohm from the cell, which sets the drop the memory sees |
| Power fail input | PFI compared against 1.15 V to 1.17 V, with an open drain PFO output for a low battery warning |
| Freshness seal | Fitted on this family, and it is the feature that separates it from the TPS3620 |
| Manual reset | MR pin, active low |
| Temperature | Minus 40 C to 85 C |
| Package | VSSOP-8, 2500 pieces on a large reel, moisture level 1, marking AFL |
The 100 nanoamp backup figure is the one to work from. A 200 milliamp hour coin cell at that drain would last decades in theory, and in practice the cell's own self discharge and the memory's standby current are far larger. The supervisor's job is to not be the limiting factor.
Where the numbers matter in a real build
The switchover path is the first thing to calculate. At 8 to 15 ohm from the cell to the memory supply, a memory that draws 7.5 mA in backup mode drops 60 mV to 110 mV, which is fine for a 3 V cell feeding a 2.7 V memory but not for a 3 V cell feeding a 3 V part. The document gives both on resistance figures with their test currents, and the drop has to be checked against the memory's minimum retention voltage.
The second point is the threshold window. At 2.88 V to 3.00 V, a 3.3 V rail at minus 5 per cent is 3.135 V, comfortably above, and a rail that sags to 2.9 V may switch on one part and not on another. A board that relies on a clean switchover point needs the rail to fall fast, not to hover.
The third is the freshness seal. On a product that is built, stored and shipped, the seal keeps the cell from being drained by the supervisor while the unit sits in a warehouse. The seal is released on the first power up, and a product that is powered in test and then stored for a year will start that storage with the seal already open.
What to check before a purchase order is released
- The memory retention voltage against the cell voltage minus the drop across the 8 to 15 ohm switch path.
- Whether the board needs the freshness seal, since the TPS3620 is the same silicon without it.
- The pin compatibility claim against the original MAX part, because pin compatible does not always mean function compatible.
- The 100 ms reset delay against the processor start-up, which is short for a processor with a slow oscillator.
- The PFI divider, since the 1.15 V reference is lower than the 1.25 V used by most parts in this class.
- The cell type and its own self discharge, which usually dominates the 100 nanoamp figure.
Which projects this part fits
The vendor lists fax machines, set top boxes, voice mail systems, portable battery powered equipment, computer equipment, advanced modems, automotive systems, long time monitoring equipment and point of sale equipment. The common thread is a product that must remember its settings, a clock or a small buffer through a power cut, where a flash write on every change would wear out or take too long.
Questions that come up before a purchase order is released
Can a rechargeable cell be used?
Yes, provided the cell voltage stays inside the absolute maximum and the charging path is external. The part switches between the two sources, it does not charge the cell.
What happens if the cell is inserted the wrong way?
The cell pin has no reverse protection beyond the ratings in the document. A reversed cell is a board level fault, not something the supervisor corrects.
Why does the output switch below 1.6 V regardless of the cell?
That is the point where the internal control block can no longer trust the main rail, so it hands the memory to the cell. The behaviour protects the memory contents rather than the rail.
Is the reset output open drain or push-pull?
The reset output on this family is a push-pull driver with a defined level from VDD 1.1 V, which is what allows it to hold a processor in reset before the rails are up.
How SUPERB handles this line
Battery backup supervisors are bought with the memory, the cell holder and the crystal they protect, and they are usually the oldest part number on the board. Our power management cross reference puts this family beside the MAX parts it replaces, and the obsolete part cross reference hub is where we start when the original code is gone. Our supplier quality audit explains how a long life part is checked before it is released to a production line that will use it for years.