Contact Us

TPS3431SDRBR

Brand: Texas Instruments
Texas Instruments TPS3431SDRBR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS3431SDRBR — Power Management & Signal Chain | Superb Automation

TPS3431SDRBR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS3431SDRBR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS3431SDRBR: a programmable watchdog timer with an enable input and a pass through enable output in an eight pin 3 mm by 3 mm VSON

TPS3431SDRBR is a watchdog supervisor with a timeout set by a capacitor or by two logic pins, a 2.5 per cent accurate timer at 25 C, an active low open drain output and an enable path that restarts a load without removing power in a VSON (DRB) body of 8 pins. It runs from 1.8 V to 6.5 V, draws 10 microamp, sets the watchdog timeout to 1.6 s or 230 ms with the preset pins or anywhere in between with a capacitor from 100 pF to 1 microfarad, drives an active low open drain output when the processor stops petting it, and passes the enable signal through with a 200 microsecond delay. Packing is 3000 pieces with marking 431DD.

Order code and package

TPS3431SDRBRSON (DRB) body, 8 pins, 3.00 mm by 3.00 mm, 3000 pieces on a large reel, nickel palladium gold finish, moisture level 1 at 260 C with unlimited floor life, marking 431DD, active status in the addendum dated 9 November 2025
TPS3431SDRBRG4the same die and body with the G4 finish suffix, same reel, same marking, same 3000 piece packing
.A suffix rowsboth strings are repeated with an .A suffix in the addendum, and the finish and packing are read on the row
Automotive versionTPS3431-Q1 is listed as the qualified automotive variant of the same device, with its own document and its own addendum
Bodythe DRB outline is 3.00 mm by 3.00 mm with eight pins and an exposed pad, and the package drawing gives the land pattern
Evaluation boardTPS3431EVM-780 is the board the document names for bench work, which is the fastest way to see the timing before a board is built
Marking431DD on every row, so a reel is identified from the part marking when the label is unreadable

Electrical parameters that decide the application

Supply voltage1.8 V to 6.5 V on the supply pin, which covers a 1.8 V, 2.5 V, 3.3 V or 5 V logic rail without a second part
Quiescent current10 microamp typical, which is low enough for a supervisor that is always powered
Preset timeout1.6 s with the timing pin open and the select pin high, and 230 ms with a 10 kilohm resistor from the timing pin to the supply and the select pin high
Capacitor timeout77.4 milliseconds per nanofarad plus 55 milliseconds, so a 100 pF capacitor gives about 63 ms and a 1 microfarad capacitor gives about 77 s
Capacitor range100 pF to 1 microfarad, which is the range the device is tested over
Timer accuracy2.5 per cent typical at 25 C and 15 per cent over minus 40 C to 125 C, so the window has to allow for the temperature term
Disablethe watchdog is disabled by pulling the select pin low, or by leaving the timing pin open with the select pin low, which is the state a board uses during development
Outputan active low open drain output that pulls down on a watchdog fault and needs an external pull up to the logic rail
Enable pathan enable input internally pulled up, and an enable output that follows it after the reset delay, so a load can be restarted without the supply being removed
Enable timing200 microseconds from the enable input to the enable output, and the supply has to be above 1.8 V for 300 microseconds before the watchdog input is active
Watchdog inputa minimum pulse of 50 ns is enough to clear the timer, and the output responds 50 ns after a missed window
Temperatureminus 40 C to 125 C junction, which is the range the timer accuracy is specified over
Protectionthe output is open drain, so a short to a rail above the supply is limited by the external pull up rather than by the device

Family variants and how they differ

Preset and capacitortwo pins select between 1.6 s, 230 ms and off, and a capacitor on the timing pin overrides the presets with a continuous range
Select pinpulling the select pin low disables the watchdog, which is why a board should tie that pin rather than leave it floating during development
Enable and enable outputthe enable input is pulled up inside and the enable output follows it after the reset delay, so the same signal can restart a processor or a peripheral
AutomotiveTPS3431-Q1 carries the same function with automotive qualification and its own ordering strings
Bodyeight pins in a 3.00 mm by 3.00 mm VSON with an exposed pad, which is the thermal and the mechanical reference for the land pattern
Marking431DD is the same on the standard and the G4 rows, so the finish cannot be read from the marking

Points to check before this part goes on a BOM

The timer accuracy is 2.5 per cent at 25 C and 15 per cent over temperature. A watchdog window that is set close to the processor's own worst case service interval will trip in the cold or in the heat, so the window is usually set at twice the service interval rather than at it.

The capacitor timing is only as good as the capacitor. The document recommends a COG dielectric, because a part with a strong voltage and temperature coefficient will move the timeout by more than the 15 per cent the device allows.

The select pin has no default described. It is a logic input, so a board should tie it to a defined level rather than leave it floating, and the development state of disabled watchdog is a deliberate tie rather than an absence of one.

The enable output is the reason this part exists in some boards. It restarts a processor or a peripheral without removing the supply, which keeps the rest of the board alive while the stuck device is reset.

The open drain output needs a pull up. A board that leaves it floating has a watchdog that cannot signal, which is worse than no watchdog because the fault is silent.

What a watchdog actually protects against

A processor that hangs on a bus error, a stuck interrupt or a corrupted stack stops servicing the watchdog input, and the timeout pulls the output low. That output usually goes to a reset pin, so the processor restarts rather than sitting in a dead state until someone power cycles the product.

The enable path is for the case where the reset is not enough. A peripheral or a module that has latched up has to have its supply cycled, and the enable output does that from the same fault, with the 200 microsecond delay keeping the sequence orderly rather than simultaneous.

Where this order code fits

The part suits an asset tracker, an energy storage converter controller, an electricity meter, a motion detector, an IP camera or surgical equipment, where a processor has to be restarted if it stops responding. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

What timeout does it give with no external parts? 1.6 s with the timing pin open and the select pin high. A 10 kilohm resistor from the timing pin to the supply and the select pin high gives 230 ms instead.

How is a custom timeout set? A capacitor from the timing pin to ground, with the timeout in milliseconds equal to 77.4 times the capacitance in nanofarad plus 55 milliseconds, over the tested range of 100 pF to 1 microfarad.

Can the watchdog be turned off? Yes. Pulling the select pin low disables the timer, which is the state used during development. The pin is a logic input, so it has to be tied to a defined level rather than left open.

Does the output drive a reset pin directly? It is an open drain output that pulls low on a fault, so it needs a pull up to the logic rail. With that resistor it drives a reset pin, a processor input or the enable of a second device.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.