TPS274C65ASHWRHAR
Product Specifications
TPS274C65ASHWRHAR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS274C65ASHWRHAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS274C65ASHWRHAR quad high side switch, the W string on the same body
The TPS274C65ASHWRHAR is a four channel 72 milliohm high side switch from the same 6 mm by 6 mm VQFN family as the ASHRHAR row. The body, the pinout, the SPI interface and the diagnostics set are shared across the family. What the W adds is not described anywhere in the document as a separate function: the string appears in the orderable addendum next to the AS and ASH rows with the same package, the same 2500 piece reel, the same nickel palladium gold finish and the same moisture level, and the document prints no separate function row for it.
That absence is worth stating plainly rather than smoothing over. When a purchase order carries a string that the datasheet only lists in the addendum, the buyer has three honest options: ask the vendor for the order code note, ask for a sample and compare it against the documented ASH behaviour on the bench, or hold the build until the vendor confirms. What a buyer should not do is assume the W is a faster or a wider version, because nothing in the document supports that reading.
Key parameters taken from the TPS274C65 document
| Channels | Four, each with its own limit and diagnostics |
| On resistance | 72 milliohm per channel |
| Load range | 500 mA to 2 A DC per channel |
| Current limit | ASH row, 290 mA to 2.45 A adjustable |
| Inrush | Configurable period at a higher second limit |
| Interface | SPI control and digital current readback |
| Diagnostics | Open load on and off, short to supply, short to ground, thermal warning |
| Inductive clamp | Integrated, above 65 V in the reference circuit |
| Package | VQFN RHA, 40 pins, 6 mm by 6 mm, 0.5 mm pitch |
| Temperature | Minus 40 to plus 125 degrees in the orderable addendum |
| Carrier | 2500 pieces, large reel, moisture level 2 at 260 degrees, one year floor life |
| Finish | Nickel palladium gold, as listed for every row in the table |
| Documented difference | None printed for the W string beyond the orderable addendum row |
The rows above are read from the vendor document. The last row is the important one: it records what the document does not say, which is the only honest basis for a purchasing decision on this string.
Where the numbers matter in a real build
Because the electrical behaviour follows the ASH row, the practical questions are the same ones that apply to any four channel switch in this family. The current limit ceiling of 2.45 A leaves about 20 per cent headroom over a 2 A load, which is enough for tolerance and not enough for a solenoid that draws a cold current of three times its holding current, so the inrush period has to be set on the bench rather than from a rule of thumb.
The thermal path is the second constraint. Four channels at 2 A in a sealed box dissipate more than a watt in a 6 mm body, and the thermal information section ties the permissible dissipation to the copper area and the via pattern under the pad. A card that copies the reference board without the same copper pour will run hotter than the numbers in the document.
The diagnostics set is the third. A channel that is off and open reads zero current either because it is off or because the wire is broken, so the off state open load detection is what separates the two cases. That feature is set in registers and needs the SPI link to be alive, which means a card with a dead SPI bus loses its diagnostics even though the outputs keep switching.
- The vendor confirmation for the W string, because the document does not print a function row for it.
- The current limit level against the load tolerance, and the inrush level against the cold current of the load.
- The thermal copper area and via count against the conditions in the thermal section.
- The SPI pull-ups and the isolation barrier on the controller side.
- The integrated clamp against the stored energy of the load, which has a limit that is not a voltage rating.
- The moisture level record on the reel, since the body is a 0.5 mm pitch leadless package.
Which projects this part fits
The family is aimed at industrial control output modules that drive solenoids, lamps, contactors, valve pilots and resistive heaters, on cards where each output has to be diagnosable and each fault has to stay local. The same body appears on safety related modules where the diagnostics are read by a supervisor.
Questions that come up before a purchase order is released
Is the W a different silicon revision?
The document does not say so. It lists the string in the orderable addendum with the same package, reel, finish and moisture level as the other rows and prints no separate function row. The vendor is the only source that can confirm the difference.
Can an ASH part be used where the drawing calls for the W string?
Not on the strength of the datasheet alone. A substitution needs the vendor order code note plus a bench check of the limit behaviour, which is the same route a second source part takes.
Does the SPI interface change between rows?
The document prints one register map for the family and a pin function table that varies by version. The register behaviour is shared, the pin marking is not.
What is the practical limit for a 24 V solenoid?
The channel handles 2 A DC and the clamp handles the inductive kick. A solenoid that draws more than 2.45 A in steady state needs a different switch, since the limit would trip on a healthy load.
How SUPERB handles this line
An order code that exists only in an addendum is exactly the case where a purchase order needs a written confirmation with it, and that is the check we run before a reel is booked. Our pin to pin cross reference covers the family comparisons, how to verify a drop in replacement sets out the bench checks, and our supplier quality audit covers the paperwork we ask a channel to produce for a string like this.