Contact Us

TPS259814LRPWR

Brand: Texas Instruments
Texas Instruments TPS259814LRPWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS259814LRPWR — Power Management & Signal Chain | Superb Automation

TPS259814LRPWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS259814LRPWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS259814LRPWR 10 A eFuse with a 6 milliohm path and a circuit breaker

The TPS259814LRPWR is the highest current member of the TPS25981 family in a small body. It runs from 2.7 V to 16 V, holds a typical 6 milliohm path in a 2 mm by 2 mm ten pin QFN, and is rated for 10 A. Overcurrent is handled by active current limiting during start-up and by a circuit breaker in steady state, with an adjustable blanking timer between the two, and a fault keeps the path open until the input is cycled because this is the L member.

The 6 milliohm figure is what separates this family from the 28 and 34 milliohm parts on the same shelf. At 10 A the pass element dissipates about 0.6 W, which is the same heat as a 34 milliohm part at 4 A, so a 10 A rail can be protected inside the same 2 mm footprint. That is the reason these parts appear on 12 V rails in servers and on 5 V rails in high power hubs, where the older parts would need two devices in parallel.

Key parameters taken from the TPS25981 document

Input range2.7 V to 16 V operating, 20 V absolute maximum
On resistance6 milliohm typical for the integrated FET
Current rating10 A steady state
Current limit window1.5 A to 11 A, ten per cent accuracy above 5 A
Limit settingOne resistor on the ILM pin, printed as 6585 divided by the limit in amps
Measured limit points3.32 k for 1.98 A, 2.212 k for 2.98 A, 1.102 k for 5.98 A, 750 ohm for 8.73 A, 611 ohm for 10.78 A
Fast trip640 ns typical on a short, threshold tied to twice the set limit
Overvoltage lockoutAdjustable with a divider, 1.2 microsecond typical response
Blanking timerCapacitor on ITIMER discharged by a 2 microamp pull-down, peak loads up to twice the limit pass
Current monitorAnalog output on the ILM pin, ten per cent accuracy above 3 A
Digital pinsPower good and fault indication, both open drain
DischargeQuick output discharge path, 488 ohm typical, active while the part is disabled
PackageVQFN-HR RPW, ten pins, 2 mm by 2 mm, 0.45 mm pitch
Carrier3000 pieces on a large reel, moisture level 2 at 260 degrees with a one year floor life
Marking and grade2KXH, minus 40 to plus 125 degrees junction
RecognitionMET listing file E115731, UL 2367 compliance and IEC 62368-1 CB certification

Rows are read from the vendor document. The measured limit points are the useful part of the table, because the equation and the points do not agree to the last digit and a limit that a test measures should come from the points.

Where the numbers matter in a real build

The limit equation is 6585 divided by the limit in amps, and the five printed points sit close to it: 611 ohm gives 10.78 A, 750 ohm gives 8.73 A, 1.102 k gives 5.98 A, 2.212 k gives 2.98 A and 3.32 k gives 1.98 A. Note that the 611 ohm point is above the 10 A headline, which gives a rail with a legitimate 10 A load a margin before the breaker engages. The document also states that opening the ILM pin sets the limit to nearly zero and that shorting it to ground is detected as a fault, both of which are single point failures the part is tested against.

The two overcurrent mechanisms are worth separating. During start-up the part limits current, because a converter drawing its input capacitance through a 6 milliohm path would otherwise look like a short. In steady state the part breaks the circuit after the blanking timer expires, which removes the load rather than holding it at a reduced voltage. A board with a downstream converter that restarts cleanly on a power cycle prefers the breaker, while a board with a load that can ride through a dip prefers the current limit for its whole life. This member does the first in steady state and the second at start-up.

The blanking timer is set by one capacitor. A 2 microamp pull-down discharges it once the load passes the set limit, and it resets whenever the load falls back, so a peak of up to twice the limit passes for the time it takes to move the timer voltage by its threshold. That covers disk spin-up, motor start and capacitor charging after a hot plug, and it is also the reason a shorted load does not trip the part instantly: the fast trip path at 640 ns handles the hard short, while the timer handles the soft overload.

The quick output discharge is a small feature that saves a large argument. At 488 ohm typical the path removes the charge on the output capacitors while the part is disabled, so a hot plug into a board that was just unplugged does not present a live rail to the connector. Without it the output can float for seconds on a lightly loaded rail, and the next insertion sees a charged capacitor bank rather than a discharged one.

One difference inside this family is worth stating on the page rather than left in the table: the reverse blocking FET driver belongs to the 813 member, not to this one. A board that has to drive an external FET to block reverse current in the off state needs the other member, and the two share a body, a pin count and a reel size.

  • The L or A suffix, since a latched part and a retrying part look identical on the bench until a fault happens.
  • The limit resistor from the measured points, with one per cent tolerance to protect the ten per cent accuracy budget.
  • The timer capacitor against the longest legitimate peak in the product.
  • The copper under the QFN, because 0.6 W in a 2 mm body needs a real thermal path.
  • The reverse blocking requirement, because the FET driver is on a different member of the family.
  • The moisture level and the marking, which keep a level 2 reel traceable on the line.

Which projects this part fits

The vendor lists server and high performance computing rails, network interface cards, add on cards, datacenter equipment, storage and hot swap bays. A 10 A, 6 milliohm part in a 2 mm body fits a 12 V rail that feeds a fan tray, a drive bay or a line card, where the protection has to be close to the connector and the heat budget is tight.

Questions that come up before a purchase order is released

Does this part retry after a fault?

No. The L suffix is latch-off, so the path stays open until the input is cycled or the enable pin is toggled. The A member of the same family retries.

Can the part drive an external FET for reverse blocking?

Not on this member. The reverse blocking FET driver is on the 813 member. This part blocks reverse current through its own FET only while the path is on.

What sets the current limit?

One resistor on the ILM pin, with 6585 divided by the limit in amps as the vendor equation and five measured points printed next to it.

How fast does it react to a short?

The fast trip path responds in about 640 ns at twice the set limit. The blanking timer is a separate path for softer overloads.

Is the output discharged when the part is off?

Yes, through an internal path of about 488 ohm typical, which removes the charge on the output capacitors while the part is disabled.

How SUPERB handles this line

High current eFuses are usually bought together with the connector, the bulk capacitors and the sense resistors around them, and the family suffixes are easy to confuse. Our power management cross reference carries the mapping, our incoming inspection plan covers the marking and reel check, and our one stop BOM sourcing service covers the passives and the connector from the same shipment.