Contact Us

TPS259480LYWPR

Brand: Texas Instruments
Texas Instruments TPS259480LYWPR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS259480LYWPR — Power Management & Signal Chain | Superb Automation

TPS259480LYWPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS259480LYWPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS259480LYWPR 8 A eFuse in a 12 ball wafer scale package with latch-off response

The TPS259480LYWPR is an 8 A eFuse from the TPS25948 family, rated from 3.5 V to 23 V with a typical 12.2 milliohm path and a 28 V absolute maximum on the input. It comes in a 12 ball power wafer scale package of 2.43 mm by 1.71 mm, which is small enough to sit next to the connector it protects rather than at the other end of the board.

Two features separate this family from the older 5 V parts. The device can be powered from either IN or OUT, which matters in a system where the load side is alive before the input side, and the family also offers an external pin to disable reverse blocking so that power can flow backward in steady state for USB on the go or dual role operation. The L in this string is the latch-off member, so a fault keeps the path open until the input is cycled or the enable pin is toggled.

Key parameters taken from the TPS25948 document

Input range3.5 V to 23 V operating, 28 V absolute maximum
Supply sourceThe part can be powered from either the input or the output side
On resistance12.2 milliohm typical across the integrated back to back FETs
Current limit window1 A to 9 A, ten per cent accuracy above 3 A
Limit settingOne resistor on the ILM pin, printed as 4834 divided by the limit in amps
Published limit points2.43 k for 2.25 A, 1.62 k for 3.3 A, 604 ohm for 8.7 A
Fast tripUnder one microsecond typical on a short, threshold tied to twice the set limit
Overvoltage lockoutAdjustable with a divider, one microsecond typical response
Blanking timerCapacitor on ITIMER, so peak loads above the limit pass for a bounded time
Current monitorAnalog output on the ILM pin, six per cent typical accuracy above 3 A
Digital pinsSupply good output and a fault output on this member of the family
SurgeIEC 61000-4-5 tested to 28 V on the input without a series device
PackagePowerWCSP YWP, 12 balls, 2.43 mm by 1.71 mm, 0.5 mm pitch
Carrier3000 pieces on a large reel, moisture level 1 at 260 degrees with unlimited floor life
Marking and grade259480L, rated minus 40 to plus 125 degrees junction

The rows above are read from the vendor document. The moisture row is one of the practical differences against the older QFN parts: a level 1 body has no floor life limit, so a reel can sit on a shelf without a bake schedule.

Where the numbers matter in a real build

Twelve milliohms at 8 A is about 0.8 W in the pass path, and that number decides how much copper the package needs. The wafer scale body has its balls on a 0.5 mm pitch, so the thermal path goes through the balls into the board rather than through a lead frame, and a footprint with a solid ground pour under the part runs far cooler than one with a broken pour. On a 12 V, 8 A rail the difference between a good pour and a poor one is the difference between a part that stays under its thermal shutdown and one that cycles.

The current limit equation is printed as 4834 divided by the limit in amps, and the measured points sit close to it: 604 ohm is given as 8.7 A, 1.62 k as 3.3 A and 2.43 k as 2.25 A. The 604 ohm point is deliberately above the 8 A headline, which gives a board some headroom before the limit engages, and it is also the point to use when a load draws a legitimate 8 A continuously. A resistor tolerance of one per cent is normal here, because the limit accuracy is quoted at ten per cent above 3 A and a five per cent resistor eats half of that budget.

Being able to power the part from the output side is a feature that matters most in a battery backed product. If the load side holds charge while the input is removed, the part still has a supply for its internal logic and can hold the switch in the correct state rather than floating. In a dual role USB port the reverse blocking control pin lets the same connector both take power and deliver it, and the transition is managed by the pin rather than by an external switch.

The blanking timer works the same way as in the rest of the family. A capacitor on ITIMER holds the path closed while a peak above the limit passes, and the timer resets as soon as the load falls back. A disk drive that draws a surge on spin-up therefore runs without a trip, while a shorted cable trips after the interval. The capacitor has to be sized for the longest legitimate surge in the product, and the pass FET has to be checked for the energy it absorbs during that interval.

The latch-off behaviour is the part of this string that shapes service policy. Once the breaker opens, the part stays open until the input is cycled or the enable pin is toggled, so a product that has no way to cycle the input is a product that stays dead after a transient. That is the right outcome where a fault should be investigated, and the wrong outcome where a remote site needs the unit to recover on its own. The A member of the same family is the one to order for the second case.

  • The response suffix, L for latch-off in this string, because the marking and the reel do not show the behaviour.
  • The current limit resistor against the real continuous load, not against the peak on a bench.
  • The copper under the ball grid, since the thermal path runs through the balls.
  • The floor life advantage of the level 1 body, which removes a bake step from the line.
  • The supply source, input or output, because the part has to stay powered while the other side is at zero.
  • The reverse transfer requirement, since the pin that allows steady state reverse power belongs to a different member of the family.

Which projects this part fits

The vendor lists adapter and charger input protection, USB PD protection in phones, tablets, computers, notebooks, monitors and docks, server motherboards and add-on cards, enterprise storage, and power MUX and ORing. The 8 A rating with a 12 milliohm path suits a rail that feeds a 60 W to 100 W load from a barrel jack or a USB PD source, where the pass element has to be small and cool at the same time.

Questions that come up before a purchase order is released

What does the L suffix mean on this string?

It is the latch-off member. After a fault the path stays open until the input is cycled or the enable pin is toggled. The A member of the same family retries automatically.

Can the part pass power in both directions?

In steady state yes, but only on the members that carry the reverse blocking control pin. This member keeps reverse blocking active, so the path blocks from output back to input.

Does the part need a supply on the input to work?

No. It can be powered from either side, which is why it is used where the load holds charge or where the port can act as a source.

What is the difference against the QFN parts in the same family line?

This is a different family with a 12.2 milliohm path and an 8 A rating, in a wafer scale body with a level 1 moisture rating. The QFN families carry different current ranges and different pin functions.

Is the reel size fixed?

The published row is 3000 pieces on a large reel. A prototype quantity has to come from a cut reel or from a distributor stock lot.

How SUPERB handles this line

Wafer scale parts are where a small buying error becomes a line stop, because a 12 ball body has no room for a hand rework and a wrong suffix has no visible difference. Our power management cross reference maps the replacements, our pin to pin cross reference lists the checks a substitute has to pass, and our date code management keeps a level 1 reel and a level 3 reel from being mixed on the same line.