Contact Us

TPS25730SRSMR

Brand: Texas Instruments
Texas Instruments TPS25730SRSMR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS25730SRSMR — Power Management & Signal Chain | Superb Automation

TPS25730SRSMR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS25730SRSMR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS25730SRSMR USB Type-C and USB PD sink controller with a gate driver for an external power path

The TPS25730S is the member of the TPS25730 family that drives external FETs instead of integrating the switch. The port negotiation, the configuration channel handling and the protection comparators are the same as on the integrated member, but the current path runs through FETs that sit outside the controller, so a port that has to carry more current than a single package can hold, or that has to use a FET already on the approved list, can still be built around this controller.

Two gates are provided, one for the VBUS side FET and one for the system side FET. The controller turns them on with a controlled slew, turns them off in normal shutdown, and turns them off in a few microseconds when the reverse comparator or the overvoltage comparator crosses. That arrangement gives the port a defined behaviour on a hot unplug without any firmware in the product.

Key parameters taken from the TPS25730SRSMR document

Supply3.0 V to 3.6 V on the 3.3 V rail
VBUS range4 V to 22 V on VBUS, with the system side allowed over the same range
Power pathExternal FETs driven from GATE_VBUS and GATE_VSYS, so the current rating is set by the FETs on the board
Gate driveTwo separate gate outputs, one per side of the path
Soft start2.8 V per millisecond minimum, 3.3 typical and 3.8 maximum, with the gate capacitor between 500 pF and 16 nF for the specified slope
Overvoltage responseThe external FET is disabled within 3 to 5 microseconds of the comparator crossing, including the comparator delay
Reverse responseThe FET is disabled within 1 to 2 microseconds when the reverse comparison threshold is crossed
Normal shutdown450 to 4000 microseconds to disable the external FET, which is the interval where the gate is discharged through the internal path
Reverse comparison2 mV minimum, 6 mV typical and 10 mV maximum threshold
ESD1000 V human body model and 500 V charged device model
LDO outputs1 mA from the 3.3 V LDO and 5 mA from the VBUS LDO
ConfigurationResistor straps, no firmware in the host
InterfacesI2C, GPIOs and ADC inputs
PackageWQFN of 38 pins, the same body as the integrated member
Carrier3000 pieces on a large reel
MoistureLevel 2 at 260 degrees with a one year floor life
Part marking25730S
TemperatureMinus 40 to plus 125 degrees on the controller

Every row above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for a first article.

Where the numbers matter in a real build

The choice between the integrated and the gate drive member is a thermal and sourcing decision, not a functional one. The integrated member carries the current through a 16 milliohm path inside the package and is rated at 7 A. A port that needs 5 A continuously at a high ambient, or that has to use a FET with a lower resistance than the integrated path, is better served by the gate drive member, because the heat is then spread over a FET that was chosen for the board and can be cooled.

The gate capacitor is the element that sets the slew, and the document specifies the slope only for a gate capacitance between 500 pF and 16 nF. Below that range the turn on is faster than the specified window, which increases the inrush into the load capacitance; above it the port takes longer to reach the negotiated voltage and a device may time out before the rail is up. The resistor and capacitor pair on the gate is therefore a calculated value, not a copied one.

The reverse path response of 1 to 2 microseconds is what protects the port on a hot unplug. When the cable is removed the source collapses and the load capacitance would otherwise discharge back through the FET body diode into the connector. The controller sees the inversion at 6 mV typical, turns the FET off in about a microsecond, and the discharge path is broken before the connector pins arc.

The normal shutdown interval is much slower than the fault path, at 450 to 4000 microseconds, because it discharges the gate through an internal resistance instead of a hard pull. That difference is intentional: a commanded shutdown should not create a voltage step on the system rail, while a fault should. A product that needs the fast path for a commanded shutdown is using the wrong pin.

Because the current does not pass through the package, the controller temperature is set by its own quiescent current and by the gate charge it delivers, not by the load current. That is the advantage of this member on a port that runs at high current: the controller can sit at a comfortable temperature while the FET carries the heat, and the FET can be selected for its thermal path rather than for its package size.

  • The FET pair, because the current rating and the on resistance of the port are decided by those parts and not by the controller.
  • The gate capacitor, since the slew is specified only between 500 pF and 16 nF.
  • The reverse comparator path, because a hot unplug event is where a port without it fails.
  • The 3.3 V rail sequencing against VBUS, because the controller has to be alive before it can protect the path.
  • The strap resistors, which fix the port behaviour in hardware.
  • The gate drive strength against the gate charge of the chosen FET, since a large FET with a slow gate lengthens every timing in the document.

Which projects this part fits

This part fits docking stations, monitors that supply power to a notebook, multi port adapters and any product where the power path is built from discrete FETs already qualified on the platform. It also fits boards where the current is above what an integrated switch can carry, or where the thermal budget rules out a switch inside a controller package.

Questions that come up before a purchase order is released

Why choose this member over the integrated one?

Because the current path runs through external FETs. That allows a higher current, a lower resistance or a FET that is already qualified on the platform, at the cost of two extra parts and a gate network.

What sets the soft start time?

The gate capacitor, in the 500 pF to 16 nF window the document specifies, together with the internal current that charges it. Outside that window the slope is not covered by the printed limits.

How fast does the port turn off on a fault?

The reverse comparator disables the FET in 1 to 2 microseconds, and the overvoltage comparator in 3 to 5 microseconds, both including the comparator delay.

Can the two gates be used separately?

They are separate outputs, one for the VBUS side and one for the system side, and the document gives a timing row for each. The sequencing between them is what decides which side is protected first.

Does the port need firmware?

No. The port behaviour is set by resistor straps. The I2C interface is for monitoring and configuration readback.

Is the package the same as the integrated member?

It is the same 38 pin WQFN body, but the pin functions differ between the two members, so one board footprint does not accept both.

How SUPERB handles this line

Controllers that drive external FETs are usually chosen late in a programme, when the thermal budget or the approved parts list forces the switch out of the controller package. Our power management cross reference lists the devices this part is cross referenced against, our supplier quality audit covers the supplier checks we run on controllers of this class, and our pin to pin cross reference is the cross reference route when a board has to move from one member of the family to the other.