TPS2556DRBR
Product Specifications
TPS2556DRBR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS2556DRBR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS2556DRBR precision adjustable current limited power distribution switch, 500 mA to 5 A
The TPS2556 is a power distribution switch with a programmable current limit between 500 mA and 5 A, set by one resistor. It is the part that sits between a 5 V rail and a USB connector, or between a rail and any load that must not be allowed to pull the supply down, and it does that with a 22 milliohm FET and a constant current loop rather than a fuse.
The family covers two members, the TPS2556 and the TPS2557, and the document prints the same electrical table for both. The differences are in the limit range and the accuracy at the top of it, so the orderable number has to be read against the table rather than assumed from the family name. The switch also carries a fault flag with a deglitch window, built in soft start, and thermal shutdown that acts at a lower threshold while the part is in current limit.
Key parameters taken from the TPS2556DRBR document
| Operating range | 2.5 V to 6.5 V on the input |
| Adjustable limit | 500 mA to 5 A typical, set by a resistor on ILIM |
| Limit accuracy | 6.5 per cent at 4.5 A, which is the tightest row printed for the family |
| Overcurrent response | 3.5 microsecond typical response into a short |
| High side switch | 22 milliohm typical at 25 degrees and 25 milliohm maximum at the same temperature, with 40 milliohm typical over the full range |
| Standby supply current | 2 microamp maximum when the switch is off |
| Soft start | Built in, which holds the inrush into a capacitive load inside the current limit instead of letting it trip |
| Resistor range | 20 k to 187 k recommended on ILIM |
| Worked limit points | About 4.1 A to 4.7 A at 24.9 k, about 1.6 A to 2.0 A at 61.9 k and about 1.1 A to 1.3 A at 100 k |
| Fault flag | Open drain output, 180 mV low level at 1 mA, with a 6 to 13 millisecond deglitch before it asserts or releases |
| Thermal shutdown | 155 degrees normally and 135 degrees while the part is in current limit, with 20 degrees of hysteresis |
| Undervoltage lockout | 2.35 V rise point with 2.45 V of hysteresis on the input pin |
| Supply current | 35 microamp typical and 120 microamp maximum enabled at 6.5 V with no load |
| System ESD | 15 kV air and 8 kV contact at system level |
| Approvals | UL listed under file E169910 and CB certified to IEC 60950-1 amendment 2 edition 2.0 |
| Package | VSON of 3.00 mm by 3.00 mm, eight pins |
| Carrier | 3000 pieces on a large reel |
| Moisture | Level 2 at 260 degrees with a one year floor life |
Every row above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for a first article.
Where the numbers matter in a real build
The limit resistor is the whole calibration of the part. The document prints three worked points and the equation that connects them, and a board that copies a resistor value from another board without checking the equation can end up with a limit 30 per cent off. The 20 k to 187 k window is the range where the internal loop is specified, so a value outside it is not covered by the table even if the switch still works.
The deglitch window is the difference between a switch that survives a plug in event and one that flags a fault every time a device with a large input capacitor is connected. The fault flag is delayed by 6 to 13 milliseconds, and the current limit loop acts in 3.5 microseconds, so the loop controls the current while the flag waits to see whether the event is real. A system that polls the flag faster than the deglitch window will read the pin before it can possibly have moved.
The two thermal shutdown thresholds are a deliberate arrangement. While the part is in current limit the die is dissipating and the limit is 135 degrees, which acts early; when the part is not in current limit the limit is 155 degrees, which avoids a nuisance shutdown on a warm board. Both carry 20 degrees of hysteresis so the part does not oscillate around the threshold.
The 22 milliohm FET gives 0.2 W at 3 A and 0.55 W at 5 A. In a 3 mm by 3 mm VSON the pad has to be soldered to copper, and the current rating the customer cares about is the one that keeps the junction under the limit in their enclosure. A 5 A load at 40 degrees ambient on a four layer board is a different case from the same load on a two layer board with no copper pour.
The ESD and certification rows are worth reading before a product goes to a safety house. The switch carries UL listing under the file number printed in the document and a CB certificate to IEC 60950-1 amendment 2 edition 2.0, and the system level ESD figures are 15 kV air and 8 kV contact. Those are the numbers a test house will ask for, and they apply to the part, not to the finished product.
- The resistor value against the required limit, computed from the vendor equation and not copied from another board.
- The load capacitance, because the soft start and the current limit together decide how long the rail takes to come up.
- The fault flag timing against the firmware that polls it, since the flag has a 6 to 13 millisecond delay.
- The thermal path, because 5 A through 22 milliohm is over half a watt in a 3 mm body.
- The undervoltage lockout, which releases the switch below about 2.35 V and takes the load down with it.
- The reel and the moisture level, because level 2 parts need a bake decision after the floor life expires.
Which projects this part fits
This part fits USB ports and hubs, digital televisions, set top boxes, voice over IP phones, and any board that has to limit a 5 V branch without a fuse that needs replacing. It also fits equipment with a hot pluggable module where the inrush of a large capacitor would otherwise trip the upstream supply.
Questions that come up before a purchase order is released
Is the current limit a fuse replacement?
It behaves like a resettable fuse for overloads, because the part goes into constant current and recovers when the load comes back. It is not a substitute for a fuse on a safety critical rail, since a failed FET can still short the input to the output.
What does the 6.5 per cent accuracy mean in practice?
At a 4.5 A setting the limit sits within about 300 mA of the nominal value. A load that draws just under the limit on a cold board can cross it on a warm one, so the margin has to be taken from the window and not from the typical value.
Why are there two thermal thresholds?
The lower one, 135 degrees, applies while the part is in current limit and dissipating. The higher one, 155 degrees, applies in normal operation to avoid a shutdown on a board that is simply warm.
Does the part need an external capacitor on the output?
The document calls for 0.1 microfarad or more on the input. The output capacitance is a system decision, and the soft start is what keeps the inrush into it inside the current limit.
What is the difference between the TPS2556 and the TPS2557?
The two members differ in the limit range and in the accuracy printed at the top of it. The document prints the table for the family, so the exact row has to be read for the member on the order.
Can the part be used above 5 A?
No. The printed range stops at 5 A typical, and the 22 milliohm FET in this body would not carry more without exceeding the thermal limits.
How SUPERB handles this line
Power switches are bought on two numbers, the limit window and the thermal path, and both are printed in the vendor document rather than in a distributor line. Our power management cross reference lists the devices this part is cross referenced against, our pin to pin cross reference explains how we check a drop in replacement before it goes on a board, and our kitting service covers the kitting side when the switch, the connector and the resistor have to arrive together.