Contact Us

TPS2552DRVR

Brand: Texas Instruments
Texas Instruments TPS2552DRVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS2552DRVR — Power Management & Signal Chain | Superb Automation

TPS2552DRVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS2552DRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS2552DRVR: an adjustable current limited power switch that sets its limit with one resistor

TPS2552DRVR is a power distribution switch whose current limit is programmed by a single resistor from 75 mA to 1.7 A in a WSON (DRV) body of 6 pins. It works from 2.5 V to 6.5 V, carries up to 1.5 A of continuous load current, and sets its current limit with a resistor between 15 k and 232 k on the limit pin. Accuracy at the top of the range is plus or minus 6 per cent, the overcurrent response is 2 microseconds, and the high side switch is 85 milliohms in the SOT-23 body. The enable pin is active low on this member, the fault output is open drain and deglitched, and reverse input to output voltage protection keeps the switch alive when the output is held above the input.

Order code and package

TPS2552DRVRthe constant current member with an active low enable in the 6 pin WSON body, which is the version a system that enables on a low signal orders
TPS2553the same switch with an active high enable, so the two are separated by the polarity of one pin and nothing else
TPS2552-1 and TPS2553-1the latch off versions, which stay off after an overcurrent event until the enable is cycled, where the plain members retry into the fault
Limit resistor75 mA to 1.7 A from 232 k down to 15 k, with the resistor tolerance directly in the current limit accuracy
Fault outputopen drain and deglitched, so a short transient does not assert a fault to the controller
Bodiesthe 6 pin WSON used here and a 6 pin SOT-23 of 2.9 mm by 1.6 mm, with 85 milliohms of high side resistance quoted for the SOT-23

Electrical parameters that decide the application

Input voltage2.5 V to 6.5 V, which covers a 3.3 V and a 5 V rail with tolerance
Load currentup to 1.5 A continuous, with the current limit set below that figure for most loads
Current limit range75 mA to 1.7 A typical, programmed by a resistor between 15 k and 232 k
Limit accuracyplus or minus 6 per cent at the 1.7 A setting, widening at the low end where the offset of the sense circuit dominates
Response time2 microseconds typical from an overcurrent event to the switch entering current limit, which is what protects a connector and a trace
On resistance85 milliohms high side in the SOT-23 body, which at 1 A is 85 mV of drop and 85 mW of dissipation
Enableactive low on this member, with the switch on when the pin is pulled low
Fault outputopen drain, asserted on current limit and on overtemperature, deglitched so a transient does not reach the controller
Reverse voltage protectionthe switch blocks current from output to input when the output is held above the input, which protects a rail that is back driven
Soft startcontrolled rise time on the switch, which limits the inrush into a capacitive load
Thermal shutdownjunction overtemperature turns the switch off, and the fault output reports it
Operating rangeminus 40 C to 105 C junction on the limit specification, which is the window the accuracy figures are quoted over

Enable polarity, latch behaviour and the resistor table

TPS2552DRVRthis order code, the constant current member with an active low enable in the 6 pin WSON body
TPS2553the same switch with an active high enable, separated by the polarity of one pin
TPS2552-1 and TPS2553-1the latch off versions, which stay off after a fault until the enable is cycled
Limit resistor15 k to 232 k sets 1.7 A down to 75 mA, and the resistor tolerance enters the limit accuracy directly
Bodiesthe 6 pin WSON used here and a 6 pin SOT-23 of 2.9 mm by 1.6 mm, where the 85 milliohm figure is quoted
Fault outputopen drain and deglitched, so a short transient does not reach the controller
Reverse behaviourthe switch blocks output to input current, which is not the same as surviving a reversed supply

Points to check before this part goes on a BOM

The limit resistor sets the protection, and its tolerance is part of the answer. A 1 per cent resistor gives the limit accuracy printed in the table; a 5 per cent resistor adds its own error on top. On a USB port where the host has to supply 500 mA and the connector is rated at 1 A, the limit has to sit between those figures with both tolerances included, and that is a calculation rather than a resistor picked from a graph.

Constant current is not latch off. This member holds the output at the limit while the fault lasts, so a shorted load draws the limit current and the switch gets hot. The -1 versions latch off instead, which protects the switch but leaves the load unpowered until the enable is cycled. The choice depends on whether the system can tolerate a retry or needs a hard stop.

2 microseconds is fast enough to protect a trace and not fast enough to protect a die. The switch reacts inside 2 microseconds, which is well inside the thermal time constant of a PCB trace. A dead short still puts the full limit current through the switch until the thermal shutdown acts, so the switch has to be able to carry the limit current continuously.

Latch off versions need a recovery path. A product that latches off on a transient short and has no way to cycle the enable is a product that comes back from the field. The recovery has to be in the firmware, and it has to be tested, or the plain retry version is the safer choice.

Reverse voltage protection is not reverse polarity. It stops the switch from conducting backwards when the output is above the input. A reversed supply at the input still destroys the part, and a board that can see a reversed connector needs a protection device in front.

The WSON body has a thermal pad, and it is the ground. The pad is the return path and the heat path at the same time. A pad with voids under it raises the junction temperature and lowers the current the switch can carry before thermal shutdown, which shows up as a limit that trips below the resistor setting.

Where a resistor programmed limit beats a fixed one

A USB port has a fixed requirement, and a fixed limit switch is the right part. A board with several downstream loads on one rail, a hot swap slot, or a peripheral connector with its own current budget needs the limit matched to the load, and that is what the resistor does. It also lets the same part number serve several products, which reduces the number of lines on the bill of materials.

The resistor is also a tuning point. A product that trips on inrush can raise the limit or slow the rise time without a board change, and a product that has to protect a smaller connector can lower it. That flexibility is worth something on a board that is already in production.

Reading the limit table correctly

The current limit is quoted as a window, not a point, and the window widens as the setting falls because the offset of the sense amplifier becomes a larger share of the total. A board that needs 500 mA of limit has to place the whole window below the connector rating, which usually means setting the nominal figure below the target rather than at it.

Where this order code fits

a downstream load on a shared 5 V rail, a hot swap slot, or a peripheral connector where the current limit has to match the load rather than a standard Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

How is the current limit set? By a resistor between 15 k and 232 k on the limit pin, which programs a limit from 1.7 A down to 75 mA. The resistor tolerance is part of the limit accuracy.

What happens during a short? The switch enters constant current mode and holds the limit until the fault clears or thermal shutdown acts. The -1 versions latch off instead and need the enable cycled.

Is the enable active high or low? Active low on the TPS2552 and active high on the TPS2553, which are otherwise the same switch.

How fast does it react? 2 microseconds typical from an overcurrent event, which protects the trace and the connector rather than the switch die.

Can the output be held above the input? Yes, the switch blocks reverse current in that condition. That is not the same as reverse polarity protection at the input.

How does SUPERB supply this part? With the exact ordering string, the body, the date code and the packing on the offer, and the enable polarity stated, because one pin separates this part from the member most often substituted for it.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.