Contact Us

TPS2552DBVR

Brand: Texas Instruments
Texas Instruments TPS2552DBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS2552DBVR — Power Management & Signal Chain | Superb Automation

TPS2552DBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS2552DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS2552DBVR: 2.5 V to 6.5 V, 1.5 A adjustable current-limited power switch

TPS2552DBVR is a power-distribution switch with a programmable current limit and reverse-voltage protection in a SOT-23 body of 6 pins. It passes up to 1.5 A from a 2.5 V to 6.5 V rail through an 85 milliohm high-side FET, sets its current limit anywhere from 75 mA to 1.7 A with one external resistor, and holds the output in constant-current mode instead of shutting down when the load exceeds that limit.

Order code and package

Ordering stringTPS2552DBVR, DBV package, SOT-23, tape and reel
Family membersTPS2552 and TPS2553 (constant current), TPS2552-1 and TPS2553-1 (latch off)
Package6-pin SOT-23, 2.90 mm by 1.60 mm, with a power pad
Ambient range-40 C to 85 C
Pin count checkIN, OUT, EN, FAULT, ILIM and GND, all six used in a normal circuit
ApprovalsUL listed under file E169910 and NEMKO IEC60950-1-am1 ed2.0

Electrical parameters that decide the application

Input range2.5 V to 6.5 V, so a 5 V USB rail is inside with room for tolerance
Load currentUp to 1.5 A continuous
Switch resistance85 milliohm typical in the DBV package
Current limit75 mA to 1.7 A set by RILIM, accuracy plus or minus 6 percent at 1.7 A
Resistor range15 kohm to 232 kohm across the limit window
Overcurrent response2 microseconds typical into a hard short
Supply current120 microamp on, 0.1 microamp off
Undervoltage lockout2.35 V rising, with hysteresis
ESD15 kV per IEC 61000-4-2, and only with the external capacitance fitted

Points to check before this part goes on a BOM

At the top of the current range the package, not the silicon, sets the limit. 1.5 A through 85 milliohm is 0.19 W, and the SOT-23 body in this data sheet is listed at 182.6 C/W, which is a 35 C rise: at an 85 C ambient the junction is already near 120 C before any copper is counted. The same part in the 2 mm by 2 mm WSON is listed at 72 C/W, so the package choice, not the current rating, decides whether 1.5 A is available continuously.

The limit resistor runs the opposite way to intuition: 15 kohm is the top of the window at 1.7 A and 232 kohm is the bottom at 75 mA, because the limit current falls as the resistor rises. An earlier revision of this document started the range at 19.1 kohm and the current revision starts at 15 kohm, so a board built to the older note cannot reach the top of the window.

A 1.5 A switch on a 500 mA USB port is three times the port specification and will not protect the upstream supply. The resistor has to be picked from the port budget, not from the switch rating, and the 20 kohm value in the typical application is the one that puts a standard port limit inside the window rather than at the device maximum.

The 15 kV ESD figure is quoted with external capacitance on the port. Without that capacitor the protection falls back to the device level rating in the ESD table, which is a fraction of 15 kV, so a board that omits the 0.1 microfarad input and 120 microfarad output parts loses the headline number as well as the inrush control.

The two operating states are not symmetrical in a battery product: 120 microamp on is 1.05 Ah over a year and 0.1 microamp off is 0.9 mAh, a difference of three orders of magnitude. A host that leaves the switch enabled while the product sleeps spends more energy in the switch than in most of the loads it feeds, and the EN pin has to be driven rather than left floating.

The constant-current version and the latch version behave differently in the same socket. TPS2552 holds the output at the limit for as long as the fault lasts and recovers on its own, while TPS2552-1 opens the switch and stays open until the enable pin is cycled. A board that expects a self-resetting port will appear dead with the -1 part fitted, and the two share the same pinout and the same resistor value.

Where this order code fits

The usual fit is a USB port, a hub, a docking connector or a 5 V accessory rail where the source has to survive a shorted cable and the load needs a defined inrush rather than a hard step. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can this replace a TPS2550 or TPS2551 directly? The data sheet states backwards compatibility with those two parts, so the pinout and the enable sense match. The limit resistor still has to be recalculated, because the older 19.1 kohm floor no longer describes the current window.

What happens if the output is pulled above the input? An internal comparator turns the switch off and FAULT goes low, which protects the parts on the input side. This is the case a diode would normally cover, and it is the reason the part is used on a connector that a user can back-feed.

Is 6.5 V enough for a 5 V rail with transients? The absolute maximum is above that, but the recommended operating range stops at 6.5 V, so a 5 V rail with a 30 percent transient sits exactly on the limit. The clamp has to come from the upstream converter or a TVS, not from this part.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.