Contact Us

TPS2511DGNR

Brand: Texas Instruments
Texas Instruments TPS2511DGNR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS2511DGNR — Power Management & Signal Chain | Superb Automation

TPS2511DGNR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS2511DGNR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS2511DGNR: USB dedicated charging port controller and current limited switch for vehicle and wall chargers

TPS2511DGNR is a USB dedicated charging port controller with an integrated current limiting power switch in a HVSSOP body of 8 pins. It presents the three charging signatures a phone or tablet looks for on the data lines, shorted D+ to D-, the 2 V and 2.7 V divider in either order, and 1.2 V on both lines, and it switches between them by itself once a device is attached. The current limit is set by one resistor on ILIM_SET, so the same body covers a 1 A accessory port and a 2.3 A fast charge port.

Order code and package

TPS2511DGN8-pin HVSSOP (DGN), 80-piece tube, marking 2511
TPS2511DGNR8-pin HVSSOP (DGN), 2500-piece large reel, marking 2511
TPS2511DGNR.Asame body and reel, alternate assembly row, NIPDAUAG finish
Temperature range, all rows-40 C to 125 C
Moisture sensitivity, all rowsLevel-2-260C-1 YEAR

Electrical parameters that decide the application

Input voltage on IN4.5 V to 5.5 V
High side switch on resistance70 mOhm typical, 105 mOhm maximum at 2 A, 25 C
OUT short circuit current limit, RILIM 44.2 kOhm1060 mA minimum, 1160 mA typical, 1270 mA maximum
OUT voltage that starts hiccup, RILIM 210 kOhm3.6 V minimum, 3.8 V typical, 4.1 V maximum
UVLO on IN, rising3.9 V minimum, 4.1 V typical, 4.3 V maximum
Supply current with EN low0.1 uA typical, 2 uA maximum at 5.5 V
Thermal shutdown155 C
Load detect current threshold, RILIM 22.1 kOhm1060 mA
ILIM_SET resistor window16.9 kOhm to 750 kOhm, 210 kOhm recommended ceiling

Charging signatures the part presents

BC1.2 dedicated charging portD+ shorted to D-, the signature an Android handset expects
Divider mode2.7 V on D+ and 2.0 V on D-, the divider signature Apple devices look for
Divider mode, reversed2.0 V on D+ and 2.7 V on D-, used where the cable is not straight through
1.2 V on both linesthe third scheme, for accessories that do not follow BC1.2
Automatic selectionthe part reconnects the data lines itself once a device is attached
Disabled stateboth data pins go high impedance, so an unpowered port does not load the bus

Points to check before this part goes on a BOM

The current limit is a resistor value, not a fixed rating. With 22.1 kOhm on ILIM_SET the vendor quotes a plus or minus 10 per cent limit at 2.3 A typical, while the 44.2 kOhm row lands at 1.16 A typical, so a port stamped 2 A needs the resistor chosen against the port rating and then measured on the bench rather than copied from a reference circuit.

Hiccup starts when OUT falls below 3.8 V typical, and that threshold is deliberately close to a loaded 5 V rail. A long or thin cable that drops 1.2 V under 2 A will trip the protection before the phone reaches full current, which is why the CS pin exists: it feeds the cable drop back into the regulation loop so the port keeps charging at the far end of the cable.

The undervoltage lockout on IN sits at 4.1 V typical, rising. A vehicle port that sags to 4.0 V during crank or during a cold start will drop out and renegotiate the charge, and the phone restarts its charging handshake each time. If the rail is known to sag, the port needs bulk capacitance ahead of the part rather than a different order code.

The high side switch is 70 mOhm typical but 105 mOhm maximum at 2 A and 25 C, so the conduction loss at 2 A is 0.42 W in the worst case. The DGN body is a PowerPAD part and the exposed pad has to be soldered to copper, otherwise the junction climbs into the 155 C thermal shutdown before the port reaches its rated current.

Leakage with EN low is 0.1 uA typical but 2 uA maximum at 5.5 V. On a vehicle module that sleeps for weeks this is not the number that drains the battery, but a board with several ports multiplies it, and the enable line has to be driven from the module controller rather than tied to the rail.

The ILIM_SET pin has a stated window of 16.9 kOhm to 750 kOhm for loop stability, and the vendor recommends staying at or below 210 kOhm. A value above that window is sometimes used to reach very low limits, and the result is a port that oscillates around the threshold instead of limiting cleanly.

The data line pins are rated to 5.5 V and go high impedance while the part is disabled. That matters on a hub where several ports share the same upstream controller: a disabled port must not hold D+ or D- low, or the host sees a permanent attach event.

The OUT short circuit current limit is a current, not a foldback, so a dead short holds the port at roughly 1.16 A with 44.2 kOhm until hiccup takes over. Cable and connector ratings should be checked against that number, not against the nominal port current, because a shorted cable passes the limit current through the connector shell.

Both the tube and the reel rows carry the same marking, 2511, and the same moisture level, Level-2-260C-1 YEAR. A production line that receives a partial reel and a tube in the same week cannot tell them apart by marking, so the floor life clock has to come from the pack label rather than the device.

The part is a charging controller, not a data switch with high speed lanes. It passes the D+ and D- signatures and the CS feedback, and a product that also needs USB 2.0 data through the same connector needs a separate data switch rated for the signal rate, with the two parts sharing the connector but not the same pins.

A vehicle port also has to survive the accessory that is plugged in the wrong way and the charger that is unplugged under load. The part blocks current from OUT back to IN while it is disabled, which protects the source, but the connector pins are still exposed to an ESD event, so the suppressor belongs on the connector side of the part, with a clamp voltage that stays under the 5.5 V pin rating at the peak current the standard specifies. That clamp is what stands between a customer and a dead port.

Where this order code fits

It sits on the outside of a vehicle charger, a wall adapter or a multi port hub, between the 5 V rail and the USB connector, where a cable fault, a cheap cable or a device that asks for more than the port can give has to be contained without dropping the rail that feeds the rest of the product. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

Will this charge an Apple device at full current? The divider signature at 2.7 V on D+ and 2.0 V on D- is the one Apple hardware looks for, and the part generates it automatically. The 1.2 V signature and the shorted line signature cover the BC1.2 and the Chinese standard schemes, so one part covers the three families that appear in the field.

What decides the port current? The resistor on ILIM_SET. 22.1 kOhm gives the 2.3 A typical limit quoted in the feature list and 44.2 kOhm gives 1.16 A typical, both with the tolerance stated in the electrical table. The port connector and the cable then decide what the phone actually draws.

Can two ports share one device? No. Every port needs its own controller and its own switch, because the current limit and the hiccup state belong to a single output. Two ports on one device would share one limit and one fault state, and a short on one port would take the other down.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.