TPS2412PWR
Product Specifications
TPS2412PWR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS2412PWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS2412PWR N+1 and ORing power rail controller for redundant supplies
The TPS2412 is an ORing controller that drives an external N channel MOSFET so that it behaves like a diode with a very low forward drop. It sits between a source and a common rail and holds the MOSFET on while the source is the higher of the two, then turns it off when the source falls below the rail. The part is the reduced feature member of the TPS2410 and TPS2411 pair, and it is aimed at servers and telecom equipment where two or more supplies feed one rail.
The forward drop is regulated to about 10 mV instead of the 400 mV a Schottky diode would take, which on a 20 A rail is the difference between 200 mW and 8 W of loss. A resistor from the RSET pin programs the turn off threshold, and leaving the pin open gives a slightly positive threshold, which is the setting that lets the part share current between two sources rather than letting one carry everything.
Key parameters taken from the TPS2412PWR document
| Function | ORing and N+1 controller with an external N channel MOSFET as the pass device |
| Input range | 3 V to 16.5 V on VDD, with the source and rail pins operating from 0.8 V to 16.5 V |
| Forward regulation | 10 mV typical with a 7 to 13 mV window between the source and the rail |
| Turn off threshold | Programmed by a resistor on RSET, with the open pin giving a slightly positive threshold |
| Turn off time | 70 ns in the electrical table with a 3.24 k resistor on RSET |
| Gate drive | 7 V typical above the source with a 6 to 8 V window at a 3 V supply |
| Soft turn off sink | 10.2 mA typical with a 9 to 12.5 mA window, which is the controlled turn off rather than the fast one |
| Supply current | The controller draws from the rail it is protecting, with the bias stored on a capacitor from BYP to the source pin |
| BYP capacitor | Required, and the document gives the range rather than a single value |
| Package | TSSOP PW, 8 pins, 2000 pieces on a large reel, and SOIC D, 8 pins, 2500 pieces on a large reel |
| Moisture | Level 1 at 260 C with unlimited floor life on the PW rows |
| Temperature | Minus 40 to 85 C on the addendum rows and in the electrical tables |
| Addendum status | TPS2412PWR, TPS2412PWR.B and TPS2412PWRG4 are Active and in Production, marking 2412 |
| Orderable note | The SOIC rows TPS2412D and TPS2412DR are also Active, at 75 pieces in a tube and 2500 pieces on a large reel |
Every row above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for a first article.
Where the numbers matter in a real build
The RSET resistor is the difference between a part that shares current and a part that does not. With the pin open the turn off threshold is slightly positive, which means the MOSFET is turned off as soon as the source falls below the rail by a small margin, and the two sources then share the load in proportion to their regulation. With a resistor fitted the threshold moves, and the part turns off at a defined negative margin, which is what a product wants when one supply should carry the whole load and the second should only take over on a failure.
The 10 mV forward regulation is a loop, not a switch. The controller modulates the gate to hold the drop at the set point, so the MOSFET runs in its linear region and dissipates the product of the drop and the current. At 20 A that is 200 mW, which a single MOSFET in a power package handles easily. It also means the gate is not a clean logic level, and a probe on the gate shows a slow loop response rather than a square wave.
The 70 ns turn off time is what makes the part usable on a redundant bus. When a supply fails, the rail has to be held up by the other source before the failing one drags it down, and the controller has to get out of the way faster than the bulk capacitance on the failed source can discharge. The fast path turns the gate off hard, then the soft turn off path with its 10.2 mA sink takes over for the slower part of the transition, which is how the part avoids a negative spike on the rail.
The bias arrangement is a frequent source of trouble on a first article. The controller is powered from the rail it protects, and the charge pump that drives the gate stores its energy on the capacitor from BYP to the source pin. That capacitor has to be close to the pins and has to be sized inside the range the document gives, because a capacitor that is too small droops when the gate is driven and a capacitor that is too large slows the start up of the bias.
The two package options are not interchangeable in thermal terms. The TSSOP body at 2000 pieces on a reel is the usual choice for a server board, and the SOIC body at 2500 pieces on a reel is the choice where the board has room and the pin pitch matters for rework. Both are Active in the current addendum, so a product that has one in its bill of materials does not need to change it.
- RSET resistor value against the load sharing the product needs, since the open pin and a fitted resistor give different behaviour.
- Forward drop at the actual load current, because the loop holds the drop but the MOSFET has to be able to carry the current in its linear region.
- Turn off time against the bulk capacitance on the source that fails, since the rail has to be held by the other source.
- BYP capacitor value inside the range in the document, placed at the pins.
- Gate voltage against the gate rating of the chosen MOSFET, since the drive is 7 V above the source.
- Package choice against the thermal path available on the board, since the controller dissipates from its own bias.
Which projects this part fits
This part fits server and telecom boards with N+1 redundant supplies, dual feed line cards, storage shelves with two power inlets, and any product that has to OR two batteries or two adapters onto one rail. It also fits products that currently use a Schottky ORing diode and need the loss back, because the forward drop falls from hundreds of millivolts to about 10 mV at the same current.
Questions that come up before a purchase order is released
What is the difference from the TPS2410 and TPS2411?
Those are the fuller feature members with linear gate control, voltage monitoring and a status pin. The TPS2412 and TPS2413 are the reduced pin count versions, with on and off gate control and an adjustable turn off threshold. The comparison table in the document lists which feature belongs to which part.
Why is the forward drop regulated rather than switched?
Because a switched MOSFET would let the rail sag to the drop of its body diode during the handover. Holding the drop at about 10 mV keeps the rail steady and makes the two sources share in a predictable way.
Can two of these share current?
Yes, with the RSET pin open, which gives a slightly positive turn off threshold. Two controllers on two sources will then both stay on while their sources are close, and the sharing follows the regulation of the sources.
What MOSFET should be used?
An N channel device with a gate rating above the drive voltage and an on resistance chosen so that the linear region dissipation is inside the package. The document's application diagram shows the source and rail connections.
Does the part need a separate supply?
No, it takes its bias from the rail it protects and stores the gate drive energy on a capacitor from BYP to the source. That capacitor is the part that has to be placed carefully.
What happens during a hot plug?
The controller turns the MOSFET on into the load capacitance and the loop limits the inrush by holding the forward drop. A product with a very large load capacitance should check the start up against the SOA of the chosen MOSFET.
How SUPERB handles this line
We supply the TPS2412PWR on original 2000 piece reels, and we can quote the SOIC rows on 2500 piece reels from the same addendum. The power management cross reference page lists the ORing and hot swap controllers we carry by voltage and current, pin to pin cross reference covers the pass devices that sit next to them, and safety stock planning is how we hold cover on the controllers that go into a long life telecom build.