Contact Us

TPS2400DBVR

Brand: Texas Instruments
Texas Instruments TPS2400DBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS2400DBVR — Power Management & Signal Chain | Superb Automation

TPS2400DBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS2400DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS2400DBVR overvoltage protection controller that drives an external N channel MOSFET

The TPS2400 is a small controller that protects a load from an overvoltage event by switching a series N channel MOSFET off. It contains a trimmed reference, an oscillator, a charge pump, a comparator and the logic that drives the gate, and it leaves the pass device to the board, which is how a product chooses the current rating and the on resistance it needs. The input pins are rated to 110 V absolute maximum, so the part survives the transient levels that appear on an automotive or industrial rail.

The comparator window is set by an external divider from the rail. The gate is driven by a charge pump that lifts the gate above the source, so an N channel MOSFET in the high side position can be used without a second supply, and a shut off MOSFET inside the part pulls the gate down when the window is exceeded. The document describes the purpose as surviving extended overvoltage events, which is the load dump case in a vehicle and the inductive kick case on a long industrial cable.

Key parameters taken from the TPS2400DBVR document

FunctionOvervoltage protection controller with an external N channel MOSFET as the pass device
Input rating110 V absolute maximum on VIN, minus 0.3 V on the low side
Gate rating22 V continuous on the gate output, which is the limit the charge pump works inside
Internal reference1.15 V, used by the overvoltage comparator against the external divider
Overvoltage hysteresis150 mV typical with a 135 to 165 mV window, measured with a 10 nF load on the gate
Undervoltage lockout3.0 V typical on the input, 2.9 to 3.1 V window, which keeps the gate off until the internal rail is valid
Gate drive19 V typical above the source, 20 V maximum, from the internal charge pump
Gate sink current485 mA typical with a 350 to 600 mA window, which is what discharges the gate on a fault
Turn off propagation0.1 to 0.6 microsecond, which is the delay from the comparator crossing to the gate moving
Input supply currentIn the tens of microamp range at low input and rising with the rail, which is what the charge pump costs
PackageSOT-23 DBV, 5 pins, 3000 pieces on a large reel and 250 pieces on a small reel
MoistureLevel 2 at 260 C with a one year floor life
TemperatureMinus 40 to 85 C ambient, with the junction allowed to 125 C
Addendum statusTPS2400DBVR, its .A row, TPS2400DBVRG4 and the 250 piece small reel row are all Active and in Production, marking BIJ

Every row above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for a first article.

Where the numbers matter in a real build

The value of this part is in the speed of the turn off, not in the threshold accuracy. The comparator crosses and the gate is pulled down in a fraction of a microsecond, and the gate sink current of 485 mA is what makes that possible with a real MOSFET gate. A product that puts a 100 nF gate capacitor on the device to slow the turn on will also slow the turn off, so the gate resistor and the gate capacitor belong in the same decision as the threshold divider.

The 110 V absolute maximum is the number to check against the transient the product will actually see. An automotive load dump can reach far above that, and the part is intended to work behind a TVS that clamps the event below the rating. The document shows a TVS in its application diagram for exactly this reason, and a board that leaves the TVS out is relying on the controller to survive something it was not rated for.

The charge pump is the reason the part can drive an N channel device in the high side. It lifts the gate about 19 V above the source, so a logic level MOSFET with a 10 V gate rating needs a clamp or a different device, and a standard 20 V gate part is the right match. The document limits the gate output to 20 V maximum, and a MOSFET with a lower gate rating than that has to be protected by the choice of device, not by a resistor.

Hysteresis of 150 mV sounds small against a 12 V rail until the divider is considered. The divider scales the rail down to 1.15 V, so 150 mV of hysteresis at the comparator pin is 150 mV times the divider ratio at the rail. With a divider that maps 20 V to 1.15 V the ratio is about 17, which makes the effective hysteresis about 2.6 V at the rail. That is the number that decides whether the load chatters when a transient sits right at the threshold.

The five pin body has no thermal pad, so the dissipation budget for the controller is small and the pass device carries the loss. That is why the external MOSFET matters: the controller heats by the gate charge it delivers at each switching event and by the charge pump current, not by the load current, so a 5 A load and a 0.5 A load heat the controller the same.

  • MOSFET gate rating against the 20 V maximum the charge pump can deliver.
  • Divider ratio and the resulting hysteresis at the rail, not at the comparator pin.
  • TVS clamp voltage against the 110 V absolute maximum, with the pulse shape the standard actually uses.
  • Turn off time from the gate capacitance and the 485 mA sink current, since a large gate capacitor slows the protection.
  • Undervoltage lockout behaviour at 3 V, because the gate is undefined below it.
  • Input supply current budget, since the charge pump draws from the same rail it is protecting.

Which projects this part fits

This part fits automotive and industrial products that have to survive a load dump or a long cable transient: dashboard accessories, telematics units, DC-DC converters fed from a vehicle harness, industrial sensors on a 24 V bus, and telecom line cards with a hot pluggable feed. It also fits products that need a protected output but cannot justify a dedicated protection IC with an integrated FET, because the external device can be sized for the current and the on resistance the product needs.

Questions that come up before a purchase order is released

Can the part be used as an undervoltage lockout?

The comparator window is set by the divider, so a product can set the lower edge as well as the upper edge. The internal undervoltage lockout at 3 V is separate and keeps the gate off until the part's own rail is valid.

What MOSFET suits this controller?

An N channel device with a gate rating above 20 V, a threshold low enough to turn on at the charge pump voltage, and an on resistance chosen for the load current. The document's application diagram uses a logic level device with a TVS on the input.

How fast does it turn off?

The propagation delay is 0.1 to 0.6 microsecond and the gate sink current is 485 mA typical, so the gate discharges quickly for a normal gate capacitance. The turn off time then depends on the gate charge of the chosen MOSFET.

Does it protect against reverse polarity?

Not by itself. The body diode of the N channel MOSFET conducts in the reverse direction, so a product that needs reverse protection needs a different topology or an additional device.

What sets the overvoltage point?

The divider from the rail to the comparator input against the internal 1.15 V reference. The hysteresis is 150 mV at the pin, which becomes larger at the rail by the divider ratio.

Is the part automotive qualified?

The addendum rows for this body do not carry a Q1 suffix, so the automotive reading of the catalogue string is not confirmed by the document. A product that needs AEC-Q100 should confirm the orderable string before releasing a purchase order.

How SUPERB handles this line

We supply the TPS2400DBVR on original 3000 piece reels and as 250 piece small reels, with the date code and marking recorded. The power management cross reference page lists the protection controllers we carry by voltage class, incoming inspection plan covers the checks we run on reels that go into automotive builds, and supplier quality audit describes how we trace the lot behind a shipment when a customer needs the chain documented.