Contact Us

TPS23731RMTR

Brand: Texas Instruments
Texas Instruments TPS23731RMTR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS23731RMTR — Power Management & Signal Chain | Superb Automation

TPS23731RMTR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS23731RMTR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS23731RMTR IEEE 802.3bt Type 3 powered device interface with a no-opto flyback controller in one package

The TPS23731 puts a Power over Ethernet powered device interface and a current mode flyback controller into one 45 pin VQFN. It covers the 802.3bt Type 3 range for Class 1 to Class 4 and also the older 802.3at, and it supports operation up to 30 W at the powered device input. The hotswap MOSFET inside the part is a 100 V device with 0.3 ohm typical on resistance, so a 25.5 W load at 48 V does not need an external pass FET.

The controller behind the interface is built for flyback topology with primary side regulation. It takes feedback from an auxiliary winding instead of an optocoupler and a shunt regulator, which removes two parts from the isolated side and removes the tolerance stack that comes with them. It also carries a soft start with advanced startup, hiccup mode overload protection, soft stop, adjustable frequency with synchronisation, programmable dithering, automatic maintain power signature and an adapter priority input.

Key parameters taken from the TPS23731RMTR document

PoE standardIEEE 802.3bt Type 3 Class 1 to 4 and IEEE 802.3at, up to 25.5 W at the PD input with 30 W operation supported
Hotswap MOSFET100 V rated, 0.3 ohm typical on resistance, integrated into the interface
Input operating rangeVDD, RTN, GND and AGND 0 to 60 V, measured against VSS
Hotswap current limit0.925 A typical with a 0.75 to 1.1 A window, read with the return pin pulsed at 1.5 V
Inrush termination90 percent of the inrush current typical, with an 80 to 99 percent window and an 84 ms inrush delay
UVLO37.6 V rising with a 35.8 to 39.5 V window, 32 V falling, 6 V hysteresis
Detection current398 microamp typical at the mark state, 391 to 406.2 microamp window
Classification current18.6 mA typical with a 69.8 ohm resistor on CLS, 17.6 to 19.4 mA window
Maintain power signature12.5 mA typical in the low state and 19 mA typical in the pulsed high state, with EMPS open
Switching frequency248 kHz typical with a 60.4 k resistor on FRS, 223 to 273 kHz window, dithering set on DTHR
Maximum duty cycle78.5 percent typical with a 24.9 k resistor on DTHR
Controller supplyVCC undervoltage lockout 8.25 V rising and 6.1 V falling with 2.15 V hysteresis
Adapter priorityAPD input threshold 1.5 V rising, which hands the rail to a local adapter and disables the hotswap
Load regulationPlus or minus 1.5 percent typical at 5 V with a synchronous rectifier over 0 to 100 percent load, plus or minus 3 percent at 12 V with a diode rectifier over 5 to 100 percent
Thermal38.5 degrees per watt junction to ambient in the RMT body, with separate case paths of 3.9 and 9.1 degrees per watt for the two thermal pads
PackageVQFN RMT, 45 pins, 3000 pieces on a large reel, NIPDAU finish, moisture level 3 at 260 C with a 168 hour floor life
TemperatureMinus 40 to 125 C junction, as printed in both the electrical tables and the addendum
Addendum statusTPS23731RMTR and TPS23731RMTR.A both Active and in Production, 3000 pieces on a large reel, marking DB0 WA1

Every row above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for a first article.

Where the numbers matter in a real build

Primary side regulation is the reason to choose this part and also the reason a first article has to be measured rather than assumed. The feedback winding has to track the output winding, which means the two windings sit on the same limb with the same number of turns per volt and short leakage paths. When that holds, the document claims plus or minus 1.5 percent load regulation at 5 V with a synchronous rectifier across the whole load range. The 12 V diode rectified case is quoted as plus or minus 3 percent over 5 to 100 percent of load, and the difference between those two rows is the honest headline: a transformer that is not tightly coupled will sit outside both.

The current limit is a single number with a wide window, 0.925 A typical and 0.75 to 1.1 A over the part. A 25.5 W load at a 37 V worst case rail draws 0.69 A, so the bottom of the window still covers the load with margin, but a product that runs at 30 W from a 44 V rail draws 0.68 A and has almost nothing left. That is the case where the inrush and the steady state have to be checked on the bench with the actual transformer and the actual bulk capacitor, because the part cannot tell the two apart on a first pulse.

The maintain power signature behaviour is what keeps a PSE from dropping a product that goes to sleep. With the EMPS pin open the part draws 12.5 mA typical in the low state and 19 mA typical in the pulsed state, and the automatic mode stretches both the amplitude and the duration of the pulse when the load current falls. A battery powered camera that shuts its radio down at night still has to hold the signature, and the automatic behaviour means that requirement does not have to be met by a resistor that burns power all the time.

Adapter priority is a small feature with a large effect on field behaviour. When the APD pin rises above 1.5 V the interface turns the hotswap off and lets the local adapter feed the product, which keeps a PoE switch port from carrying the load of a product that also has a barrel jack plugged in. The pin needs a divider from the adapter rail, and the divider has to be set so that the pin stays below the threshold while the adapter is unplugged and its output capacitor is still charged.

The two thermal pads are separate on purpose. The interface side and the controller side each have their own path to the board, 3.9 and 9.1 degrees per watt junction to case, against 38.5 degrees per watt junction to ambient on the evaluation board. A four layer board with a solid ground plane under both pads is what the number assumes, and a two layer board with a hatched plane will run hotter than the table suggests at the same copper area.

  • Class resistor and detection resistor values against the class the PSE is expected to assign, checked with a 1 percent resistor.
  • Inrush into the bulk capacitor with the actual capacitance and the actual ESR, not with the value on the released bill of materials.
  • Auxiliary winding coupling and the number of turns per volt, which decide whether the regulation rows apply at all.
  • Maintain power signature at the lowest load the product reaches in its sleep state.
  • Adapter priority divider behaviour while the adapter is unplugged and its output capacitor still holds charge.
  • Junction temperature of both thermal pads at full load in the enclosure, since the ambient figure assumes an evaluation board.

Which projects this part fits

This part fits the class of product that has to carry a full 25.5 W over the Ethernet cable and still want a small isolated supply: pan tilt zoom cameras with heaters, outdoor access points with a second radio, video phones, and industrial gateways with a redundant power feed. It also fits products that are fed from either PoE or a local adapter, because the adapter priority input handles that handover without an extra comparator. Where the load is under 13 W the smaller member of the same family is cheaper and easier to route, and where the product needs a secondary side regulated output with tight cross regulation the controller also supports that mode.

Questions that come up before a purchase order is released

Does the part need an optocoupler?

No. The controller regulates from an auxiliary winding, which is why the isolated side has no shunt regulator and no optocoupler. The document also states that secondary side regulation is supported, so a product that needs a very tight output can still use feedback from the secondary.

How accurate is the output without an optocoupler?

The document quotes plus or minus 1.5 percent typical at 5 V with a synchronous rectifier across 0 to 100 percent load and plus or minus 3 percent at 12 V with a diode rectifier over 5 to 100 percent. Both rows assume the auxiliary winding tracks the output winding, so the transformer is part of the accuracy budget.

What sets the switching frequency?

A resistor from FRS to the return rail. With 60.4 k the part runs 248 kHz typical with a 223 to 273 kHz window. Dithering is set separately by a capacitor and a resistor on the DTHR pin, and with DTHR shorted to the bias rail the dithering is off.

Can the part run from an adapter and PoE at the same time?

Yes, and the APD pin decides which source wins. When the pin exceeds 1.5 V the hotswap is disabled and the adapter feeds the load. The pin has to be driven by a divider that stays under the threshold when the adapter is removed.

What happens on an output overload?

The controller enters hiccup mode, which restarts the converter after a delay instead of holding the fault. The current limit turn off delay is 60 ns typical, and the hotswap current limit sits at 0.925 A typical, so a short on the isolated side is limited by the hotswap and not by the transformer.

Is the package a standard land pattern?

It is a 45 pin VQFN with two separate thermal pads. The footprint has 45 pads plus the two exposed areas, and the solder paste example in the document uses a 0.125 mm stencil with 76 and 78 percent pad coverage on the two exposed areas.

How SUPERB handles this line

We supply the TPS23731RMTR on original 3000 piece reels with the date code and the marking recorded on the packing list. The power management cross reference page lists the PoE interface and hot swap parts we carry by voltage and current class, pin to pin cross reference covers the case where a second source has to sit on the same land pattern, and kitting service is how we deliver the interface, the transformer and the surrounding passives against one build.