TPS2331ID
Product Specifications
TPS2331ID
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS2331ID from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS2331ID active high hot swap controller in the fourteen pin SOIC, single channel with circuit breaker
The TPS2331 is the active high member of the same hot swap controller family as the TPS2330: one N channel MOSFET on a 3 V to 13 V rail, a circuit breaker set by two resistors, a transient timer set by a capacitor, and power good plus fault reporting. This order code is the fourteen pin SOIC in a 50 piece tube, which is the package a prototype or a low volume build uses.
The silicon is identical to the TSSOP member and the only functional difference is the enable polarity, which matters when a board carries both parts across revisions. The rest of the behaviour is the same: the gate ramps at a rate set by the gate capacitor, the sense voltage is compared against a threshold set by the ISET resistor, and a fault that outlasts the timer pulls the gate down and latches the fault output until the enable is cycled.
Key parameters taken from the TPS2331ID document
| Input range | 3 V to 13 V on the main input, with the internal regulator supply at 3 V to 5.5 V |
| Circuit breaker threshold | 19 mV typical at a 400 Ohm ISET resistor, 50 mV at 1 kOhm and 73 mV at 1.5 kOhm, with the current equal to that voltage over the sense resistor |
| Timer | 50 microamp typical charge current into a 0.5 V threshold, so roughly 10 milliseconds per microfarad of timer capacitor |
| Timer window | 0.4 V to 0.6 V on the threshold, which is a 20 per cent spread on the fault time |
| Enable | Active high on this member, with an internal pull up of 100 to 300 kOhm, a 2 V maximum high threshold and a 0.8 V minimum low threshold |
| Supply current | 1 mA maximum operating and 5 microamp maximum standby |
| Gate clamp | Integrated clamp on the gate to discharge path, which protects the external FET |
| Reporting | Power good with a filter, and a fault output that latches until the enable is cycled |
| Protection | Circuit breaker with a transient timer, so a short current excursion does not trip the rail |
| Package | SOIC D fourteen pins |
| Packing | 50 pieces in a tube as this order code, while the R suffix on the same code is 2500 pieces on a large reel |
| Marking | TPS2331I on the body |
| Temperature | Minus 40 to 85 C |
Every row above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for a first article.
Where the numbers matter in a real build
The tube packing is the detail that decides whether this order code suits a build. Fifty pieces in a tube is a prototyping quantity: it does not go through a pick and place machine without a tube feeder, and a production line that runs reels will stop. The reel row is the same die with an R before the package letter, 2500 pieces on a large reel, and the two are electrically identical. A customer who sends this exact string for a production order usually means the reel, and the purchase order should say so before the line is set up.
The active high enable changes the failure mode of the surrounding circuit. With an internal pull up of 100 to 300 kOhm, an unconnected enable pin reads as a high and the controller comes up enabled. On a board where the enable comes from a processor that is held in reset, the pin is high impedance and the rail turns on before the firmware is ready. That is sometimes what the product wants, because the card has to power its own supervisor, and sometimes it is exactly wrong. The pull up value is wide, so the external resistor that sets the default has to be much lower than 100 kOhm to be deterministic.
The sense resistor and the ISET resistor have to be read as a pair. The document gives three ISET points and the threshold scales with the resistor, so a 1 kOhm ISET with a 5 mOhm sense gives a 10 A trip point and the same ISET with a 2 mOhm sense gives 25 A. A board that changes the FET to a larger one and reduces the sense resistor to cut the drop has to reduce the ISET resistor as well, or the protection moves out of reach. The offset of the sense amplifier, printed as 5 microamp maximum of input bias current, is the floor on how small the sense resistor can be before the trip point becomes uncertain.
The 5 microamp standby current is a maximum over temperature, not a typical, and it is the number to use on a battery rail. The operating current of 1 mA is also a maximum and includes the gate supply, which is generated internally and runs continuously while the controller is enabled. On a 12 V rail that supply is a small fraction of the load, and on a 3.3 V rail the same controller is a larger share, which is why the document prints the current as a single figure with the input range noted in the conditions.
- Tube against reel packing, because this order code is fifty pieces in a tube and production needs the R suffix.
- Enable polarity and the default state of the pin when the driver is high impedance.
- The ISET and sense resistors as a pair, since the trip current is their ratio.
- Timer capacitor against the load step the rail actually sees.
- Gate capacitor and FET gate charge, because the ramp time depends on both.
- Standby current of the whole input path, including any external divider on the enable.
Which projects this part fits
This part fits prototype and low volume builds of plug in cards, backplane modules, fan trays and instruments that need a latched overcurrent trip on a 12 V or 3.3 V rail. It also fits any product where the enable comes from a supervisor that drives the pin actively in both states, because the active high polarity then matches the logic and no inverter is needed.
Questions that come up before a purchase order is released
Why is this part in a tube?
Because the order code without the reel suffix is the tube row, 50 pieces. The same die is available as TPS2331IDR on a 2500 piece reel. A production order should use the R suffix, and a prototype can use the tube.
Does the enable need an external resistor?
The pin has an internal pull up of 100 to 300 kOhm, which is too wide to define a default level. An external resistor of 10 kOhm or less to the rail or to ground sets the state while the driver is high impedance.
What is the fault behaviour?
The gate is pulled down and the fault output latches. The controller does not retry until the enable is cycled, which is why the part is used where a permanent short must not produce repeated inrush events.
How accurate is the trip point?
It depends on the ISET threshold window, the sense resistor tolerance and the amplifier offset. The document prints the threshold at three ISET values and the bias current as 5 microamp maximum, and a production test should measure the trip point on the first article rather than calculate it.
Can it be used on a 5 V rail?
Yes. The input range starts at 3 V, and the internal regulator needs 3 V to 5.5 V on its own pin. A 5 V rail is inside the range, and the gate drive is then generated from the regulator rather than from the rail.
How SUPERB handles this line
We supply the TPS2331ID in the 50 piece tube for prototypes and the TPS2331IDR on 2500 piece reels for production, and we record the marking TPS2331I at goods in so the polarity can be confirmed against the bill of materials. The power management cross reference page lists the hot swap controllers by polarity and package, kitting service covers the case where a build needs both the tube and the reel of the same die, and obsolete part cross reference hub is where we record the substitutes when a body goes end of life.