TPS22966DPUR
Product Specifications
TPS22966DPUR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS22966DPUR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS22966DPUR: a dual 6 A load switch with 16 mOhm on resistance per channel, a separate bias rail and a slew rate set by a capacitor on each channel
TPS22966DPUR is two independent P channel switches in one 3 mm by 2 mm body, each gated by its own enable pin, each with its own ramp capacitor, so two subsystems can be powered up in a chosen order from one rail in a WSON body of 14 pins. The DPU body is fourteen pins on 3.00 mm by 2.00 mm with a thermal pad, and the part needs a bias supply between 2.5 V and 5.5 V on top of the rail it switches, which is the detail that decides whether it fits a board.
Order code and package
| Catalogue string | TPS22966DPUR, the R letter being the 3000 piece large reel row |
| Body | WSON, DPU, fourteen pins, 3.00 mm by 2.00 mm, thermal pad on the underside |
| Reel | 3000 pieces on a large tape and reel for the R row, 250 pieces on a small reel for the T row, and the addendum prints A and B revision rows at both quantities |
| Finish and moisture | NIPDAU plating, moisture level 2, 260 C, one year floor life |
| Temperature | minus 40 to 105 C free air, which is a package rating and not a junction figure |
| Marking | RB966 |
| Document | SLVSBH4F, June 2012, revised July 2016 |
| Bias requirement | VBIAS is a separate supply between 2.5 V and 5.5 V that powers the gate drive, and the switched rail VIN can sit anywhere from 0.8 V up to that bias level |
Electrical parameters that decide the application
| Input range | VIN 0.8 V to 5.5 V per channel, with the recommended operating window for best resistance being 0.8 V up to VBIAS |
| Bias range | VBIAS 2.5 V to 5.5 V, and the bias current is what the quiescent figures describe |
| On resistance | 16 mOhm typical and 19 mOhm maximum at 25 C with a 5 V bias, unchanged from 5 V input down to 0.8 V input, and 21 mOhm maximum over minus 40 to 85 C and 23 mOhm over the full range |
| Continuous current | 6 A per channel maximum, with two channels in one package so the pair carries 12 A in total |
| Quiescent current | 80 uA typical with both channels on and 60 uA with one, 120 uA maximum over temperature, and 2 uA typical in shutdown |
| Off state current | 0.07 uA per channel at 3.3 V and 0.5 uA maximum at 5 V, which is what the rail sees while the switch is open |
| Ramp control | a capacitor on each CT pin sets the slew rate, and the capacitor has to be rated for 25 V or more for the published timing |
| Rise time | 1720 us at 5 V in with a 1000 pF capacitor, 2275 us at 2.5 V in with a 5 V bias, 325 us at 0.8 V in with a 5 V bias, and 875 us at 0.8 V in with a 2.5 V bias |
| Turn on delay | 460 us at 5 V in and 990 us at 2.5 V in with a 1000 pF capacitor, so the timing budget has to include the delay and the ramp |
| Discharge | a 220 Ohm on chip resistor from output to ground when the switch is off, 300 Ohm maximum |
| Enable levels | the ON pins interface directly with 1.2 V, 1.8 V, 2.5 V and 3.3 V logic, and the pins must not be left floating |
| Protection | no current limit appears in the specification, so a load that can short needs protection outside the switch |
Reel rows, revision rows and the single channel neighbours
| TPS22966DPUR | the 3000 piece large reel row used on this page, marking RB966 |
| TPS22966DPUT | the same device on 250 pieces small reel |
| TPS22966DPUR.A and .B | two revision rows printed at the same quantity in the same body, which only the reel label separates |
| TPS22966DPUTG4 | the green material row on the small reel |
| Neighbouring single channel parts | the TPS22910A and TPS22965 cover one channel each where two are not needed, and the TPS22925 covers 3 A in a wafer scale body |
Points to check before this part goes on a BOM
The bias rail is the first thing to check on a board. This is not a switch that runs from the rail it passes. VBIAS has to be between 2.5 V and 5.5 V, and the gate drive comes from it, so the resistance figures are quoted against a 5 V bias and the ramp times change when the bias drops to 2.5 V. A board that wants to switch a 1.2 V rail from a battery has to have a 3.3 V or 5 V housekeeping rail available and alive before the switch is enabled, which is a sequencing constraint rather than a wiring detail.
The resistance is remarkably flat across the input range, which is the point of the dual channel part. 16 mOhm at 5 V and 16 mOhm at 0.8 V means a 1.2 V rail at 6 A drops only 96 mV and dissipates 576 mW, and a 0.9 V rail at 6 A dissipates the same 576 mW in a body that is 3 mm by 2 mm with a thermal pad. That is a real heat source next to whatever it feeds, and the thermal pad has to be soldered to a copper area rather than left as a mechanical feature.
The ramp capacitors are per channel and that is what makes the part useful for sequencing. A 1000 pF capacitor gives 1720 us at 5 V in, and a larger capacitor stretches it further, so a channel feeding a 100 uF load can be given a slow ramp while the other channel comes up quickly. The capacitors have to be rated for 25 V, which is a strange requirement for a 5.5 V rail until the ramp is seen from the CT pin's side of the circuit: the pin sees the full swing of the gate drive and a low voltage capacitor will lose capacitance and change the timing.
There is no current limit and no thermal shutdown listed. The specification covers resistance, quiescent current, ramp and discharge, and nothing else. A short on one channel therefore produces whatever current the source can deliver until something else gives way, and that something is usually a trace or a connector. Where a load can short, the protection has to come from a fuse, a current limited source or a hot swap controller ahead of the switch, and the switch is then a sequencing element rather than a protective one.
The discharge resistor is 220 Ohm and it is always present on this part. Two supplies feeding one node through two of these switches is a common arrangement, and the disabled channel puts 220 Ohm from the node to ground, which at 3.3 V is 15 mA of load on the other supply. That current does not appear on any drawing unless the resistor is drawn, and on a battery rail it is the difference between a month of standby and a week. The single channel family has members without the resistor where that matters.
The addendum prints A and B revision rows at the same quantity and the same body. Nothing in the part number tells a buyer which silicon is inside, and the electrical tables in this revision apply to all of them. For a production order that is usually harmless, but a line that has qualified one revision and is buying on a price break should ask which revision is on the reel, because a change of silicon is exactly the kind of event that moves a resistance figure by a milliohm and a ramp time by a few per cent.
Sequencing two rails from one source
Two channels in one package are usually used for a core rail and an input output rail on the same processor, and the order matters. The core rail comes up first in most families, then the input output rail, and the gap between them is set by the ON pins rather than by the ramp capacitors. The ramp capacitor sets how fast a rail arrives once its pin is asserted, and the delay of 460 us at 5 V in is the time before the ramp starts. A controller that asserts both pins at once still gets a staggered ramp because the two capacitors differ, but the reliable way to sequence is to drive the second ON pin from the power good of the first rail's regulator.
The inrush calculation is the other half of the same decision. A 100 uF load ramped over 1720 us at 5 V draws an average of about 290 mA, and a load ramped over 325 us draws 1.5 A. Both are inside the 6 A rating, and the second one is enough to droop a source with a high output impedance, which is what a boost converter or a long cable looks like. Slower is not always better either: a long ramp keeps the FET in its linear region for longer and raises the dissipation, which is why the vendor publishes the timing rather than a single recommended capacitor.
What the 6 A rating really covers
The rating is a maximum continuous switch current, and the switch is a pair of FETs with a thermal pad. At 6 A and 16 mOhm the conduction loss is 576 mW per channel, and 1.15 W for the pair, in a 3 mm by 2 mm body. The thermal resistance is not printed in this revision for the DPU body, so the rise has to be measured or taken from the board's own thermal model. A pair running at 6 A each on a four layer board with a solid ground plane is a different proposition from a pair running on a two layer board with a narrow pour.
The current is also shared across fourteen pins, and the input pins are doubled on the package for that reason. A board that feeds the two input pins through a single thin trace undoes the point of the package, and the resistance from the pin to the copper becomes part of the drop. The 16 mOhm figure is a die and package figure, and the board adds to it. On a 0.9 V rail at 6 A, 10 mOhm of board resistance is another 60 mV of drop, which is more than the switch itself contributes.
Where this order code fits
This is the pair of switches between a system rail and two subsystems on a notebook, a tablet, a set top box or a residential gateway, where the two loads need separate enables and separate ramp times Teams comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and teams replacing a part that has gone end of life start from the Power Management Cross Reference page.
Questions buyers ask
Can it switch a rail without a bias supply? No. VBIAS has to be between 2.5 V and 5.5 V and it powers the gate drive. The switched rail can be as low as 0.8 V, and the resistance figures are quoted against a 5 V bias.
Is 6 A per channel a continuous rating? It is the maximum continuous switch current. At 6 A the channel dissipates 576 mW, so the answer on a given board depends on the copper under the thermal pad and on the ambient.
How is the ramp set? A capacitor on the CT pin for each channel, rated for 25 V or more. 1000 pF gives 1720 us at 5 V in, and a larger capacitor stretches the ramp.
Is there any protection inside? No current limit and no thermal shutdown are specified. A load that can short needs a fuse, a current limited source or a hot swap controller ahead of the switch.
What happens to the output when the switch is off? A 220 Ohm on chip resistor discharges it, and while the switch is open the channel draws 0.07 uA from the rail at 3.3 V.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.