TPS22965TDSGRQ1
Product Specifications
TPS22965TDSGRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS22965TDSGRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS22965TDSGRQ1: 5.7 V, 6 A load switch with 16 milliohm on resistance and a configurable rise time
TPS22965TDSGRQ1 is a single channel load switch that puts a 6 A rail on and off without the inrush spike that a plain FET and a capacitor produce in a WSON (DSG) body of 8 pins. It passes 6 A from 0.8 V to 5.7 V with 16 milliohm of on resistance, holds that resistance flat down to 1.2 V because the gate drive runs from a separate bias pin, and sets its output ramp with one capacitor, so the inrush into a large load capacitor is a calculated figure rather than a surprise.
Order code and package
| Ordering string | TPS22965TDSGRQ1, the DSG body with the quick output discharge and the automotive suffix |
| Body | 8 pin WSON, 2.00 mm by 2.00 mm, with an exposed thermal pad on the underside |
| Device in this document | TPS22965 and TPS22965N. The T version carries the on chip quick output discharge; the N version does not |
| Automotive version | Documented as a separate device, TPS22965-Q1, in the vendor's automotive portfolio. The Q1 qualification does not come from this document |
| Input range | 0.8 V to 5.7 V on VIN, with a separate VBIAS pin that runs the internal gate drive |
| Current rating | 6 A continuous, limited by the package and the board rather than by the die |
| Control | A single ON pin with a 1.2 V logic threshold, so 1.2 V, 1.8 V, 2.5 V and 3.3 V logic all drive it directly |
Electrical parameters that decide the application
| On resistance | 16 milliohm typical and 21 milliohm maximum at 25 degrees with a 5 V bias, rising to 23 milliohm at 85 degrees and 25 milliohm at 105 degrees |
| On resistance across VIN | The same 16 milliohm typical at 3.6 V, 3.3 V, 1.8 V, 1.5 V and 1.2 V in, which is unusual: most switches give up resistance as the input falls |
| Quiescent current | 50 uA typical and 75 uA maximum on VBIAS with the switch on and no load |
| Shutdown current | 5 nA typical and 2 uA maximum on VBIAS, 2 nA typical on VIN at 5 V with the switch off |
| Quick output discharge | 225 ohm typical, 300 ohm maximum, on the T version only, which pulls the output down when the switch opens |
| Rise time | Set by a capacitor on CT. With 1000 pF the data sheet tables give output rise times from about 380 us to 2.5 ms depending on VBIAS and VIN, and turn on times from 730 us to 2.4 ms |
| Turn off time | 9 us to 100 us in the same tables, so the switch opens far faster than it closes |
| Bias supply | VBIAS runs the gate drive and is quoted at 2.5 V and 5 V in separate tables. The resistance figures and the timing both change with it |
| Thermal | The 8 pin WSON with its pad is the only heat path. At 6 A and 16 milliohm the part dissipates 0.58 W, which the pad has to carry into the board |
| Logic threshold | 1.2 V typical, compatible with low voltage GPIO without a level shifter |
| Temperature range | minus 40 to 105 degrees ambient in the published rows |
Family variants and how they differ
| TPS22965 against TPS22965N | The T version has the 225 ohm output discharge, the N version does not. A rail that must fall quickly when switched off takes the T; a rail that must float takes the N |
| TPS22965 against the -Q1 | The automotive part is a separate document with its own qualification and its own orderable rows. This page describes the industrial silicon, and the catalogue string carries the automotive suffix |
| Bias from the load rail | Where VIN is 1.2 V or 1.8 V, VBIAS has to come from a higher rail such as 3.3 V or 5 V. Tying VBIAS to VIN works only when VIN is above about 2.5 V |
| Rise time choice | A larger CT slows the ramp and lowers the inrush into a big output capacitor. The trade is a longer window in which the switch is in its linear region and dissipating |
| No current limit | The part has no current limit and no over temperature protection of its own. A short on the output is cleared by the upstream supply, not by the switch |
| Alternatives in the same family | The vendor's load switch range covers 2 A, 3 A and 6 A members with and without discharge. The 6 A member on this page is the one for a rail that feeds a drive or a bank of capacitors |
Points to check before this part goes on a BOM
There is no current limit and no thermal shutdown inside this part. A load switch without current limit relies on the upstream converter, so a shorted output has to be handled by the supply or by a fuse.
The catalogue string carries the automotive Q1 suffix, but the vendor documents the Q1 device separately. A purchase order should name the exact orderable row and the qualification document should be confirmed before the part goes on a production BOM.
The rise time tables are quoted at 1000 pF on CT and at specific VBIAS and VIN points. Rise time scales with CT, so a 10 nF capacitor stretches the ramp by roughly an order of magnitude and cuts the inrush by the same factor.
On resistance is flat across VIN from 5.7 V down to 1.2 V, which is the reason to use a biased switch rather than a plain P-channel FET on a low voltage rail. The 16 milliohm at 1.2 V is the figure that decides whether a 6 A rail can pass through a 2 mm package.
The 6 A rating is a package and board rating. At 6 A the part dissipates 0.58 W, and a 2 mm square body with a poor pad reaches 105 degrees quickly. A four layer board with vias under the pad is the normal arrangement.
The discharge resistor is 225 ohm typical. On a 100 uF output capacitor that is a 22 ms discharge to 37 per cent, which is fast enough for a power cycle but not a short circuit.
What a load switch buys over a discrete FET
A P-channel FET and a gate resistor will switch a rail, but the ramp depends on the gate capacitance, the resistor and the temperature, and the inrush into the load capacitor is whatever the FET happens to pass. A load switch sets the ramp with an external capacitor and holds it across temperature, which is what a hot pluggable module or a drive needs.
The second gain is the bias supply. Running the gate drive from a separate rail lets the switch pass a 1.2 V rail with 16 milliohm of resistance, which no plain P-channel FET achieves at that gate voltage. The price is one more supply pin on the package.
Where this order code fits
Solid state drives, notebooks, docking stations and consumer equipment that switch a 3.3 V or 5 V rail to a subsystem and need the rail to come up in a controlled ramp. The part also suits a 1.8 V or 1.2 V rail where the switch has to work from a bias supply and still pass several amps with millivolts of drop. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.
Questions buyers ask
Does this part limit inrush current? It limits the rate of rise, not the current. A slower ramp reduces the peak charging current into the output capacitor, but a shorted output still draws whatever the upstream supply can deliver.
Can VBIAS be tied to VIN? Only when VIN is above roughly 2.5 V. Below that the gate drive has no headroom and the vendor's tables specify VBIAS separately from VIN.
What is the difference between the T and the N order codes? The T version has an on chip 225 ohm resistor that discharges the output when the switch opens. The N version leaves the output floating.
Is the Q1 suffix in the ordering string the automotive part? The vendor documents the automotive device as TPS22965-Q1 in a separate data sheet. This document covers the industrial silicon, so the automotive qualification should be confirmed against that document and the exact addendum row before ordering.
What happens at 6 A in a 2 mm package? The part dissipates about 0.58 W. With a four layer board and a proper via field under the pad the junction stays inside the 105 degree ambient rating; with two layers and a small pad it does not.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Date Code Management page sets out the checks that keep a substitute from failing on the bench.