Contact Us

TPS22963CYZPR

Brand: Texas Instruments
Texas Instruments TPS22963CYZPR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS22963CYZPR — Power Management & Signal Chain | Superb Automation

TPS22963CYZPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS22963CYZPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS22963CYZPR: 5.5 V, 3 A load switch, 13 milliohm, reverse current protection, WCSP-6

TPS22963CYZPR is an N channel load switch with 13 milliohm on resistance, a controlled turn on and reverse current protection while it is disabled in a DSBGA body of 6 pins. The switch is built into a 1.4 mm by 0.9 mm wafer level body, which is small enough to sit next to the connector it protects. The reverse current protection is the reason it appears on battery rails: when the switch is off, current cannot flow from the load back into the cell.

Order code and package

TPS22963CYZPRActive, DSBGA-6, 3000 pieces on a large reel, SNAGCU finish, MSL-1-260C unlimited floor life, marking BD
TPS22963CYZPTActive, 250 pieces on a small reel, the same body
TPS22964Cthe sibling with quick output discharge, which this string does not have
Body size1.4 mm by 0.9 mm, 0.5 mm pitch, 0.5 mm height
Temperature rangeminus 40 to 85 degrees, which is narrower than the leaded alternatives

Electrical parameters that decide the application

Input voltage1 V to 5.5 V
Continuous current3 A maximum
On resistance13 milliohm typical at 5 V, 14 milliohm at 3.3 V, 18 milliohm at 1.8 V
Shutdown current760 nanoamp typical
Control threshold1.3 V, so a low voltage GPIO can drive it directly
Turn oninternal slew rate control, so the inrush is limited without an external capacitor
Reverse currentblocked while the switch is disabled
ESD2 kV human body model, 500 V charged device model

Family variants and how they differ

TPS22963Ccontrolled turn on, no output discharge, the string on this page
TPS22964Cthe same switch with quick output discharge, for rails that must fall quickly
Bodysix terminal wafer level package, no leads and no visible solder joint
ON pin1.3 V threshold, works from a 1.8 V GPIO
Familyhigher current members of the same family sit in larger bodies

Points to check before this part goes on a BOM

The FET is 8 milliohm and the switch is 13 milliohm. The difference is the package and the internal connection. The number to use for dissipation is 13 milliohm, because that is what the part presents at the pins. At 3 A that is 0.12 W, which in a 1.4 mm by 0.9 mm body is a real temperature rise and the reason the ambient rating stops at 85 degrees.

Reverse current protection only works while the switch is disabled. That is deliberate: the part allows intentional reverse current when it is on, which is useful in a system where a rail can be driven from two sources. The protection is for the off state, where a charged load would otherwise push current back into a discharged cell.

There is no quick output discharge on this string. The sibling TPS22964C has it. A board that needs the rail to fall quickly when the switch opens has to use the other part or add a resistor and a FET, because this one leaves the output floating and the load capacitance discharges through whatever the load draws.

The turn on is internally controlled. There is no capacitor to set the rise time, unlike the leaded switches in the same class. The slew rate is fixed, which makes the part easy to use and removes the ability to tune the inrush for a very large load capacitance. If the inrush is too high for the source, the answer is an inductor in series or a switch with a configurable ramp.

Seven hundred and sixty nanoamp in shutdown is the sleep budget. For a battery product that switches a subsystem off between uses, that is the current the subsystem still costs. It is low enough for a monthly duty cycle and high enough that a product which switches the rail off and expects zero is measuring something else as well.

Wafer level packages cannot be inspected. There are no leads and no fillet, so a joint that did not form is not visible. That is a process control issue rather than a part issue, and it is why boards in this class are usually built with an x ray or a daisy chain test coupon. The 0.5 mm pitch also rules out hand rework for most repair shops.

Eighty five degrees is a limit worth reading twice. The leaded switches in the same class reach 105 degrees. A board inside a sealed enclosure near a power stage can exceed 85 degrees ambient, and this part will not be the one to survive it. The smaller body is a space decision that costs thermal margin.

The 3 A rating needs a real copper connection. Two terminals carry the current and they are 0.5 mm apart. The trace into and out of the part has to be wide enough for 3 A, and the vias to the plane have to be counted rather than assumed. Most failures of a switch this size are the board, not the silicon.

The A suffix on the addendum is a material revision. The same ordering string is listed twice with different plating and MSL data. A customer with a material declaration on file needs the row identified on the offer, because the part is functionally identical and the paperwork is not.

What to confirm before this part goes on a purchase order

Confirm whether the board needs the output discharge. This string does not have it, the TPS22964C does, and the two look identical on a reel apart from the ordering string.

Ask for the date code and the reel label, and confirm the assembly house can place a wafer level part at 0.5 mm pitch. A part that arrives for a repair bench with no rework capability is a part that cannot be used.

For a battery rail, state the shutdown current and the reverse blocking requirement together. A part that blocks reverse current only when disabled is the right answer for a rail that is either on or off, and the wrong answer for a rail that is back fed while it is on, which is a common arrangement in a system with two supplies, which is where a rail can be driven from the port side while the battery is still connected. State which case applies before the offer is written, and before the reel is reserved, because the two answer the same question.

Where this order code fits

It switches a 3 A branch of a battery rail in a tablet or an SSD, and blocks the reverse current that would otherwise flow back into a discharged cell. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

Does it block reverse current when it is on? No. Reverse current is blocked only while the switch is disabled. When it is on the channel conducts in both directions, which allows intentional back feeding but not protection.

Is there a current limit? No. The part is a switch with a controlled turn on and no current limit. A short at the load pulls whatever the source can deliver, so the source has to be limited or a fuse has to be in series.

Can it be used on a 5 V rail at 3 A continuously? Electrically yes. Thermally the 1.4 mm by 0.9 mm body has to get rid of 0.12 W, and at 85 degrees ambient that leaves little margin, so the board copper and the actual ambient have to be checked rather than assumed.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.