TPS22929DDBVR
Product Specifications
TPS22929DDBVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS22929DDBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS22929DDBVR 1.8 A load switch with quick output discharge and latching reverse current protection in SOT-23
The TPS22929DDBVR is a single channel load switch in a six pin SOT-23 with three things that matter: a controlled turn on, a 150 Ohm discharge resistor that pulls the output down when the switch opens, and a reverse current circuit that latches the switch off when the output is driven above the input. It is rated 1.8 A at 25 C from 1.4 V to 5.5 V, and it is the part a portable product uses when a rail has to be switched and then bled down before the next power up.
The switch itself is a P channel MOSFET with an on resistance of 115 mOhm at 5 V and 3.3 V, rising to 129 mOhm at 1.5 V. The reverse current comparator is the unusual feature: it does not merely block, it turns the switch off and keeps it off until the enable or the input is cycled, which is what a product needs when a rail can be back fed by an accessory and the switch must not sit in a half conducting state. Under voltage lockout turns the switch off when the input is too low to control the gate.
Key parameters taken from the TPS22929DDBVR document
| Input range | 1.4 V to 5.5 V |
| Continuous current | 1.8 A at 25 C, limited by the package and the on resistance at higher ambient |
| On resistance at 5 V | 115 mOhm typical and 150 mOhm maximum, with 175 mOhm printed over the full range |
| On resistance at 3.3 V | 115 mOhm typical and 150 mOhm maximum |
| On resistance at 2.5 V | 118 mOhm typical |
| On resistance at 1.5 V | 129 mOhm typical and 170 mOhm maximum |
| Quiescent current | 2.2 microamp typical and 10 microamp maximum at 5.25 V with the switch on |
| Off supply current | 1.0 microamp typical and 5.0 microamp maximum at 5.25 V |
| Turn on and rise | About 3.3 ms turn on and 3.7 ms rise into 10 Ohm and 0.1 microfarad at 5 V, with the values moving at 3.3 V |
| Turn off and fall | A few microseconds, because the 150 Ohm discharge resistor pulls the output down once the switch opens |
| Output pull down | 150 Ohm typical and 200 Ohm maximum, the quick output discharge path |
| Reverse current threshold | 77 mV of output above input, with a 10 microsecond response, and the switch latches off rather than resuming when the condition clears |
| Under voltage lockout | The switch is held off below the 1.4 V floor of the operating range |
| Enable | Active high, and it must not be left floating |
| Body and packing | SOT-23 DBV 6 pins, 3000 pieces on a large reel, minus 40 to plus 85 C ambient |
The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.
Where the numbers matter in a real build
The latching reverse current behaviour is the difference between this part and a plain load switch, and it changes how the firmware has to treat it. When the output is driven about 77 mV above the input, the comparator turns the switch off within 10 microseconds and holds it off. It does not return when the reverse condition clears, which is deliberate, because a rail that has been back fed is in an unknown state and the product should re sequence rather than resume. A processor that reads a rail monitor and sees it dead has to toggle the enable, and a board that ties the enable high permanently has to accept that the rail is gone until the input is removed.
The discharge resistor is the other half of that behaviour. A 150 Ohm path to ground pulls a 10 microfarad rail down with a time constant of 1.5 ms, which is fast enough for a reset sequence and slow enough not to damage anything. On a rail with 1000 microfarad the same resistor takes 150 ms, and a reset pulse shorter than that will release the processor while the rail is still falling, which produces a brown out rather than a reset. The value is fixed, so the board either lives with the time constant or adds its own discharge.
The current rating is a 25 C figure and the on resistance rows show what happens away from it. At 1.8 A through 150 mOhm the dissipation is 486 mW, which no six pin SOT-23 can hold at 85 C ambient without a copper area far larger than the land pattern. In practice this part carries an amp or so continuously and the 1.8 A is the pulse figure. A board that needs 1.8 A steady should be looking at a switch with a thermal pad, and the number on the front page should be read with the temperature derating in the same document.
The quiescent current is in microamps rather than nanoamps, which is fine for a product that runs from a wall adapter and marginal for one that runs from a coin cell. Two to ten microamps with the switch on and one to five microamps with it off is a real load on a 200 microamp sleep budget, and the discharge resistor adds nothing when the switch is on but draws whatever the rail holds when it is off. A product that measures its off state in single microamps should compare this part against the low leakage family before choosing.
- The latch behaviour after a reverse current event, since the switch stays off until the enable or the input is cycled.
- The discharge time constant against the output capacitance, because a reset pulse shorter than the fall time does not reset anything.
- The on resistance at the load current for a steady 1.8 A, which is a thermal question in a six pin body.
- The quiescent and off currents in microamps, which matter on a battery product.
- The under voltage lockout, which decides when the switch stops conducting as the rail decays.
- The enable pull, which has to be a real level and not a floating pin.
Which projects this part fits
This part fits portable industrial and medical equipment where a peripheral rail has to be switched and discharged, portable media players and point of sale terminals with a removable accessory that can back feed, GPS and camera products with a sensor rail that has to come up after the processor, and any board where an accessory connector can be driven by an external source. The SOT-23 body is the reason it appears on boards that were laid out before wafer level packages were available.
Questions that come up before a purchase order is released
Does the switch come back on by itself after a reverse current event?
No. The comparator latches the switch off and it stays off until the enable is cycled or the input supply is removed. That is a deliberate behaviour for a rail that may have been back fed, and the firmware has to treat a dead rail as a state that needs a re sequence rather than a transient.
What is the discharge resistor value and can it be changed?
It is 150 Ohm typical and 200 Ohm maximum, fixed inside the part. The only way to change the fall time is to change the output capacitance or to add an external discharge path, and an external path in parallel lowers the resistance and increases the current through the switch when it opens.
Can the part be used at 1.8 A continuously?
At 25 C with enough copper it can pass the current, but the dissipation at 150 mOhm is 486 mW and the ambient derating in the document is the limit. Most boards use it at a few hundred milliamps to an amp, and a board that needs 1.8 A steady should confirm the junction temperature with the actual copper area.
Is the enable active high or active low?
Active high on this part. It has no internal pull down strong enough to define the state, so the controlling signal has to be a real level at all times, including during reset. A floating enable is the most common cause of a rail that comes up when it should not.
What happens below 1.4 V input?
The under voltage lockout holds the switch off, so the load sees the discharge resistor rather than a partly enhanced switch. That is the behaviour that keeps a decaying rail from feeding a load at an unpredictable resistance.
How SUPERB handles this line
We supply the TPS22929DDBVR on original 3000 piece reels with the date code and marking recorded, and we can supply the latching and non latching members of the same family when a board changes its fault policy. The power management cross reference page lists the load switches by current, discharge and reverse protection, BOM shortage recovery covers the case where this body is short and a near equivalent has to be qualified, and kitting service is how we deliver these switches against a portable product build.