Contact Us

TPS22924DYZPR

Brand: Texas Instruments
Texas Instruments TPS22924DYZPR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS22924DYZPR — Power Management & Signal Chain | Superb Automation

TPS22924DYZPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS22924DYZPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS22924DYZPR: 2 A load switch with 18.3 mOhm on resistance, a controlled slew rate and quick output discharge

TPS22924DYZPR is a single channel load switch that puts a lithium rail onto a sub circuit with a slow, defined ramp and takes it off again in microseconds in a DSBGA (YZP) body of 6 pins. It switches 0.75 V to 3.6 V at up to 2 A with 18.3 mOhm on resistance at 3.6 V and 22.7 mOhm at 0.75 V, turns on in about 7.4 ms through a controlled gate ramp so the inrush into a discharged capacitor stays small, turns off in 2.5 us, and discharges the output through an internal 450 to 1400 ohm resistor once it is off. The body is 0.9 mm by 1.4 mm.

Order code and package

Ordering stringTPS22924DYZPR, the six bump DSBGA body on a 3000 piece large reel
Part markingDL on the body, which is a two character code rather than the full part number
BodySix bump DSBGA, 0.90 mm by 1.40 mm, 0.50 mm pitch, which is small enough to sit inside the footprint of the connector it feeds
MaterialRoHS compliant, tin silver copper bumps, moisture level 1 with unlimited floor life at 260 degrees
Temperatureminus 40 to 85 degrees, narrower than most of the parts around it and the first thing to check on an industrial board
Reel sizes3000 pieces on the R suffix large reel and 250 on the T suffix small reel, both carrying the same marking
FamilyThe D suffix marks this die. Earlier TPS22924 without the suffix has a different turn on behaviour, so the two are not interchangeable on a timing critical rail

Electrical parameters that decide the application

Input range0.75 V to 3.6 V, which covers a single lithium cell plus the low voltage rails derived from it, and stops short of a 5 V bus
Continuous current2 A maximum, with the on resistance quoted at 200 mA of test current rather than at the full rating
On resistance18.3 mOhm at 3.6 V, 18.5 at 2.5 V, 19.6 at 1.8 V, 19.4 at 1.2 V, 20.3 at 1.0 V and 22.7 at 0.75 V, all typical, with maximum values roughly 25 per cent higher
Turn on time7.4 ms at 3.6 V and 6.3 ms at 0.9 V, measured into a 10 ohm load with a 0.1 uF capacitor
Output rise time6.2 ms at 3.6 V and 3.2 ms at 0.9 V, which is the number that sets the inrush into a real capacitor bank
Turn off time2.5 us at 3.6 V and 12 us at 0.9 V, fast enough to isolate a fault before a downstream part sees it
Output discharge450 to 1400 ohm internal resistor, active while the switch is off, so a rail does not float at a residual voltage after shutdown
Gate driveAn internal charge pump biases the NMOS switch, which is what keeps the on resistance flat down to 0.75 V instead of rising as the rail falls
Control inputLow threshold, so a 1.2 V or 1.8 V logic output can drive the ON pin without a level shifter
Leakage0.1 uA maximum on the ON pin from 0.9 V to 3.6 V or to ground, so the control line does not load the processor pin that drives it
Dissipation810 mW at 25 degrees on a high K board, derated by 8.1 mW per degree, which leaves 324 mW at 85 degrees
ESD5000 V human body model and 1000 V charged device model, tested per JESD 22

Family variants and how they differ

Why the on resistance rises at low voltageThe switch is an NMOS device and the gate has to sit above the source to keep it in enhancement. The internal charge pump generates that bias from the input, and at 0.75 V the pump has less to work with, so the gate overdrive falls and the resistance climbs from 18.3 to 22.7 mOhm
Controlled slew against a fast switchA fast load switch produces a current step equal to the capacitance times the rate of voltage change. At 6.2 ms for a 1.8 V rail the average inrush into 10 uF is under 3 mA, against hundreds of milliamps if the same bank were switched in a microsecond
Quick output dischargeThe internal resistor pulls the rail down after the switch opens, which matters on a bus that is shared with a part that must not see a residual voltage. It is also a load on any rail that has to be held up by another source after the switch opens
No current limitThis part has no programmable or fixed current limit. Its protection is the on resistance and the thermal path, so a hard short on the output is a thermal event rather than a limited one, and the switch must be turned off by the system
No reverse blockingThere is no reverse current protection. If the output is held above the input by another source, current flows back through the body of the switch and the part does not stop it
Thermal reality at 2 AAt 2 A and 18.3 mOhm the switch dissipates 73 mW, well inside the 324 mW available at 85 degrees. The dissipation only becomes the limit when the part is asked to carry a fault current rather than a load

Points to check before this part goes on a BOM

The 2 A rating is a continuous current, not a current limit. The part has no current limit at all, so a short on the output is limited only by the source impedance and the switch resistance, and the system has to turn the switch off.

The temperature range stops at 85 degrees, which is narrower than the 125 degree parts used on the same boards. An industrial board that has qualified the surrounding parts to 105 or 125 degrees still has to treat this one separately.

On resistance is quoted at 200 mA and rises about 25 per cent at the maximum value. A 2 A load at the top of the resistance window dissipates roughly 113 mW rather than the 73 mW the typical figure suggests.

The 7.4 ms turn on time is long by load switch standards and is the point of the part. A rail with a large ceramic bank that has to come up without pulling a spike from a battery needs that ramp, and a faster switch in the same socket will trip the battery protection.

The quick output discharge resistor is between 450 and 1400 ohm, which is a wide window. On a rail that has to decay within a specified time before the next power up, that window is the tolerance and not a fixed value.

There is no reverse current blocking. A rail that can be back fed from an external connector, a battery charger or a second supply needs a separate ideal diode or a switch with reverse protection.

What a controlled ramp does for a battery rail

A discharged ceramic bank looks like a short at the instant a switch closes. The current that flows is set by the rate at which the switch allows the voltage to rise, and the battery protection circuit sees that current as a load step. On a phone with a 2 A battery FET, a load switch that closes in a microsecond can trip the protection and take the whole board down.

Spreading the same transition over several milliseconds keeps the current inside what the battery can deliver. The cost is a rail that takes milliseconds to come up, which is acceptable for a sub circuit and not acceptable for a rail that has to be ready before the processor leaves reset. That is why the turn on time is the first number to check when a load switch is chosen for a board.

Where this order code fits

Rails that are switched on and off under software control inside a phone, tablet, camera, GPS receiver or portable instrument, and any sub circuit that has to be isolated while the rest of the board stays alive. The 7.4 ms ramp is the reason it suits a rail feeding a large ceramic bank, where a fast switch would pull a current spike out of the battery that the system cannot supply. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Is there a current limit on this part? No. Protection comes from the on resistance and the thermal path, so the system has to turn the switch off when a fault is detected rather than relying on the switch to limit it.

How fast does the output come up? About 7.4 ms at 3.6 V into a 10 ohm load with a 0.1 uF capacitor, with a 6.2 ms output rise time. The ramp is deliberate and is what keeps the inrush into a ceramic bank small.

Does it block reverse current? No. A rail that can be held above the input by another source will push current back through the switch, so a back fed rail needs a separate blocking device.

What logic level does the ON pin need? The control input has a low threshold so that 1.2 V and 1.8 V logic can drive it directly, and its leakage is under 0.1 uA so the processor pin is not loaded.

Can it switch a 5 V rail? No. The absolute input range stops at 3.6 V, and the on resistance is specified only up to that point. A 5 V rail needs a different member of the family.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.