TPS22918DBVR
Product Specifications
TPS22918DBVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS22918DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS22918DBVR: 5.5 V, 2 A load switch, 52 milliohm, adjustable rise time and quick output discharge
TPS22918DBVR is a single channel load switch with an N channel FET of 52 milliohm on resistance, a rise time set by an external capacitor and a configurable quick output discharge in a SOT-23 body of 6 pins. The switch is controlled by an on and off input that works directly from a 1 V GPIO, which means it can sit behind a modern microcontroller pin without a level shifter. The rise time is set by a capacitor on the CT pin, so the inrush into a large bulk capacitance is controlled by a component rather than by the silicon.
Order code and package
| TPS22918DBVR | Active, SOT-23-6, 3000 pieces on a large reel, NIPDAU or SN finish, MSL-2-260C with a one year floor life, marking 13MW |
| TPS22918DBVT | Active, 250 pieces on a small reel, the same body and marking |
| Package size | 2.9 mm by 1.6 mm, six pins, leaded body so the solder joints can be inspected |
| Ambient range | minus 40 to 105 degrees, which is an ambient rating |
| Body style | leaded SOT-23 rather than a chip scale package, chosen where visual inspection of the joints matters |
Electrical parameters that decide the application
| Input voltage | 1 V to 5.5 V |
| Continuous current | 2 A maximum |
| On resistance | 52 milliohm typical at 5 V, 53 milliohm typical at 3.3 V |
| Quiescent current | 8.3 microamp typical at 3.3 V |
| Control threshold | works from a 1 V GPIO, so no level shift is needed |
| Rise time | set by a capacitor on the CT pin |
| Quick output discharge | configurable through the QOD pin and an external resistor |
| ESD | plus or minus 2 kV human body model, plus or minus 1 kV charged device model |
Family variants and how they differ
| CT pin | sets the slew rate of the gate, so the inrush into the load capacitance is a component choice rather than a fixed number |
| QOD pin | pulls the output down through an external resistor when the switch turns off |
| ON pin | 1 V threshold, compatible with a low voltage GPIO |
| Body | SOT-23-6 leaded package, no thermal pad |
| Family | the same silicon appears in smaller bodies for boards that do not need inspection |
Points to check before this part goes on a BOM
Fifty two milliohm is quoted at 5 V and it rises at lower input. At 3.3 V the figure is 53 milliohm, and at 1.2 V it climbs towards twice that. On a 2 A load the difference between 52 and 100 milliohm is 0.19 W, which in a six pin body is a real temperature rise. The current rating is available at 5 V, not across the whole range.
The CT capacitor is the inrush control. With no capacitor the switch turns on in microseconds and the load capacitance draws a current limited only by the source impedance, which drags the main rail down and can reset everything else on the board. A capacitor on CT slows the gate and turns the inrush into a controlled ramp. The value depends on the load capacitance and the droop the supply can tolerate, so it cannot be copied from another board.
Quick output discharge needs an external resistor. The QOD pin does not pull the output to ground by itself; it connects the output to the pin, and a resistor from there to ground sets the discharge current. Without the resistor the pin does nothing, which is a common assembly mistake on a board where the function was assumed to be internal.
Eight point three microamp is the on state current. That is high for a switch that is supposed to be transparent on a battery rail. For a load that is switched on for minutes at a time it is irrelevant; for a rail that is left on for months the switch itself becomes part of the sleep budget, and a smaller quiescent part or a direct connection is the better answer.
A one volt control threshold is the reason this part exists. A microcontroller running from 1.8 V cannot drive the gate of a P channel switch directly without a level shifter. This part accepts 1 V as a valid high, so the GPIO drives it directly. The threshold is specified over temperature, which matters at 105 degrees ambient where leakage would otherwise pull a marginal input low.
One hundred and five degrees ambient is a generous rating for a leaded body. That is above the 85 degree limit of most parts in this class, and it comes from the package rather than from the silicon. A board in a sealed enclosure near a power stage can use it where a chip scale part would be outside its range.
Two amps is a thermal limit as much as an electrical one. At 2 A and 52 milliohm the switch dissipates 0.21 W. In a SOT-23 with no thermal pad that is a junction rise of roughly 50 degrees per watt times the area available, so the board copper under the part is part of the current rating. A short, wide trace into the switch matters more than the trace length.
MSL-2 with one year floor life applies here. The leaded body absorbs moisture like any plastic package. After 168 hours out of the bag it needs a bake before reflow. A reel from a broker that has been open for months is a delamination risk that shows up after assembly rather than during incoming inspection.
The switch does not block reverse current. When the output is held above the input by another source, the body diode conducts. That is fine for a rail that is only ever driven from the input side, and it is a problem for a board where a second supply can back feed the rail. In that case a switch with reverse blocking, or a series diode, is needed.
What to confirm before this part goes on a purchase order
Confirm the load capacitance and the supply droop the board can accept, because those two numbers decide the CT capacitor and the part cannot be qualified without them.
Ask for the date code and the packing. The body is published on a 3000 piece large reel, so a prototype quantity means a broken reel, and the moisture sensitivity means the seal date matters as much as the part number.
Where this order code fits
It switches a 2 A branch of a 3.3 V or 5 V rail on and off under a 1.8 V GPIO, with a rise time slow enough that the bulk capacitors do not pull the main rail down. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Does the switch limit current by itself? No. There is no current limit in this part, only the on resistance. A short at the load pulls as much current as the source can deliver, so the source supply has to be current limited or a fuse has to be in series.
How do I set the rise time? With the capacitor on the CT pin. A larger capacitor slows the gate and reduces the inrush. The value is chosen from the load capacitance and the droop the rail can tolerate, and the data sheet gives the curve rather than a single number.
Can it be used on a 1.2 V rail? Yes, the input range starts at 1 V. The on resistance at 1.2 V is higher than the 52 milliohm quoted at 5 V, so the current rating has to be rechecked for the voltage the board actually uses.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.