Contact Us

TPS22915CYFPR

Brand: Texas Instruments
Texas Instruments TPS22915CYFPR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS22915CYFPR — Power Management & Signal Chain | Superb Automation

TPS22915CYFPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS22915CYFPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS22915CYFPR: 5.5 V, 2 A load switch with 37 milliohm on resistance and quick output discharge

TPS22915CYFPR is a single-channel load switch with a controlled slew rate, a 2 A rating and an integrated output discharge path in a DSBGA (YFP) body of 4 pins. It connects a 1.05 V to 5.5 V rail to a load through 37 milliohm, ramps the output in about 900 microseconds so inrush stays under control, and pulls the output down through 143 ohm when the enable pin goes low.

Order code and package

Ordering stringTPS22915CYFPR, YFP package, 4-ball wafer level chip scale, tape and reel
Family membersTPS22914B and TPS22915B (fast slew), TPS22914C and TPS22915C (slow slew), the 15 parts add discharge
Package0.74 mm by 0.74 mm, 0.4 mm pitch, 0.5 mm height, four balls
Ambient range-40 C to 105 C
Pin count checkVIN, VOUT, ON and GND
Assembly noteA 0.4 mm pitch body needs a laser cut stencil and a reflow profile checked against the ball collapse

Electrical parameters that decide the application

Input range1.05 V to 5.5 V
On resistance37 milliohm typical at 5 V, 38 at 3.3 V, 43 at 1.8 V
Current rating2 A maximum continuous switch current
Quiescent current7.7 microamp typical at 3.3 V
Rise time913 microsecond typical at 3.3 V for the C grade, 64 microsecond for the B grade
Turn on and off1300 microsecond turn on and 2 microsecond turn off at 5 V for the C grade
Discharge143 ohm pull-down on VOUT when the switch is off, 15 parts only
Control thresholdLow enough to be driven from a 1 V GPIO
ESD2 kV HBM and 1 kV CDM

Points to check before this part goes on a BOM

The C suffix and the B suffix are the same silicon with different slew rates, and the difference is the whole reason to pick one. At 3.3 V the C grade ramps the output in 913 microsecond against 64 microsecond for the B grade, so a 100 microfarad load capacitor draws roughly 360 mA of inrush with the C part and about 5 A with the B part. A 2 A switch that sees 5 A of inrush trips or droops the upstream rail, so the slow grade is the safe default for a bulk capacitance above 10 microfarad.

Conduction loss at 2 A is 0.148 W through 37 milliohm, and at 1 A it is 0.037 W. In a 0.74 mm square body the only heat path is the four balls and the copper under them, so the 2 A rating is a statement about the die and not about a board with 5 mm of trace. A 0.148 W load in a 70 C enclosure needs the two power balls tied to a real plane, and the usual failure is a switch that works on the bench and drops out in a cabinet.

The 1.05 V minimum input is what makes this part interesting for modern rails. Many load switches stop at 1.8 V, so a 1.2 V core rail cannot be switched at all, and a discrete P-channel FET needs a gate drive below the rail. At 1.2 V the on resistance is higher than the 37 milliohm headline, and the data sheet curve shows roughly 70 milliohm at 1.05 V, which at 2 A is 0.28 W, so the same switch is a different thermal problem on a low voltage rail.

Quick output discharge is a feature with a side effect. The 143 ohm pull-down empties a 100 microfarad load to 5 percent in about 4.5 ms, which guarantees the load starts from zero on the next enable, and it also means the switch cannot be used to isolate a rail that has to hold charge, such as a backup capacitor or a supercapacitor. The 14 parts without discharge are the choice for those rails.

The 7.7 microamp quiescent current matters in a product that stays in standby with the rail enabled. Over a year that is 67 mAh, and it is drawn from whatever rail is being switched, so a 5 V accessory rail left on through a phone charger spends more than a small battery holds. The enable pin threshold is low enough for a 1 V GPIO, so the host can switch the rail off completely rather than relying on the load's own standby mode.

The four-ball package has no lead frame to inspect and no way to probe. The failure modes are a cold ball on the ground or input corner, which shows as reduced current capability, and a void under the output ball, which shows as heat. Both are invisible to a functional test at 100 mA, so a first article inspection of this body should include an X-ray of the four joints rather than a continuity check alone.

Where this order code fits

It is used to switch a sensor rail, a camera module, a solid state drive supply or a USB port in phones, tablets, wearables, notebooks and portable instruments, where the rail has to be isolated to save standby current and the load capacitor has to be charged without a droop. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

What is the difference between the B and C grades? Slew rate only. The B parts ramp in about 64 microsecond at 3.3 V and the C parts in about 913 microsecond, which decides the inrush current a given load capacitor will draw.

Does the discharge resistor affect normal operation? No. The 143 ohm path is only connected when the switch is off, and it is present only on the TPS22915 parts, not on the TPS22914.

Can two of them be put in parallel for 4 A? Not safely. The two switches will not share current evenly because their on resistances differ by part and by temperature, and there is no current limit or balancing built in.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.