Contact Us

TPS22915BYFPR

Brand: Texas Instruments
Texas Instruments TPS22915BYFPR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS22915BYFPR — Power Management & Signal Chain | Superb Automation

TPS22915BYFPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS22915BYFPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS22915BYFPR: a 5.5 V, 2 A load switch with 37 milliohm on resistance and a 64 microsecond rise time

TPS22915BYFPR is a single channel load switch with an integrated N channel MOSFET and a controlled slew rate in a DSBGA (YFP) body of 4 pins. It passes up to 2 A from a 1.05 V to 5.5 V rail through a switch that measures 37 milliohm at 5 V, 38 milliohm at 3.3 V and 43 milliohm at 1.8 V, and it draws 7.7 microamp of quiescent current at 3.3 V. The B member ramps in 64 microsecond at 3.3 V, and the 15 in the string adds a 143 ohm pulldown that discharges the output when the switch is turned off.

Order code and package

TPS22915BYFPRDSBGA body of 4 pins measuring 0.74 mm by 0.74 mm on a 0.4 mm pitch with a 0.5 mm height, 3000 pieces on a large reel, tin silver copper finish, moisture level 1 at 260 C with unlimited floor life, marking S4, active status in the addendum dated 7 November 2025
TPS22915BYFPTthe same die on a 250 piece small reel, which is the string used for a handful of boards
TPS22914BYFPRthe same switch without the output discharge, marking S3, same body and same reel
TPS22915CYFPRthe slow ramp member with a 913 microsecond rise time at 3.3 V, marking S7, which is the version for a rail with a large bulk capacitor
Body size0.74 mm by 0.74 mm with a 0.4 mm ball pitch, which is small enough that the footprint is often the deciding factor rather than the electrical rating
Temperature rowsminus 40 C to 105 C on every row, which is narrower than the 125 C window of the regulators around it

Electrical parameters that decide the application

Input voltage1.05 V to 5.5 V, so the switch works on a 1.2 V core rail, a 1.8 V memory rail, a 3.3 V peripheral rail or a 5 V bus without a different part
Continuous current2 A maximum, with the on resistance and the package thermal path setting what is realistic at a given ambient
On resistance37 milliohm typical at 5 V, 38 milliohm at 3.3 V and 43 milliohm at 1.8 V, which is the figure that decides the voltage drop at 2 A
Quiescent current7.7 microamp typical at 3.3 V with the switch on and no load, and the maximum rows run from about 11 microamp to 13.5 microamp over the full temperature range
Rise time64 microsecond typical at 3.3 V on the B member, against 913 microsecond on the C member, which is the inrush difference between the two
Output dischargea 143 ohm pulldown from output to ground when the switch is off, present on the 15 members and absent on the 14 members
Control thresholdthe ON pin accepts a 1 V logic level, so a 1.2 V or 1.8 V general purpose output drives it without a level shifter
Enable currentthe ON pin draws a small leakage in both states, which is why a battery rail does not lose charge through the control pin
Protectionthere is no current limit and no thermal shutdown on this part, so a shorted output is limited by the source supply rather than by the switch
ESD2 kV human body model and 1 kV charged device model, per the JESD 22 tests quoted on the front page
Thermal paththe die sits in a 0.74 mm body with no thermal pad, so the copper under the four balls is the only heat spreader
Qualificationoperating range minus 40 C to 105 C ambient, with the electrical table specified over that window

Members of the same family and how they differ

TPS22914Bthe same 2 A switch without the output discharge resistor, marking S3, which is chosen where the rail is bled by its own load
TPS22915Bthis string, with a 143 ohm pulldown and a 64 microsecond rise time at 3.3 V
TPS22914C and TPS22915Cthe slow ramp members at 913 microsecond, used where the load capacitance is large enough that the fast ramp would pull the source down
Bodyall four members share the 4 pin YFP wafer chip scale body measuring 0.74 mm by 0.74 mm on a 0.4 mm pitch
Protectionthere is no current limit and no thermal shutdown, so the upstream supply has to limit the fault current
Controlthe ON pin works from a 1 V logic level, which is what allows a 1.2 V general purpose output to drive it directly
Temperaturethe family stops at 105 C ambient, so a board that runs its other regulators at 125 C is outside the window of this switch

Points to check before this part goes on a BOM

There is no current limit on this switch. The part is a pass element with a controlled ramp, not a protected switch. A shorted output pulls whatever the upstream supply can deliver, so the supply has to have its own limit or the board has to use a protected load switch.

The discharge resistor is the difference between the 14 and the 15. A 143 ohm pulldown removes a floating rail in a few milliseconds on a small capacitor, and on a rail with hundreds of microfarad it removes it in much longer. A rail that must collapse before a re power sequence needs a switch with a stronger pulldown.

The rise time protects the source, not the load. 64 microsecond is fast enough to keep the inrush inside what a small battery or a regulator can supply, and it is slow enough that a 10 microfarad load capacitor does not present a step. A larger capacitor on the load needs the C member at 913 microsecond.

The 2 A rating is a switch rating, not a thermal rating. At 2 A and 38 milliohm the part dissipates about 150 mW inside a 0.74 mm body, which lifts the junction well above the ambient. A continuous 2 A load in a warm enclosure needs the copper area checked rather than the datasheet rating quoted.

A 1 V control threshold is what makes it usable on a modern rail. A 1.2 V general purpose output drives the ON pin directly, and the switch does not need a level shifter or a pull-up to a higher rail, which is one of the reasons a 4 pin part is enough.

The package has no thermal pad. The four balls carry both the current and the heat, so the copper on the two power balls is the only path. A footprint that necks the power traces down to the ball pitch raises the resistance of the whole switch.

Where a 0.74 mm load switch is used

A solid state drive, a camera module or a wearable powers its rails down between bursts, and the switch is what makes that possible in a space that has no room for a larger part. The 7.7 microamp quiescent current is what allows the rail to stay off for days without the switch itself becoming the load.

The same part is used to sequence two rails at power up, because the ON pin can be driven from a power good signal or from a general purpose output with a delay. A 64 microsecond ramp at the second rail is short enough that the first rail does not see a step, provided the load capacitance is small.

Where this order code fits

a solid state drive, a camera module or a battery powered device that powers a rail up and down between bursts Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Does this part limit current? No. There is no current limit and no thermal shutdown. The switch passes what the source can deliver, so a shorted rail is protected by the upstream supply or by a fuse, not by this part.

What is the difference between the B and C members? The rise time. The B member ramps in 64 microsecond at 3.3 V and the C member in 913 microsecond. The C version is chosen when the load capacitance is large enough that the faster ramp would pull the source down.

Does the 15 discharge the output? Yes, through a 143 ohm pulldown when the switch is off. The 14 members do not have that resistor, which is the only difference between the two families.

Can it switch a 5 V rail from a 1.8 V control signal? Yes. The ON pin threshold is low enough for a 1 V logic level, so a 1.8 V output drives it directly and no level shift is needed.

What is the maximum ambient? 105 C, which is lower than the 125 C window of many regulators. A board that runs its regulators at 110 C ambient is outside the rating of this switch.

What packing does SUPERB quote for this string? 3000 pieces on a large reel with date codes, packing and country of origin on the offer, and a cut length is quoted as a cut length rather than as a reel.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.