Contact Us

TPS22860DBVR

Brand: Texas Instruments
Texas Instruments TPS22860DBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS22860DBVR — Power Management & Signal Chain | Superb Automation

TPS22860DBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS22860DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS22860DBVR ultra low leakage single channel load switch for battery and sensor rails in the 6 pin SOT-23

The TPS22860DBVR is a load switch built for the case where the current is small and the leakage is the whole problem. It is a single channel P channel switch rated 200 mA, with an input range of 0 V to the bias rail, an on resistance measured in hundreds of milliohms, and a leakage current in the low nanoamp range. It exists because a battery powered sensor node that sleeps for a year cannot afford a switch that draws a microamp while it is off.

The device needs a bias supply and a separate input. VBIAS powers the gate drive and can sit anywhere from 1.65 V to 5.5 V, while VIN is the rail being switched and can be anywhere from 0 V to VBIAS. That separation is what lets the part switch a 1.8 V sensor rail while its control side runs from a 3.3 V or 5 V housekeeping rail. The control input is active high and must not float, and the body is a six pin SOT-23 or SC-70, which is small enough to sit next to the connector it protects.

Key parameters taken from the TPS22860DBVR document

Input voltage0 V to VBIAS, so the switch can pass a rail that is below the bias supply
Bias voltage1.65 V to 5.5 V, the supply that runs the gate drive
Maximum continuous current200 mA, with 400 mA allowed in pulses shorter than 300 microseconds at 2 per cent duty
On resistance at 5 V0.73 Ohm typical with a 5 V bias, which is the number on the front page
On resistance at 3.3 V0.68 Ohm typical, and the electrical table prints 0.92 Ohm typical and 1.15 Ohm maximum for a 3.3 V bias at 25 C, rising to 1.31 Ohm over the full range
On resistance at 1.8 V0.63 Ohm typical on the front page, and 0.95 to 1.35 Ohm in the electrical table depending on temperature
VIN leakage2 nA, which is the figure that decides whether the part is usable in a coin cell product
Bias leakage10 nA at 5.5 V
Quiescent current10 nA typical and 100 nA maximum with the switch on and no load
Shutdown current10 nA typical and 100 nA maximum on both VIN and VBIAS with the enable low
Control input leakage2 nA typical and 50 nA maximum at 3 V, which is small enough to drive from a GPIO that is itself asleep
Turn on and turn off2 microseconds typical and 13 microseconds maximum to turn on, 3 microseconds typical and 15 microseconds maximum to turn off
Absolute maximum6.5 V on the bias and control pins, and 200 mA continuous through the switch
Body and packingSOT-23 DBV 6 pins, 2.8 by 2.9 mm, 3000 pieces on a large reel, minus 40 to plus 85 C
ESD2 kV human body model and 1 kV charged device model, which is the floor a production line expects

The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.

Where the numbers matter in a real build

The on resistance and the current rating are in tension, and the ratio is the first thing to check. At a 3.3 V bias the table prints around 0.9 to 1.3 Ohm, so 200 mA dissipates between 36 and 52 mW, and the SOT-23 body can take that. A load that draws 200 mA continuously through 1.3 Ohm at 85 C ambient is a different thermal question than the same load at 25 C, and the vendor's derating note says the maximum ambient has to be reduced when the dissipation is high. Most applications of this part draw tens of milliamps, where the resistance costs millivolts and the leakage is what matters.

The bias arrangement is where boards go wrong. VBIAS must be at or above VIN, because the gate drive is referenced to the higher of the two, and a board that ties VBIAS to a 1.8 V rail while switching a 3.3 V input is outside the recommended conditions even though nothing burns immediately. The part then fails to enhance the switch fully and the on resistance is far above the printed figure, which looks like a heat problem and is really a wiring problem. The safe pattern is to bias from the highest rail on the board and let the switch pass anything below it.

The leakage figures are the whole point, and they are also easy to lose in the rest of the circuit. Two nanoamps of VIN leakage and ten nanoamps of bias leakage are meaningless if the enable line has a 100 kOhm pull down to a rail that leaks a microamp, or if the load has a divider across it. A coin cell product that measures its sleep current in tens of microamps will not see this part at all, and one that measures in single microamps needs the pull down to be sized against the same budget. The switch is one term in that budget, and it is a small one.

The turn on time is microseconds, not milliseconds, which is unusual for a part this size and matters for a different reason. A switch that turns on in 2 microseconds into a capacitive load produces a current spike limited only by the load resistance and the switch, so a sensor rail with 10 microfarad of decoupling sees a hard step. There is no soft start and no controlled slew here. A product that needs a soft start on this rail has to add a series resistor or a different switch, because this part will deliver the inrush as fast as the load will take it.

  • The bias rail chosen for the gate drive, which has to be at or above the switched rail.
  • Sleep current measured with the enable held low and the load still connected, since the leakage of the load is often larger than the switch.
  • The pull down or pull up on the enable line, which must not float and must fit the same nanoamp budget.
  • Inrush into the decoupling on the switched rail, because the part has no soft start and turns on in microseconds.
  • Junction temperature at 85 C ambient with the actual load current, since 200 mA through an ohm is tens of milliwatts in a small body.
  • The pulse rating, 400 mA for under 300 microseconds at 2 per cent duty, if the load has a burst mode.

Which projects this part fits

This part fits wearables and sensor nodes where a rail has to be disconnected for a year of shelf life, internet of things modules with a 1.8 V sensor rail and a 3.3 V housekeeping rail, wireless sensor networks that wake on an interrupt and power the radio from a switched rail, and any board where the leakage of the switch has to be smaller than the self discharge of the cell. It is also the practical part when a board already uses a small P channel MOSFET plus two resistors and the board would rather have one component with a guaranteed leakage number.

Questions that come up before a purchase order is released

Can VBIAS be lower than VIN?

No. The recommended range for VIN is 0 V to VBIAS, and a bias below the input leaves the switch partly enhanced, with an on resistance far above the printed value. Bias the part from the highest rail available, which is usually the 3.3 V or 5 V housekeeping supply.

Is there a soft start?

No. The part turns on in 2 to 13 microseconds, which is fast enough to deliver the full inrush into a decoupling bank. If a rail needs a controlled rise, this is not the part, and the alternative is a switch with a slew rate control or a series resistor that is bypassed later.

What is the difference between the SOT-23 and the SC-70 versions?

Only the body. Both are six pin, both carry the same die and the same electrical limits, and the SC-70 is the smaller of the two at 2.1 by 2.0 mm. The choice is a board area question and, in some assembly flows, a visual inspection question, because the SOT-23 leads are easier to inspect.

Does the enable pin have an internal pull down?

Not a strong one. The input leakage is 2 to 50 nA, so the pin is high impedance and floats if nothing drives it. A processor pin that goes high impedance during reset will leave the switch in an undefined state, which is why a pull down to ground is part of the standard application.

Why is the on resistance higher than a power switch of the same current?

Because the part is built for leakage rather than conduction. A larger P channel would lower the resistance and raise the gate charge and the leakage. At 200 mA the resistance costs tens of millivolts, which is the trade the vendor made deliberately.

How SUPERB handles this line

We supply the TPS22860DBVR on original 3000 piece reels with the marking and date code recorded, and we can supply the SC-70 body of the same die when a board is area limited. The power management cross reference page lists the low leakage switches by current and body, BOM shortage recovery covers the case where this part is short and a near equivalent has to be qualified, and kitting service is how we deliver these switches with the rest of a sensor node bill of materials.