Contact Us

TPS2065DGNR

Brand: Texas Instruments
Texas Instruments TPS2065DGNR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS2065DGNR — Power Management & Signal Chain | Superb Automation

TPS2065DGNR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS2065DGNR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS2065DGNR: 1 A current limited power distribution switch, 70 milliohm, active high enable, HVSSOP-8

TPS2065DGNR is a current limited high side switch that connects a 2.7 V to 5.5 V rail to a load, reports a fault on an open drain pin and limits the current instead of letting a short pull the rail down in a HVSSOP-8 body of 8 pins. The switch is a 70 milliohm N-channel FET with an internal charge pump, so it works from a 2.7 V rail without a gate supply above the input. Current is limited to between 1.1 A and 1.9 A, rise time is about 0.6 ms, and the fault output is deglitched so a transient does not produce a false report. Standby current is 1 microamp maximum with the switch off.

Order code and package

TPS2065DGNRActive, HVSSOP (DGN) body, 8 pins, 2500 pieces on a 330 mm reel
TPS2065DGNR.AActive, same body and same 2500 piece reel, material row at MSL Level-1-260C-UNLIM
TPS2065DBVRActive, the five pin SOT-23 body with 3000 pieces, same silicon and same active high enable
TPS2061DGNRthe same switch with an active low enable, same body, the string to use when the control logic is inverted
Temperature rangeminus 40 to 125 degrees junction in the orderable table, with the electrical limits published over minus 40 to 85 degrees ambient

Electrical parameters that decide the application

Input voltage2.7 V to 5.5 V
Continuous current1 A per channel
On resistance70 milliohm typical in the D and DGN bodies, 95 milliohm at 3.3 V, 135 to 140 milliohm maximum in the small body
Current limit1.1 A minimum, 1.9 A maximum
Rise time0.6 ms typical, set internally with no external capacitor
Standby current1 microamp maximum with the switch off
Fault outputopen drain, deglitched, no false report during power up
Thermal shutdown135 degrees, recovery at 125 degrees, 10 degrees of hysteresis

Family variants and how they differ

TPS2065single switch, active high enable, the string on this page
TPS2061single switch, active low enable
TPS2062 and TPS2066two switches in one body, one enable each, same current limit per channel
TPS2063 and TPS2067three switches in one body for a multi port product
Enable logicthe 65 and 67 endings are active high, the 61 and 63 endings are active low

Points to check before this part goes on a BOM

The current limit window is wide on purpose, and a fuse calculation has to use it. The limit is specified from 1.1 A to 1.9 A, so the same part number can pass 1.1 A on one unit and 1.9 A on the next. A load that draws 1.2 A continuously will start on some units and trip on others, which is the classic field failure for this family. Size the load below 1 A and treat the limit as protection rather than as regulation.

Thermal shutdown only reacts under an overcurrent condition. The 135 degree trip is there to protect the FET while it is limiting current, not to protect it from a hot environment. A board that runs the switch at 1 A in a 70 degree cabinet relies on the copper, not on the protection, and the junction temperature has to be calculated from the on resistance and the actual current.

The fault output is deglitched for a reason. At power up, charging a heavy capacitive load looks like a short for the duration of the 0.6 ms rise. A part without the deglitching pulls the fault pin low on every power up and the controller reports an error that did not happen. With it, a host can distinguish an inrush event from a real short, which is what the interrupt is for.

Seventy milliohms at 1 A is 70 mV of drop and 70 mW of heat. The drop matters on a 3.3 V rail feeding a device with a 3.0 V minimum: 70 mV eats a third of the margin. The heat matters in the eight pin body, where 70 mW is easy, and in the five pin body at 3.3 V, where the resistance rises to 95 milliohm and the drop grows to 95 mV.

There is no reverse current blocking in this part. If the output is held above the input, for example by a charged capacitor on a load that stays powered from elsewhere, current flows back through the body diode. A board that needs true reverse blocking needs a different family, and a board that only needs to survive a brief back feed can accept this one with a note on the assembly drawing.

The enable pin is a logic input, not a soft start control. Rise time is fixed at about 0.6 ms and the charge pump handles the gate, so there is nothing to tune. Toggling the enable quickly does not produce a controlled ramp, and using it as a PWM input will exceed the switching capability of the charge pump and produce large current spikes.

A five pin and an eight pin body are both available and they are not footprint compatible. The DGN body brings out the fault pin and the second ground, the DBV body is smaller and drops the thermal pad. A board that needs the fault signal must use the eight pin body, and a board that swaps between them loses the fault report without any electrical warning.

Under voltage lockout keeps the switch off until the rail is usable. Below the lockout threshold the FET stays off and the output does not follow the input, which prevents a controller from starting on a rail that is still ramping. The threshold is fixed internally, so a 2.7 V rail at the bottom of its tolerance has to be checked against it rather than assumed.

Packing is 2500 pieces on a 330 mm reel for the DGN body. That is a large reel for a part used a few at a time on a board, and a small build of 200 pieces leaves most of a reel in stock with a moisture clock running. The five pin body ships 3000 on a 180 mm reel, which is easier to handle in small quantities.

What to confirm before this part goes on a purchase order

State the continuous load current and the ambient temperature. The current limit window is wide and the thermal calculation depends on the ambient, so a quote without both cannot be checked against the 1 A rating.

Say whether the fault output is used. If it is not, the five pin body is smaller and cheaper, and if it is, the eight pin body is the only option in this family.

Where this order code fits

It feeds a USB port, a card slot or a peripheral connector on a 5 V or 3.3 V rail, where a cable fault or a hot plug event has to be contained without dropping the main supply. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can two of these share one 5 V rail? Yes. Each switch limits its own channel and the fault outputs can be wired together if they are open drain, with one pull up. The sum of the two load currents still has to be inside what the upstream supply can deliver, because the switches limit but do not share current.

What is the difference between the 61 and 65 endings? The enable polarity. TPS2065 turns on with a high input and TPS2061 turns on with a low input, and the rest of the part is the same. Mixing them on one board is a common source of a rail that is on when the system thinks it is off.

Does the output rise smoothly into a large capacitor? Yes. The internal charge pump controls the gate so the output rises in about 0.6 ms regardless of the load capacitance, and the current limit caps the inrush at the same time. A 100 microfarad load therefore charges without the rail collapsing, which is the behaviour the part is sold for.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.