TPS2065CDBVR
Product Specifications
TPS2065CDBVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS2065CDBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS2065CDBVR: a 1.5 A fixed current limit power switch in a five pin SOT-23
TPS2065CDBVR is a power distribution switch with a fixed current limit, built for USB ports and other loads that see heavy capacitance and shorts in a SOT-23 (DBV) body of 5 pins. It is rated at 1.5 A of continuous output current with a fixed current limit window of 1.1 A to 1.96 A, and it works from a 5 V rail with reverse current blocking, a built in soft start and a deglitched fault output. The overcurrent response is 2 microseconds, the limit accuracy is plus or minus 20 per cent because the threshold is fixed inside the part, and the body is the 5 pin SOT-23 with marking VBYQ. The family is pin for pin across 0.5 A, 1 A, 1.5 A and 2 A members, and the parts are UL listed under file E169910.
Order code and package
| TPS2065CDBVR | the 1.5 A member in the 5 pin SOT-23 with marking VBYQ, which is the rating a single USB port or a downstream rail usually needs |
| TPS2041C and TPS2051C | the 0.5 A members, with an active high and an active low enable, which is the pair used on a port that has to be limited to 500 mA |
| TPS2061C | the 1 A member, which sits between the port rating and the 1.5 A part and is the choice for a load that bursts above 500 mA |
| TPS2069C and the 2 A members | the higher ratings in the same ladder, in the VSSOP and MSOP bodies, for a load that needs more than 1.5 A |
| -2 suffix | adds an output discharge, so a rail that has to fall quickly when the switch opens uses the -2 member rather than the plain one |
| Enable polarity | the ladder carries both polarities, so the enable signal decides the member as much as the current rating does |
Electrical parameters that decide the application
| Input voltage | a 5 V rail with tolerance, with the switch rated for the 5.5 V class of USB supplies |
| Load current | 1.5 A continuous for this member, with the current limit window from 1.1 A to 1.96 A setting the protection |
| Current limit accuracy | plus or minus 20 per cent, because the threshold is fixed inside the part rather than set by an external resistor |
| Response time | 2 microseconds typical from an overload to the switch entering current limit |
| On resistance | the resistance of the internal switch sets the drop at 1.5 A, and the data sheet gives it per body |
| Reverse current blocking | the switch blocks current from output to input while it is enabled or disabled, which protects a rail that stays biased after the switch opens |
| Soft start | built in, which limits the inrush into a heavily capacitive load such as a USB device with a large input capacitor |
| Fault output | open drain and deglitched, asserted on current limit and on overtemperature |
| Output discharge | present on the -2 members only, so a rail that has to be pulled down needs that suffix |
| Protection | current limit, thermal shutdown and undervoltage lockout, all internal |
| Temperature | minus 40 C to 85 C ambient, which is the window the electrical table is specified over |
| Approvals | UL listed and CB file E169910, which is what a product that ships into a safety review wants to see |
The family ladder and what the suffix changes
| TPS2065CDBVR | this order code, 1.5 A rated with a fixed current limit window of 1.1 A to 1.96 A, in the 5 pin SOT-23 with marking VBYQ |
| TPS2041C and TPS2051C | the 0.5 A members, which are the pair used on a port that has to be limited to 500 mA |
| TPS2061C | the 1 A member, for a load that bursts above 500 mA without needing the 1.5 A ceiling |
| TPS2069C and the 2 A members | the higher ratings in the same ladder, in the VSSOP and MSOP bodies |
| -2 suffix | adds output discharge, for a rail that has to fall quickly when the switch opens |
| Enable polarity | the ladder carries both polarities, so the control signal decides the member as much as the rating does |
| Approvals | UL listed under CB file E169910, which a safety review will ask for on a port switch |
Points to check before this part goes on a BOM
Plus or minus 20 per cent is a wide window and it is deliberate. A fixed threshold inside the part costs nothing to set and cannot be tuned, so the accuracy is whatever the silicon gives. On a USB port with a 500 mA host requirement and a 1 A connector, the 1.1 A to 1.96 A window of this member is above the requirement and above the connector rating at the top, which is why the 1 A member is usually the one chosen for that port.
The -2 suffix is the difference between a rail that falls and a rail that sits. A switch that opens into a load with a large capacitor leaves that capacitor charged, and a downstream device can stay half alive and hold a bus line. The discharge version pulls the rail down, which is what a product that has to re-enumerate a USB device needs.
Reverse blocking is not the same as reverse protection on the input. The switch stops current flowing from output to input. A reversed supply at the input still destroys it, and a connector that can be plugged in backwards needs a protection device ahead of the switch.
2 microseconds protects the trace, thermal shutdown protects the switch. In a dead short the switch sits at the limit current and heats until the thermal protection acts. The current the switch carries during that window is the limit, so the limit has to be inside what the body can dissipate continuously, not just briefly.
The UL listing is a document, not a claim. File E169910 is what a safety reviewer asks for, and having it on the part means the switch does not become the item that delays a certification. A substitute without the listing can cost more in review time than it saves in unit price.
Pin for pin across the ladder is a procurement advantage. The 0.5 A, 1 A and 1.5 A members share a footprint, so a product that changes its port rating does not change its board. That is also the risk: a substitution between members is invisible on the board and only visible in the current limit.
A USB port is a current limit problem before it is a power problem
A host port has to supply 500 mA and survive a device that tries to draw more, including a device with a large input capacitor that looks like a short at plug in. A switch with a 1.5 A limit, a soft start and a 2 microsecond response covers both cases, and the fault output tells the controller that a device has been removed rather than that the rail has failed.
On a product with several ports, the per port switch is also what keeps one faulty device from taking down the others. The upstream supply sees the sum of the port currents, and the fault output identifies which port caused the event, which is the difference between a support call and a diagnosis.
Choosing between the ladder members
The choice is made by the load current plus the connector rating, not by the supply. A 500 mA port uses the 0.5 A member so that the limit sits close to the requirement; a 1 A load uses the 1 A member; a load that bursts to 1.2 A uses the 1.5 A member. Picking a member two steps above the load leaves the trace and the connector unprotected, which is the mistake a fixed limit invites.
Where this order code fits
a USB host port, a downstream 5 V rail with a connector that can be shorted, or a peripheral slot that has to survive a device with a large input capacitor Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
What current limit does this member have? A fixed window of 1.1 A to 1.96 A against a 1.5 A continuous rating, with plus or minus 20 per cent accuracy because the threshold is internal.
Does it discharge the output when it opens? Not on the plain member. The -2 suffix adds output discharge, which is what a rail that has to fall quickly needs.
Is the enable active high or low? The ladder carries both, and this string is the active high member. The polarity is stated on the offer because it is the one pin that separates members that are otherwise pin for pin.
What approvals does it carry? UL listing under CB file E169910, which is what a safety review asks for on a USB port switch.
What happens during a short circuit? The switch limits the current within 2 microseconds, holds the limit while the fault lasts, and thermal shutdown protects the switch if the fault continues.
How does SUPERB keep these members apart? The exact ordering string, the current rating and the enable polarity are all stated on the offer with the date code and the packing, because the members are pin for pin and only the silicon inside differs.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Supplier Quality Audit page sets out the checks that keep a substitute from failing on the bench.