Contact Us

TPS2022DR

Brand: Texas Instruments
Texas Instruments TPS2022DR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS2022DR — Power Management & Signal Chain | Superb Automation

TPS2022DR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS2022DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS2022DR 1 A power distribution switch with an open drain overcurrent output in the 8 pin SOIC body

The TPS2022DR is the 1 A member of the TPS202x family, a high side switch with a current limit and, unlike the TPS201xA parts, an overcurrent logic output that a host can read. It sits in the same 8 pin SOIC body as the rest of the family and runs from 2.7 to 5.5 V, which makes it a 5 V and 3.3 V part at the same time. The reason boards still use it is the combination of a 1 A rating, a fault flag and a pinout that has not moved in twenty five years.

The part behaves like a fuse that resets itself. Above the current limit it holds constant current instead of opening, the overcurrent pin goes low while the condition lasts, and if the die gets too hot a thermal cut out opens the switch until it cools. The output stage is a 50 mOhm N channel MOSFET driven by an internal charge pump, so the switch works all the way down to 2.7 V without an external gate supply, and the rise and fall times are shaped to keep inrush into a capacitive load under control.

Key parameters taken from the TPS2022DR document

Rated current1 A maximum continuous load, between the 0.6 A and 1.5 A members of the same family
Short circuit limit1.1 A minimum, 1.5 A typical and 1.8 A maximum at 25 C with the output grounded
Headline limit1.5 A typical, which is the number in the family table and the one a first article usually measures
Input range2.7 to 5.5 V, with no external gate supply needed
On resistance33 mOhm typical at 5.5 V in on the feature list, and about 50 mOhm for the switch element in the electrical table at rated current
EnableActive low, so a grounded enable pin turns the switch on
Overcurrent outputOpen drain, active low, pulled down while the switch is in current limit or in thermal shutdown
Rise and fall time6.1 ms typical rise and 3.4 ms typical fall, set internally
Turn on delay20 ms typical into a 10 Ohm load with a 100 microfarad capacitor
Standby current10 microamp maximum with the switch off
ProtectionConstant current limit, thermal shutdown with automatic recovery, and an undervoltage lockout that holds the switch off until the input is valid
Reverse pathNo drain to source back gate diode, so the switch blocks both ways while off
BodiesSOIC 8 pins in the D package and 8 pin PDIP in the P package, with the R suffix marking tape and reel on the SOIC
TemperatureMinus 40 to plus 85 C ambient, junction to 125 C

The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.

Where the numbers matter in a real build

The overcurrent output is the reason to pick this part over the TPS2010A, and its polarity has to be handled correctly on a cold start. The pin is open drain and active low, so it needs a pull up to a rail that is present before the switch is enabled. If the pull up sits on the switched rail, the flag reads as asserted until the switch turns on, and firmware that counts fault events will log a fault on every power up. Pull it to the host rail and the behaviour is clean.

The current limit window is wide in absolute terms, 1.1 to 1.8 A around a 1.5 A typical, and the thermal consequence of the top of that window is what sizes the copper. At 1.8 A through a 50 mOhm element the part dissipates 0.16 W, which an SOIC 8 handles easily. The harder case is a sustained overload at exactly the limit, where the switch sits in constant current mode indefinitely and the die temperature depends on the thermal resistance of the board rather than on the electrical rating. An SOIC 8 with a small copper area reaches thermal shutdown at about 1 W of dissipation, so the short circuit current has to fall as the die heats, which is exactly what happens.

The turn on behaviour into a large capacitor is where this family differs from a modern load switch. A 20 ms turn on delay into a 100 microfarad load is slow, and it is deliberate, because a fast switch into a big capacitor pulls a current spike that trips the upstream supply. On a board that feeds a downstream module with its own bulk capacitance, this ramp is a feature. On a board that needs a rail up in under a millisecond, it is a problem, and the TPS2065D with its 2 microsecond overcurrent response and shorter ramp is the better fit.

The absence of a back gate diode has a second consequence that shows up in test. With two of these parts on one board, one feeding a rail that another device also drives, the switch that is off blocks the reverse path, so a rail can be held at a voltage the host does not expect. During in circuit test that reads as a stuck node. Add a bleed resistor on the switched side if the downstream load has no path to ground, otherwise the node holds its charge for minutes.

  • The overcurrent flag with the switch off, which must read as released rather than asserted on the chosen pull up rail.
  • Current limit into a real short, recorded as a number rather than as a pass or fail, since the window is 0.7 A wide.
  • Rise time into the actual output capacitor bank, as the 6.1 ms figure moves with load capacitance.
  • Junction temperature in constant current mode at the board's ambient, which decides whether the part hiccups or holds.
  • Reverse blocking with the switch off and the output driven by another source on the same rail.
  • On resistance as a voltage drop at the rated load, on three boards, since the SOIC lead frame dominates the spread.

Which projects this part fits

This part fits USB and peripheral ports on industrial and telecom boards, small motor and solenoid drivers that need a bounded stall current, sensor and radio module rails that have to be switchable with a fault report, and legacy boards in long production where the SOIC 8 footprint is fixed. It is also the natural choice where a host has one spare input and needs to know that a downstream load has failed, but where the load cannot justify a full hot swap controller.

Questions that come up before a purchase order is released

How fast does the flag respond to a short?

The switch enters current limit within microseconds and the flag follows, but the pin is meant for a host input and not for a hardware shutdown path. A hardware path needs the flag to drive a transistor that pulls the enable low, and that combination has to be checked for a race at power up. Most boards use the flag as an interrupt and let firmware decide.

Can two of these feed one rail for 2 A?

Not recommended. Two switches in parallel share current by their on resistance, and the one with the lower resistance carries more until it enters current limit, at which point it holds that current and the other takes the rest. The result is a rail that limits lower than the sum and a part that runs hot. Use a single higher current device instead.

Is the PDIP version still available?

The family lists both the SOIC and the PDIP in the same document, and the PDIP rows are the older material. Availability has to be checked per order code rather than assumed from the family, since the through hole rows are the ones that go obsolete first. We confirm the row on the current addendum before quoting.

What is the difference between the TPS2021 and the TPS2022?

The current limit. The TPS2021 limits at 0.9 A typical with a 0.6 A continuous rating, and the TPS2022 at 1.5 A typical with a 1 A rating. Everything else on the two parts is the same, including the pins, which makes them easy to confuse on a bill of materials and easy to substitute in an emergency if the load is checked.

How is the part tested at incoming inspection?

A functional test loads the output through a resistor chosen to sit just above the limit, confirms the flag asserts, then removes the load and confirms the flag releases. The actual trip current is recorded per lot, because the window is wide and a lot that sits at the low end will trip earlier than the customer's board expects.

How SUPERB handles this line

We supply the TPS2022DR on original reels with the lot and date code recorded against the delivery, and we can hold a buffer of the family's other members so that a change of rating does not become a change of supplier. The power management cross reference page groups the distribution switches by rating and enable polarity, BOM shortage recovery covers the case where the exact suffix is not on the shelf, and how to verify a drop in replacement sets out the tests we run before we offer a substitute.