Contact Us

TPS2000CDGNR

Brand: Texas Instruments
Texas Instruments TPS2000CDGNR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS2000CDGNR — Power Management & Signal Chain | Superb Automation

TPS2000CDGNR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS2000CDGNR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS2000CDGNR 1 A current limited power distribution switch in the 8 pin HVSSOP body

The TPS2000CDGNR is a single channel power distribution switch rated at 1 A, with a fixed current limit, reverse current blocking and a built in soft start, in the 8 pin HVSSOP package with an exposed pad. It is the active low enable member of the TPS20xxC family, which also covers 0.5 A, 1.5 A and 2 A parts in the same pinout. The intended load is a USB port or a peripheral rail where a heavy capacitive load or a short circuit is a normal event rather than an accident.

A power distribution switch is a different part from a load switch, and the difference is what happens during a fault. A load switch turns a rail on and off. This part limits the current to a fixed value, holds it there while the fault persists, and reports the condition on a fault pin. That behaviour is what lets a 5 V supply survive a shorted USB cable without collapsing the rest of the system, and it is why the family is specified with a two microsecond overcurrent response rather than only with an on resistance.

Key parameters taken from the TPS2000CDGNR document

Rated current1 A maximum operating current on this member, in a family that also covers 0.5 A, 1.5 A and 2 A
Current limit1.3 A minimum, 1.55 A typical and 1.8 A maximum on the 1 A member, with plus or minus 20 per cent accuracy and a constant current mode during a fault
Response time2 microseconds typical response to a short circuit
On resistanceSpecified per member, with the 1 A part in the tens of milliohms and the 2 A part at 72 to 98 milliohms in the DGN and DGK bodies
EnableActive low enable on this member, with the active high equivalent in the same family and the same pinout
Output dischargeNot fitted on this member, which is what separates it from the discharge members of the family
Fault reportingActive low open drain output, asserted during an overcurrent or an overtemperature condition, with a 9 ms deglitch
Reverse current blockingFitted, so a charged output does not feed back into a collapsed input
Soft startBuilt in, with controlled rise and fall times that limit the inrush into a capacitive load
Supply2.7 to 5.5 V, suited to the 3.3 V and 5 V rails
TemperatureMinus 40 to plus 85 C ambient
CertificationUL listed and CB file E169910
BodiesSOT-23 5 pins, VSSOP 8 pins and HVSSOP 8 pins with an exposed pad
Order code factsTPS2000CDGNR, HVSSOP DGN 8 pins, 2500 pieces on a large reel, NIPDAU finish, moisture level 2 with a one year floor life, minus 40 to plus 125 C

The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.

Where the numbers matter in a real build

The current limit is a window, not a number. On the 1 A member it sits between 1.3 A and 1.8 A, which means a load that draws 1.25 A continuously may or may not be inside the limit depending on the part. A product that needs a guaranteed 1.2 A should move to the 1.5 A member rather than rely on the top of the 1 A window. This is the most common mistake in a bill of materials built from a current rating alone.

The absence of output discharge is a feature, not an omission. On a rail that feeds a device with its own storage capacitor, a discharge resistor dumps that energy when the switch opens, which is good for a controlled power down and bad for a rail that has to hold its state. The members with discharge and without it share a pinout, so a board can change behaviour with a part number change only if the firmware and the load can tolerate both. We check which one a customer is actually ordering, because a distributor substitution between them changes the power down behaviour.

The 9 ms deglitch on the fault output is what keeps the signal usable. Without it, the fault pin would chatter during the current limit, and a controller polling it would see a burst of interrupts instead of one event. The trade is that a genuine short is reported 9 ms late, which for a USB port is well inside the time a host needs to react. A product that wants faster reporting has to look at the current monitor, not at the fault pin.

The exposed pad on the HVSSOP body is the thermal path and also the ground. On a board with a solid ground plane the pad is easy to solder and the thermal resistance is good. On a two layer board with a thin ground pour the pad can be the limiting factor at 1 A into a shorted load, because the part dissipates for as long as the fault lasts. The current limit holds at 1.55 A with an on resistance of about 100 milliohms, which is under 300 mW, so the part is comfortable unless the ambient is high and the board is closed.

  • Current limit window against the maximum load current, since the window is what the part guarantees rather than the rated figure.
  • Inrush into the real capacitive load, because the soft start sets the rise time and the host sees the resulting current.
  • Fault pin behaviour during a sustained short, including the deglitch time and the recovery path.
  • Reverse current behaviour when the input collapses with a charged output.
  • Dissipation during a sustained current limit at the highest ambient the product sees.
  • Which variant is fitted, with or without output discharge, since the two are pin compatible and behave differently at power down.

Which projects this part fits

This part fits USB ports and hubs on laptops and desktops, set top boxes, digital televisions, docking stations and any board that has to protect a 5 V or 3.3 V rail from a downstream fault. It also fits industrial equipment where a peripheral connector can be shorted by a user, and medical carts where a port has to survive a cable fault without taking the system down. Customers building a multi port product often use one part per port and a common fault line, because the open drain outputs can be wired together.

Questions that come up before a purchase order is released

How do I choose between the 1 A and the 1.5 A member?

By the maximum current the load can draw, compared against the current limit window rather than the rated current. The 1 A member limits between 1.3 A and 1.8 A, so a load that needs 1.2 A is inside its rating but at the edge of its limit. The 1.5 A member gives the same functional behaviour with a higher window, and the pinout is the same, so the choice is a part number and a recheck of the thermal path.

What is the difference between this and the 2001C?

Enable polarity and output discharge. The two parts are both 1 A members of the same family, share the body and the pinout, and differ in which enable level turns them on and whether the output is discharged when the switch is off. A board that has to hold a rail up during power down needs the member without discharge, and a board that has to bring a rail down quickly needs the other.

Does the part protect against a reverse connection?

It blocks reverse current, so a charged output does not feed back into a collapsed input. It is not a reverse battery protection device, and a product that can be connected backwards needs a series device or a diode in front of it. The distinction matters in a product with a user accessible connector, where a wrong cable is a realistic event.

Why does the fault pin need a pull up?

Because it is an open drain output. The pull up sets the logic level and the current, and it also sets how fast the line recovers after the fault clears. A 10 kOhm pull up to the controller rail is the usual choice, with a small capacitor if the line runs some distance. The pin can sink 10 mA, so a lower value is possible but rarely needed.

How is the part checked at incoming inspection?

Reel and moisture bag check, marking check, and a functional test on a board that applies a short, reads the fault pin and confirms recovery. The current limit can be measured on a sample by loading the output until the current flattens, which catches a mixed lot. Because the discharge and non discharge members are pin compatible, the test board should also confirm the power down behaviour so a substitution is caught before it reaches a line.

How SUPERB handles this line

We supply the TPS2000CDGNR from original reels with lot traceability, and we confirm the variant on the order because the discharge and non discharge members are pin compatible and easy to confuse. The power management cross reference page lists the power switch and protection families we carry, pin to pin cross reference covers the cross references between members of one family, and date code management is the page to read when a build has to be matched to a specific date code range.