TMS320VC5509APGE
Product Specifications
TMS320VC5509APGE
Texas Instruments — Power Management & Signal Chain
Product Overview
The TMS320VC5509APGE from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TMS320VC5509APGE: the 144-pin LQFP version of the 200 MHz C55x DSP
TMS320VC5509APGE is a fixed point digital signal processor in the smaller C55x package in a LQFP body of 144 pins. It is the same VC5509A device in the 144-pin LQFP: 200 MHz, 128K words of on-chip RAM, the USB full speed slave port and the asynchronous external memory interface. The PGE order code is the flat pack, which is the version a repair bench can rework.
Order code and package
| Order code | TMS320VC5509APGE |
| Package | 144-pin LQFP, PGE body |
| Packing | tray or reel according to the addendum line |
| Core | C55x fixed point DSP at 200 MHz |
| Memory | 32K words of dual access RAM and 96K words of single access RAM |
| Supply | 1.6 V core, 3.3 V input and output |
| Difference from GHH | flat pack body with seven general purpose pins instead of eight |
Electrical parameters that decide the application
| On-chip RAM | 128K words in total across dual access and single access blocks |
| External bus | asynchronous memory interface |
| USB | full speed 12 Mbit/s slave port |
| Serial | multichannel buffered serial ports and a host port interface |
| I/O | seven general purpose pins |
| Clock | phase locked loop with an external crystal |
| Boot | ROM loaders for host, serial and external memory boot |
Family variants and how they differ
| APGE | 144-pin LQFP, the part on this page |
| AGHH | 179-ball BGA with one more general purpose pin |
| VC5509 | the earlier member without the A suffix |
| VC5502 | the smaller memory member of the same generation |
Points to check before this part goes on a BOM
Choosing the flat pack over the BGA is usually a production and repair decision rather than an electrical one. The 144-pin LQFP can be replaced with hot air and inspected visually, and the 179-ball BGA cannot. For a product with a ten year service life that difference is worth more than the pin it gives up.
The core runs at 1.6 V at 200 MHz and the input and output rings at 3.3 V, with a specified power up order. The internal logic is fast enough that the supply decoupling is not optional: each supply pin needs its own capacitor close to the package, and a board that shares one capacitor across four pins will show jitter on the external bus.
The asynchronous external bus is what makes a boot from EPROM possible. The ROM loader reads the image over that bus with the wait states set by the boot table, so the EPROM speed has to match the setting. A faster EPROM is fine; a slower one boots into a fault that looks like a dead device.
The host port interface lets a microcontroller load the DSP and exchange data without sharing its bus. In legacy products that is the link to the system controller, and the protocol is often undocumented. A repair that replaces the DSP but not the controller sometimes fails because the controller's boot sequence expects the old revision's timing.
USB full speed at 12 Mbit/s is enough for a control and audio device and not enough for high rate streaming. The port is a slave, so it presents the product to a PC as a device. Products that need to record to removable media use the external bus and a separate controller instead.
The device is legacy and the supply is allocation driven. For a repair programme the question is not only whether the part can be bought but whether the revision matches. The C55x errata differ between revisions, and a firmware that was validated on one revision can show a timing fault on another in the external bus or the USB path.
Power consumption at 200 MHz is dominated by the core, and the C55x has idle modes that gate the clock to unused peripherals. A battery product should use them: the difference between full clock and an idle mode with the serial port live is large enough to change the runtime from hours to days, and the mode is set from firmware rather than by the board.
For a buyer, the practical step is to record the exact order code and the package, because the BGA and the flat pack are separate lines with separate availability. A support plan that assumes either can be substituted will fail at the first shortage, and the board cannot be converted between the two bodies without a new board.
The flat pack is the version that a repair bench can handle: hot air, visual inspection and a continuity check. That is worth more than the extra pin the BGA offers, and it is the usual reason a product with a long service life stays on the 144-pin body.
The asynchronous bus sets the boot time. A slow EPROM adds wait states to every fetch during the load, and a product that has a short power up window notices. The boot table carries the wait state setting, so the memory and the table have to be chosen together.
The core runs at 1.6 V and the input and output rings at 3.3 V, with a specified power up order. Each supply pin needs its own decoupling capacitor close to the package; sharing one capacitor across four pins produces jitter on the external bus that appears only at full clock and only on some boards.
The device is legacy and the supply is allocation driven. The practical plan for a supported product is a last time buy plus a documented alternative, because the alternative is a port to a different core generation and that is a firmware project rather than a part substitution.
The 144-pin flat pack has a 0.5 mm lead pitch and no thermal pad, so the heat leaves through the leads into the board. That makes the copper around the device part of the thermal answer, and it makes the package easier to inspect than the ball array version.
The host port interface on this device is the usual link to a system controller. In a repair, the controller side of that interface is as likely to be damaged as the DSP, so a board that fails to boot after a DSP replacement should have the host port lines checked before the new device is condemned. A support plan that covers the next decade should be built around spare boards rather than spare devices, because the flat pack can be replaced but the surrounding parts and the firmware tool chain are the items that disappear first, and a board in the store room is a known quantity where a loose device is not. The spares should be stored with their firmware version recorded, because a board that boots with an old image is still more useful than a bare device with no program.
Where this order code fits
It is used in legacy audio products, portable instruments and industrial boards where a flat pack package is easier to support in the field. Teams comparing it with a neighbouring part start from our MCU Cross Reference page, and teams replacing a part that has gone end of life start from the Obsolete Part Cross Reference Hub page.
Questions buyers ask
Is it the same silicon as the GHH part? Yes. The difference is the package and one general purpose pin, seven on the LQFP against eight on the BGA.
What core voltage does it need? 1.6 V for 200 MHz operation, with 3.3 V on the input and output rings.
Can it boot from an EPROM? Yes, through the asynchronous external bus using the loader in ROM. The wait states in the boot table have to match the memory speed.
Is a C55x device still buyable? It is listed, but supply is allocation driven and the aftermarket is the practical source. A last time buy quantity is the usual approach for a supported product.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Last-Time-Buy and LTB Planning page sets out the checks that keep a substitute from failing on the bench.