Contact Us

TMS320R2812GHHS

Brand: Texas Instruments
Texas Instruments TMS320R2812GHHS is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TMS320R2812GHHS — Power Management & Signal Chain | Superb Automation

TMS320R2812GHHS

Texas Instruments — Power Management & Signal Chain

Product Overview

The TMS320R2812GHHS from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TMS320R2812GHHS: 179 ball RAM based C28x DSP at 150 MHz, screened to 125 C

TMS320R2812GHHS is the 125 C version of the flashless 2812: 150 MHz C28x core, 20K words of single access RAM, a 16 channel 12 bit ADC and the external bus, with no program flash on the die in a BGA body of 179 pins. Same die, same 179 ball GHH body and same pinout as the A grade, with the S option moving the ambient range from minus 40 to 85 C up to minus 40 to 125 C. Code still arrives at reset through the boot ROM or the external bus, because there is no flash to hold it, so the loader in the production fixture is part of the build and not an accessory. Core supply is 1.9 V at 150 MHz, or 1.8 V if the PLL is kept at 135 MHz.

Order code and package

Order codeTMS320R2812GHHS
CoreTMS320C28x, 150 MHz, 6.67 ns
Package179 ball MicroStar BGA, body code GHH
RAM20K words single access
Flashnone
External buspresent
PWM16 compare channels, EVA and EVB
ADC12 bit, 16 channels
Core supply1.9 V at 150 MHz, 1.8 V at 135 MHz
I/O supply3.3 V
Temperatureminus 40 to 125 C, S option
DatasheetSPRS257C, revised June 2006

Electrical parameters that decide the application

Instruction cycle6.67 ns
Ambient rangeminus 40 to 125 C
Boot ROMon chip, samples the boot mode pins at reset
External interfaceprogrammable wait states, programmable strobe timing, three chip selects
Capture and encodersix capture inputs, two encoder interfaces
SerialSCI A, SCI B, SPI, McBSP, CAN
Digital I/O56 shared pins
Timersthree 32 bit CPU timers, four general purpose timers
PLLon chip, ratio can be changed at run time
Boundary scan1149.1 supported
Low powerindividual peripheral clocks can be disabled
Package thermal179 ball BGA, thermal vias under the die recommended

Points to check before this part goes on a BOM

At 125 C the RAM is the reliability question, not the flash, because there is no flash. The 20K words of single access RAM are specified over the extended range, but a board that runs the core at 150 MHz and 1.9 V in a hot enclosure has to check the derated timing and the refresh behaviour of anything it puts on the external bus, since the memory outside the die is usually the first part of the system to fall out of specification.

Core voltage at the top of the range has to be checked at the pin, not at the regulator. 1.9 V at 150 MHz gives very little headroom over the 1.8 V minimum, so a 100 mV drop across a connector or a long trace is enough to move the part outside its guaranteed operating point at 120 C, where the failure appears as corrupted arithmetic rather than as a reset.

The load at reset is a production step. On a 125 C board the loader has to work at temperature too, so the fixture that pushes code over the bus or through the boot ROM should be qualified in the same chamber as the board, otherwise the first units that fail are the ones that were never tested hot.

No flash also means no code security problem in the field. There is nothing on the die to read back, so a returned board cannot leak the program and a replacement does not need the customer's binary unless the loader itself is part of the program. That is a real advantage for contract builds where the firmware belongs to the end customer.

The external bus runs at 3.3 V and carries both code fetches and data. On a 125 C board the wait states have to be set for the slowest memory over temperature, and the bus has to be terminated well enough that the extra capacitance of a hot board does not turn a read into a marginal one. Three chip selects are available, which is usually one more than a loader plus a data memory needs.

The 12 bit ADC keeps sixteen channels, and the twin autosequencer lets the event managers trigger sampling at a fixed point in the PWM period. Over the extended range the offset drift is the number to watch: a current sense channel trimmed at 25 C will read several counts low at 110 C unless the trim is repeated at temperature or the measurement is made ratiometric to the reference.

Where this order code fits

Hot side control in drives and power converters, downhole and subsea instrument controllers, and any backplane board that sits in an enclosure without forced air and loads its program from the host at every power up. Boards comparing it with a neighbouring part start from our MCU Cross Reference page, and boards replacing a part that has gone end of life start from the Component Obsolescence Management page.

Questions buyers ask

Can the S grade drop into a board built for the A grade? Electrically yes, the die, the pinout and the peripheral set are the same. What has to be rechecked is the thermal path, the capacitor ratings and the voltage at the core pins, because those are the items that decide whether the 125 C rating is actually usable on that board.

Does the part need a flash programmer? No. There is no flash. Code is loaded at reset through the boot ROM or over the external bus, so the production fixture is a loader, not a programmer, and it has to be able to run at the temperature the board is specified for.

How much RAM is left for the application? The 20K words are shared with the stack, the loader and any buffers. A current loop with two axes and a modest parameter set fits; a data logger or a protocol stack usually has to go to external memory, which costs wait states on every access.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.