Contact Us

TMS320R2812GHHA

Brand: Texas Instruments
Texas Instruments TMS320R2812GHHA is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TMS320R2812GHHA — Power Management & Signal Chain | Superb Automation

TMS320R2812GHHA

Texas Instruments — Power Management & Signal Chain

Product Overview

The TMS320R2812GHHA from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TMS320R2812GHHA: 179 ball RAM based C28x DSP at 150 MHz, minus 40 to 85 C grade

TMS320R2812GHHA is a 150 MHz C28x core with no on chip flash: code is loaded from the host or from external memory at reset, which suits boards where the flash is a liability rather than an asset in a BGA body of 179 pins. The R2811 and R2812 are the RAM members of the 281x generation. There is no program flash on the die, so the memory system is 20K words of single access RAM plus the boot ROM, and the external memory interface is the path for both code and data on the R2812. The GHH body is the 179 ball MicroStar BGA with the external bus pinned out, and the A at the end of the code fixes the ambient range at minus 40 to 85 C.

Order code and package

Order codeTMS320R2812GHHA
CoreTMS320C28x, 150 MHz, 6.67 ns cycle
Package179 ball MicroStar BGA, body code GHH
RAM20K words single access, 16 bit
Flashnone, code is loaded at reset
Booton chip boot ROM, plus load over the external bus
External buspresent on the R2812, absent on the R2811
PWM16 compare channels across EVA and EVB
ADC12 bit, 16 channels
Core supply1.9 V at 150 MHz, 1.8 V at 135 MHz
I/O supply3.3 V
DatasheetSPRS257C, revised June 2006

Electrical parameters that decide the application

Instruction cycle6.67 ns at 150 MHz
Single access RAM20K words, 16 bit
Boot ROMyes, both devices
Event managersEVA and EVB, four general purpose timers, 16 compare channels
Capture and encodersix capture inputs, two quadrature encoder interfaces
ADC12 bit, 16 channels, twin autosequencer
SerialSCI A, SCI B, SPI, McBSP and CAN
Digital I/O56 shared pins
External interruptsthree
PLLon chip, dynamic ratio change supported
Boundary scan1149.1 supported on this family
Temperatureminus 40 to 85 C, A option

Points to check before this part goes on a BOM

No flash means the boot sequence is the first thing to get right. The boot ROM samples the boot mode pins at reset and either jumps to a loader or waits for a host, so a board that was built around an F2812 with code in flash needs a loader in the production fixture before the R2812 will run anything. Plan that fixture into the build, not into the debug phase.

Twenty thousand words of single access RAM is small next to the 128K words of flash on an F2812. A motor control loop, a current regulator and a small parameter set fit; a data logger, a protocol stack and a lookup heavy control law usually do not, and the overflow goes to external memory over the bus, where every access costs wait states.

The external interface is only on the R2812. The R2811 drops it, so the 128 pin PBK body has no way to fetch code or data from outside the die and therefore depends entirely on the boot loader path. Check the suffix before comparing prices, because the two devices are not interchangeable on a board.

Core voltage is 1.9 V at 150 MHz and 1.8 V at 135 MHz, and the two are not interchangeable. A regulator set for 1.8 V with the PLL programmed for 150 MHz is outside the specification even though the part often runs; the failure shows up as arithmetic errors under temperature rather than as a clean crash, which is the worst kind of fault to find in the field.

The 12 bit ADC has sixteen channels and a twin autosequencer, and on this generation the converter shares pins with the event manager captures. A board that uses all sixteen analogue channels gives up most of the capture inputs, so an encoder interface and a full analogue front end do not coexist on the same device.

The 179 ball BGA is a 0.8 mm pitch body in a package that needs the board to carry the thermal and the mechanical load. Inspecting joints under a 179 ball array is an X ray job, so incoming inspection on these parts has to include a sample X ray and a check of the date code and the moisture sensitivity label, which is what we do before a reel goes into a build.

Where this order code fits

Multi axis servo control, radar and sonar signal chains, telecom line card control, and any board where the code ships on a card or over a backplane and must not be readable from the processor. It is also the part chosen when a program has to be reloaded many times during a test or a calibration run without wearing flash. Boards comparing it with a neighbouring part start from our MCU Cross Reference page, and boards replacing a part that has gone end of life start from the Obsolete RF Part Replacement page.

Questions buyers ask

Can this part replace a TMS320F2812? Not directly. The F2812 carries 128K words of flash and boots from it; the R2812 has no flash and must be loaded at reset. The core, the peripherals and the pinout of the GHH body are the same generation, so the firmware port is short, but the boot path and the memory budget both change.

Why would a board use a part with no flash at all? Because the code is loaded fresh at every power up from a host, a card or external memory, so there is nothing on the die to wear out, nothing to lock down and nothing to read back. That suits backplane systems, test equipment and boards where the program changes often.

What is the difference between the GHH and ZHH bodies? Both are 179 ball MicroStar BGA bodies with the external interface. The Z prefix is the lead free package option in this family, so a board that has to meet a lead free assembly spec takes the ZHH code and the same part with the earlier finish takes the GHH code.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.