Contact Us

TMS320F2811PBKA

Brand: Texas Instruments
Texas Instruments TMS320F2811PBKA is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TMS320F2811PBKA — Power Management & Signal Chain | Superb Automation

TMS320F2811PBKA

Texas Instruments — Power Management & Signal Chain

Product Overview

The TMS320F2811PBKA from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TMS320F2811PBKA: 150 MHz C2000 with 128K flash and no external memory bus

TMS320F2811PBKA is a 32-bit fixed point control microcontroller in a LQFP body of 128 pins. It is the F2811 member of the C2000 family: 150 MHz, 128K by 16 bits of flash, 18K by 16 bits of SARAM, and no external memory interface, which is what separates it from the F2812. The PBKA order code is the 128-pin LQFP in the A grade.

Order code and package

Order codeTMS320F2811PBKA
Package128-pin LQFP, PBK body
Packingtray
Core32-bit C28x at 150 MHz, 6.67 ns instruction cycle
Memory128K by 16 flash, 18K by 16 SARAM, 1K by 16 OTP, 8K by 16 boot ROM
External busnone on this device number, the F2812 carries the interface
Temperatureminus 40 to plus 85 degrees Celsius on the A grade

Electrical parameters that decide the application

ADC12-bit, 16 channels, two sample and hold
Event managersEVA and EVB with 16 compare channels in total
Capture6 capture inputs and 2 encoder channels
SerialSCI A and B, SPI, McBSP, and one CAN controller
GPIO56 shared pins
Supply3.3 V input and output with a 1.8 V core
Timersthree 32-bit CPU timers and a watchdog

Family variants and how they differ

F281064K flash, 18K SARAM, 128-pin body
F2811128K flash, 18K SARAM, no external bus, the part on this page
F2812128K flash, 18K SARAM, with the external memory interface
A and S gradesminus 40 to 85 and minus 40 to 125 degrees respectively

Points to check before this part goes on a BOM

The F2811 and F2812 share a data sheet and a die but not a pinout or an external bus. The F2811 has no XINTF, so a product that expects to map SRAM, an LCD controller or a FPGA into the C2000 address space cannot use this device number at all. That is the first question to settle when a board is being quoted against an old drawing.

Two supply rails are required: 3.3 V for input and output and 1.8 V for the core, and the family data sheet specifies a power up order. A board that applies them in the wrong order can latch the device or draw unexpected current, and the reset circuit has to hold the part until both rails are valid. This is the main difference from the later single rail Piccolo parts.

The A grade in this order code stops at 85 degrees ambient. The S grade of the same device number covers 125 degrees. In a cabinet with a 70 degree internal ambient and no airflow, the junction rise over the package can consume the remaining margin, so the grade should be chosen from the measured internal temperature rather than from the room specification.

Flash is 128K by 16 bits and SARAM is 18K by 16 bits, which is smaller than the Piccolo parts that came later. A motor control application with a field bus stack, a point of load loop and a display menu can fill 18K of RAM when the stack is included, and the C2000 compiler's stack usage is not always obvious from the map file at first pass.

The 12-bit ADC has 16 channels on the 128-pin body and converts in the hundreds of nanoseconds at 25 MHz of ADC clock. Two sample and hold circuits allow simultaneous sampling of two channels, which is what makes three phase current sensing possible without a phase error between channels. Converted in sequence, the phase error appears as torque ripple.

This generation is old enough that the board around it matters for supply: the 1.8 V core rail is often a linear regulator or a dedicated switching part, and its ripple lands directly on the ADC reference through the die. Products that read the ADC at 12 bits need the reference and the core rail treated as analogue concerns, not as digital housekeeping.

The CAN controller inside this device is the older eCAN module, not the newer D_CAN instance. Driver code written for a later C2000 part does not port without changes to the register map, and a product that shares firmware across two C2000 generations should keep the CAN layer behind an abstraction rather than assume compatibility.

Long lead time is the practical risk on this generation: it has been in production since the early 2000s and demand comes from repair and legacy builds rather than new programs. A buyer supporting an existing product should record the exact order code and grade, because the same device number in a different temperature grade is a different line item and often a different lead time.

The event managers generate the PWM waveforms with a dead band and a trip input, and they run independently of the core. That independence is what makes a 150 MHz part usable for motor control: the waveform timing does not degrade when an interrupt is late, and the loop only has to update the compare values.

The 1.8 V core rail is a separate supply with its own decoupling, and its noise lands on the converter through the die. A board that feeds the core from a linear regulator off 3.3 V spends the difference as heat; a board that uses a switching regulator spends it as ripple. Both choices are valid and both need the reference and the core rail treated as analogue concerns.

The boot mode is set by pin states at reset, and the ROM loader then takes over the peripheral it was told to use. A board that is meant to boot from flash and is also reprogrammed over CAN needs a way to change those pin states, because the loader cannot be entered by a command once the part has started executing from flash.

The device has a code security module over flash, SARAM and OTP. Once the password is programmed, a device with a bad image cannot be erased without it, so a production fixture that locks parts should do it after the functional test rather than at the start of the cycle. A support plan for a product on this generation should record the exact order code, the grade and the packing, because those three fields together identify a line item that can be bought, and any one of them changed is a different part on the purchase order even when the silicon is the same.

Where this order code fits

It is used in legacy motor drives, inverters, power supplies and industrial controllers that were built around the F281x generation and are still in service. Teams comparing it with a neighbouring part start from our MCU Cross Reference page, and teams replacing a part that has gone end of life start from the Component Obsolescence Management page.

Questions buyers ask

Can it replace an F2812? Only on a board that does not use the external memory interface, and even then the pinout differs. The F2811 is the same core without XINTF, not a drop-in for the 176-pin F2812.

What is the difference between PBKA and PBKS? The temperature grade. PBKA is the A grade at minus 40 to plus 85 degrees, PBKS is the S grade at minus 40 to plus 125 degrees, both in the 128-pin LQFP.

Does it need both 3.3 V and 1.8 V? Yes. The core runs at 1.8 V and the input and output rings at 3.3 V, and the power up order in the data sheet has to be respected.

Is the part still available? It is listed as active in the current package addendum. Availability still comes from allocation rather than from a catalogue, so a support plan for an existing product should include a last time buy calculation.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Obsolete Part Cross Reference Hub page sets out the checks that keep a substitute from failing on the bench.