TMS320F2810PBKA
Product Specifications
TMS320F2810PBKA
Texas Instruments — Power Management & Signal Chain
Product Overview
The TMS320F2810PBKA from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TMS320F2810PBKA one hundred and fifty megahertz fixed point controller in a 128 pin package
The TMS320F2810PBKA is a fixed point digital signal controller from the F281x generation, running the C28x core at 150 MHz with 64K words of embedded flash and 18K words of static RAM. The 128 pin low profile quad flat pack measures 14 mm by 14 mm, and the package is the smallest body in the family that still carries the full peripheral set of the generation.
This is the device that started the C2000 line in a great many industrial products, and it is still bought for two reasons: the code base is already qualified, and the peripheral behaviour is well understood by the engineering team. The flash is 64K words on this member, split into two 8K word sectors plus the rest, and the RAM is made up of two 4K blocks, one 8K block and two 1K blocks. The order code ends in A for the minus 40 to plus 85 C grade.
Key parameters taken from the TMS320F2810PBKA document
| Core | C28x fixed point at 150 MHz, 6.67 ns cycle time, 16 by 16 and 32 by 32 multiply accumulate |
| Supply | 1.9 V core at 150 MHz and 3.3 V input output, 1.8 V core at 135 MHz |
| Flash | 64K words of embedded flash on this member, in two 8K word sectors plus larger sectors |
| RAM | 18K words of static RAM in five blocks, two of 4K, one of 8K and two of 1K |
| Boot ROM | 4K words |
| One time programmable memory | 1K words |
| Analog | 12 bit converter with 16 channels and an 80 ns conversion time |
| Event managers | two event managers, each with its own timers, comparators and PWM outputs |
| Serial | SCI, SPI, McBSP and CAN ports with boot support over the same interfaces |
| Address reach | 4M words of linear program and data space |
| Package | LQFP PBK, 128 pins, 14 mm by 14 mm |
| Order code facts | TMS320F2810PBKA, tray of 90, MSL Level-2-260C-1YEAR, minus 40 to plus 85 C, Active, marking 320F2810PBKA |
The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.
Where the numbers matter in a real build
The flash map is the constraint that bites late in a project. This member has 64K words, and the sector structure means a field update path that keeps a backup image needs a plan from the first day. A bootloader that copies an image into a second sector and then jumps to it is the usual approach, and it has to be sized against 64K words, not against the 128K words of the larger members of the same generation. A team that developed on the bigger part and then cost reduced to this one usually discovers that at exactly the wrong moment.
The RAM split matters for the same reason. 18K words is workable, but the blocks are not one continuous region, and the linker command file has to place the hot buffers in the block that suits the access pattern. On a motor control loop, a buffer that straddles blocks costs cycles, and at 150 MHz on a fixed point core there is no spare margin to absorb that.
The two event managers are the analog of the later PWM modules. Each has its own timers, comparators and output pins, which is how a three phase drive plus a second converter stage was built on this generation. A board that needs more than the two managers can provide has to move up the family, and that decision is a pin plan decision rather than a firmware one.
The 85 C upper limit is the industrial grade, and the .A row of the same order code in the vendor addendum is printed at 125 C. That inconsistency is worth resolving with the vendor or the distributor before a product that runs warm is committed, because the two numbers are not the same product. The moisture level is 2 with a one year floor life, which is more forgiving than the level 3 and 4 parts in this batch.
Boot ROM support over SCI, SPI, CAN and other interfaces is what makes a field update possible without a programmer. On a product that is already installed, that path is the difference between a service visit and a firmware download, so the boot mode pins have to be accessible and the protocol has to be documented as part of the product, not as a factory tool.
- The 128 pin body is the smallest in the family that carries the full set of event managers and serial ports, so it is the cost reduced member that still does the job.
- The 4M word linear address space covers program and data without paging, which keeps the compiler output simple on a fixed point core.
- The boot ROM covers the serial interfaces, so a field update can be done over the machine bus.
- The 90 piece tray is the published packing, and level 2 with a one year floor life allows a longer open time than the larger controllers in this batch.
- The marking 320F2810PBKA omits the TMS prefix, which is the quickest way to tell the vendor marked part from a re marked one on the bench.
The first article report should carry the flash programming time for the full array, the boot mode strap reading at each setting, and the converter linearity at both ends of its range. On a mature part these three checks catch almost every assembly fault early, and they cost less than a functional test that only exercises the application firmware. Record the readings in the traveler so that a second build can be compared against the first.
Which projects this part fits
Pump and fan drives, compressor controllers, welding supplies, uninterrupted power supplies, industrial inverters, battery chargers and legacy motion controllers are the applications where this part is still built in. It is also the part that appears when a qualified product needs a replacement for a member of the same generation that has become hard to buy. Our MCU cross reference lists what we hold against this generation, and the date code management page covers how a mature part is stored and rotated when the annual volume is small.
Questions that come up before a purchase order is released
Is the flash on this member really 64K words?
Yes. The vendor document states the F2810 has 64K words of embedded flash, split into two 8K word sectors plus the remaining sectors. The family document also describes members with 128K words, so a replacement study has to read the row for this code rather than the family headline.
What is the temperature grade on this code?
The addendum prints minus 40 to plus 85 C for the plain code and minus 40 to plus 125 C for the .A row of the same string. That has to be confirmed against the reel label for a product that runs warm, because the two rows are not interchangeable.
Can the device be programmed in circuit?
Yes, over the boot ROM interfaces and through the JTAG port. The boot mode pins select the interface, and the flash programming routine runs from RAM, so the in circuit path needs the boot pins to be accessible on the board.
How SUPERB handles this line
We supply the TMS320F2810PBKA in original trays with date code and lot traceability, and we confirm the temperature grade against the reel label rather than against the first row of the addendum. If a qualified product is running short of this part, send the annual volume and the firmware version and we will check what is available in the channel before a replacement study is started. Start from the last time buy and LTB planning page for the buffer decision on a mature device.