Contact Us

TLC6C598QPWRQ1

Brand: Texas Instruments
Texas Instruments TLC6C598QPWRQ1 is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TLC6C598QPWRQ1 — Power Management & Signal Chain | Superb Automation

TLC6C598QPWRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TLC6C598QPWRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TLC6C598QPWRQ1: eight channel shift register LED driver in a 16 pin TSSOP body, automotive qualified

TLC6C598QPWRQ1 is an eight bit serial in parallel out shift register whose outputs are low side DMOS sinks rated 40 V, built for driving LED strings from a serial bus with two clocks in a TSSOP body of 16 pins. The QPWRQ1 suffix is the automotive order code: AEC-Q100 qualified, temperature grade 1 from minus 40 to 125 C, HBM class H2 and CDM class C3B, in the 16 pin TSSOP on tape and reel. The logic runs from 3 V to 5.5 V while the drain outputs stand off 40 V, and each channel sinks 50 mA continuously or 200 mA in a single pulse shorter than 1 ms with the average held under 50 mA. Thermal shutdown trips between 150 and 200 C with 15 C of hysteresis.

Order code and package

Order codeTLC6C598QPWRQ1
Function8 bit serial in parallel out shift register, low side DMOS sink outputs
PackageTSSOP, 16 pins, body code PW, tape and reel
QualificationAEC-Q100 grade 1, HBM class H2, CDM class C3B
Logic supply3 to 5.5 V, 8 V absolute maximum
Drain rating40 V operating, 42 V absolute maximum
Output current50 mA continuous per channel at 5 V
Pulsed current200 mA single pulse under 1 ms, average under 50 mA
Thermal shutdown150 to 200 C trip, 15 C hysteresis
Input levels2.4 V high, 0.7 V low
Temperature rangeminus 40 to 125 C, grade 1
DatasheetSLIS142D, revision of September 2016

Electrical parameters that decide the application

On resistance, 5 V, 25 C6.7 ohm typical single channel, 9.6 maximum all channels
On resistance, 3.3 V, 25 C7.9 ohm typical single channel, 12.3 maximum all channels
On resistance, 5 V, 125 C9.1 ohm typical single channel, 14.5 maximum all channels
On resistance, 3.3 V, 125 C11.6 ohm typical single channel, 18.2 maximum all channels
Logic supply current0.1 microamp with outputs off, 160 microamps maximum with all on
Dynamic supply current200 microamps at 5 MHz clock into 30 pF
Off state drain leakage0.1 microamp at 25 C, 0.3 maximum at 125 C
Setup time15 nanoseconds, SER IN before SRCK rising
Hold time15 nanoseconds, SER IN after SRCK rising
Pulse duration40 nanoseconds minimum on SER IN
Output enableG active low, all drains off when high
ClearCLR active low, clears all registers

Points to check before this part goes on a BOM

The on resistance is not one number, it is four. A single channel at 5 V is 6.7 ohm typical and 9.6 maximum, all eight on at 3.3 V and 125 C reaches 18.2 ohm maximum. At a 20 mA sink that last figure is 364 mV of drop, so a 5 V LED string driven from a 5 V rail loses its headroom channel by channel as the board heats.

The 200 mA rating is a pulse rating with two conditions attached: the pulse must be shorter than 1 ms and the average must stay under 50 mA. A multiplexed display that scans at eight channels with a 12.5 percent duty can reach 200 mA per pulse, but a channel left on continuously at 200 mA is outside both the continuous rating and the average limit.

Thermal summing is arithmetic and worth doing before the board is committed. Eight channels at 50 mA into 14.5 ohm is 290 mW in the package, and the 16 pin TSSOP adds about 129 degrees per watt, which is a 37 degree rise. A cluster at 85 C ambient then runs the junction near 122 C, close enough to the 150 C shutdown floor to make the light flicker on a hot day.

Slow edges are a feature here and a trap as well. The drain rise and fall are in the hundreds of nanoseconds, which lowers radiated emissions, but the same slowness means the outputs cannot be used for a signal path and cannot be paralleled for higher current without accepting a shared transition.

CLR clears the shift register and the storage register together, so a firmware glitch on that pin blanks the whole chain rather than one channel. It is active low and carries no internal pull-up in the recommended arrangement, which is why a floating CLR is a common cause of a panel that shows nothing.

The logic supply and the drain supply are separate concerns on the same die. VCC is 3 to 5.5 V and the drains stand 40 V, but the on resistance rises as VCC falls, so a 3.3 V logic rail costs about 30 percent more drop than 5 V for the same channel current.

Where this order code fits

Automotive clusters and tell tale lamps are the target: one device drives up to eight indicator channels and cascades through SER OUT to the next device, so a cluster with twenty lamps needs three of them on one three wire bus. The 40 V drain rating also lets the same part drive a 12 V or a 24 V lamp rail while the logic stays on 3.3 V, which is why it turns up in appliance panels, elevator displays and PLC function indicators. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

How many channels can run at once? All eight, but the current per channel then sets the thermal limit. Eight at 50 mA is 400 mA of total sink and about 290 mW in the package at 125 C; a lower per channel current is the usual way to keep the junction under the 150 C shutdown floor.

Can the outputs drive a relay or a small solenoid? The part is a current sink with a 40 V standoff and no inductive clamp, so a coil needs a freewheel diode and a current under the 50 mA continuous rating. Most small relays draw more than that and belong on a dedicated driver.

What does the Q1 suffix buy over the commercial part? AEC-Q100 qualification and a grade 1 temperature range to 125 C, plus the packing and traceability that automotive customers require. The electrical function is the same eight bit shift register.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.