Contact Us

TLC6C5912QPWRQ1

Brand: Texas Instruments
Texas Instruments TLC6C5912QPWRQ1 is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TLC6C5912QPWRQ1 — Power Management & Signal Chain | Superb Automation

TLC6C5912QPWRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TLC6C5912QPWRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TLC6C5912QPWRQ1: twelve channel shift register LED driver in a 20 pin TSSOP body, automotive qualified

TLC6C5912QPWRQ1 is the compact version of the twelve bit LED shift register, same die and same 40 V outputs in a body a third of the area in a TSSOP body of 20 pins. The QPWRQ1 suffix is the 20 pin TSSOP on tape and reel with a device marking of 6C5912, automotive grade 1 from minus 40 to 125 C. The 0.65 mm pitch body takes roughly a third of the board area of the wide SOIC version, at the cost of a junction to ambient resistance of 114.8 degrees per watt against 81.2. Twelve outputs, 40 V drains, 50 mA continuous per channel and a 10 MHz serial clock are unchanged.

Order code and package

Order codeTLC6C5912QPWRQ1
Function12 bit serial in parallel out shift register, low side DMOS sink outputs
PackageTSSOP, 20 pins, body code PW, tape and reel, 2000 per reel
Device marking6C5912
QualificationAEC-Q100 grade 1, automotive order code
Logic supply3 to 5.5 V, 8 V absolute maximum
Drain rating40 V operating, 42 V absolute maximum
Output current50 mA continuous per channel at 5 V
Thermal resistance114.8 degrees per watt, PW body
Clock frequency10 MHz serial clock
Temperature rangeminus 40 to 125 C, grade 1
DatasheetSLIS141C, revision of July 2016

Electrical parameters that decide the application

On resistance, 5 V, 25 C6 ohm typical single channel, 9.6 maximum all channels
On resistance, 3.3 V, 25 C7.9 ohm typical single channel, 12.3 maximum all channels
On resistance, 5 V, 125 C9.1 ohm typical single channel, 14.5 maximum all channels
On resistance, 3.3 V, 125 C11.6 ohm typical single channel, 18.2 maximum all channels
Junction to case, top44.1 degrees per watt
Junction to board61.3 degrees per watt
Output enable delay210 nanoseconds low to high, 75 nanoseconds high to low
Cascade delay35 nanoseconds from SRCK falling to SER OUT
Drain rise and fall250 and 200 nanoseconds
Logic supply current0.1 microamp off, 170 microamps maximum all on
Setup and hold15 nanoseconds each on SER IN
Clock pulse width30 nanoseconds minimum high and low

Points to check before this part goes on a BOM

The smaller body is a thermal trade that has to be made deliberately. Twelve channels at 50 mA into 14.5 ohm is 435 mW and a 50 degree rise, so at 85 C ambient the junction is 135 C and at 105 C ambient it is 155 C, past the 150 C shutdown floor. The same board in the wide SOIC body survives the 105 C case, which is why the two order codes are not interchangeable on a hot board.

Junction to board is 61.3 degrees per watt against 44.1 to the case top, so most of the heat leaves through the pins into the board rather than off the top of the package. A ground pour under the body and thermal vias from the pad rows do more than any heatsink on the lid.

At 20 mA per channel the arithmetic becomes easy: 12 channels into 10.6 ohm typical at 125 C is 51 mW, a 6 degree rise, and the thermal question disappears. Most modern clusters run LEDs at 5 to 20 mA, which is exactly the range where this package is the right answer.

The 0.65 mm pitch is the assembly consideration. It reflows in the same pass as the rest of the board, but rework with a hand iron is difficult and a reflow profile that heats the board unevenly can lift a lead. Boards that are repaired in the field are better served by the wide SOIC order code.

Enable delay of 210 nanoseconds on and 75 nanoseconds off plus a 250 nanosecond drain rise means the output stage is slower than the serial bus by two orders of magnitude. A firmware change that relies on the bus speed for dimming resolution will not see any improvement, because the visible transition is set by the output stage.

Logic supply current with all outputs on is 170 microamps maximum at 5 V, and dynamic current at 5 MHz is 300 microamps. Those are logic figures only: the channel current flows from the drain supply through the LEDs and does not appear in VCC. A board that budgets VCC for the lamp current will over specify the regulator.

Where this order code fits

Space constrained cluster and switch panel boards where the twelve channels sit close to the LEDs and the harness is short. It is also the body used when the lamps are driven well below 50 mA, because the lower current keeps the thermal penalty of the small package inside the budget, which is the normal case for a modern cluster built from low current LEDs. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the Vendor Consolidation page.

Questions buyers ask

Can all twelve channels run at 50 mA at 105 C ambient? No. That is 435 mW and about a 50 degree rise, so the junction would pass the 150 C shutdown floor. The wide SOIC order code has 81.2 degrees per watt and does support it.

Is the TSSOP a drop in replacement for the SOIC order code? No. The footprint and the thermal resistance both change, and the body is much smaller. The electrical function is identical, so a board change is the only difference.

What is the practical current for a cluster LED? Between 5 and 20 mA in most cluster lamps. At 20 mA the twelve channels dissipate about 51 mW and the package rise is 6 degrees, well inside the grade 1 range.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.