Contact Us

TLC6C5912GQPWRQ1

Brand: Texas Instruments
Texas Instruments TLC6C5912GQPWRQ1 is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TLC6C5912GQPWRQ1 — Power Management & Signal Chain | Superb Automation

TLC6C5912GQPWRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TLC6C5912GQPWRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TLC6C5912GQPWRQ1: twelve channel shift register LED driver in a 20 pin TSSOP body, green automotive order code

TLC6C5912GQPWRQ1 is a twelve bit serial in parallel out shift register with 40 V low side DMOS outputs, the twelve channel member of the same family as the eight bit TLC6C598 in a TSSOP body of 20 pins. The G in this order code is the green material marking and the Q1 is the automotive qualification, on the 20 pin TSSOP in 2000 piece reels with a device marking of 6C5912G. Temperature grade 1 covers minus 40 to 125 C. Logic runs 3 to 5.5 V, the drains stand 40 V, and the package junction to ambient resistance is 114.8 degrees per watt, which is better than the SOIC body beside it in the same family.

Order code and package

Order codeTLC6C5912GQPWRQ1
Function12 bit serial in parallel out shift register, low side DMOS sink outputs
PackageTSSOP, 20 pins, body code PW, tape and reel, 2000 per reel
Device marking6C5912G
QualificationAEC-Q100 grade 1, automotive order code
Logic supply3 to 5.5 V, 8 V absolute maximum
Drain rating40 V operating, 42 V absolute maximum
Output current50 mA continuous per channel at 5 V
Thermal resistance114.8 degrees per watt, PW body
Clock frequency10 MHz serial clock
Temperature rangeminus 40 to 125 C, grade 1
DatasheetSLIS141C, revision of July 2016

Electrical parameters that decide the application

On resistance, 5 V, 25 C6 ohm typical single channel, 9.6 maximum all channels
On resistance, 3.3 V, 25 C7.9 ohm typical single channel, 12.3 maximum all channels
On resistance, 5 V, 125 C9.1 ohm typical single channel, 14.5 maximum all channels
On resistance, 3.3 V, 125 C11.6 ohm typical single channel, 18.2 maximum all channels
Output enable delay210 nanoseconds low to high, 75 nanoseconds high to low
Drain rise time250 nanoseconds
Drain fall time200 nanoseconds
Cascade delay35 nanoseconds from SRCK falling to SER OUT
Clock pulse width30 nanoseconds minimum high and low
Logic supply current0.1 microamp off, 170 microamps maximum all on
Dynamic supply current300 microamps at 5 MHz into 30 pF
Off state leakage0.1 microamp at 25 C, 0.3 maximum at 125 C

Points to check before this part goes on a BOM

Twelve bits cost one clock cycle per bit, so a full update is 12 clocks plus the register clock. At the 10 MHz rated clock that is 1.2 microseconds of serial time, which is far shorter than the 210 nanosecond output enable delay and the 250 nanosecond rise time that follow it. The visible transition is set by the output stage, not by the bus.

On resistance rises with temperature by about half again between 25 and 125 C: 9.6 ohm maximum becomes 14.5 ohm on a 5 V rail, and 12.3 becomes 18.2 on 3.3 V. At 20 mA the extra drop is 100 mV per channel, which is 2 percent of a 5 V LED string and enough to shift colour in a mixed white and amber cluster.

The slow output edges are the reason this family exists in a harness. A 200 to 250 nanosecond edge limits the harmonic content that leaves the cluster connector, but the same edge means the part is not usable as a logic buffer and cannot be paralleled to drive one higher current load without accepting that both channels turn on at slightly different times.

Cascading has a defined latency: data appears on SER OUT 7.5 clock periods after it enters SER IN, because the output is taken through a phase inverter. Firmware that shifts a 24 bit frame into two devices has to allow for that half period or the last bit of the frame lands in the wrong register.

The G marking identifies the green mould compound version, and the electrical limits are the same as the other Q1 order codes in this family. Mixing G and non G reels on one line is not a functional problem, but traceability for an automotive build normally keeps them separate.

With 114.8 degrees per watt, twelve channels at 40 mA into 14.5 ohm is 279 mW and a 32 degree rise. A cluster at 85 C ambient then holds a 117 C junction, inside the 150 C thermal shutdown floor but close enough that the shutdown margin should be checked with the real duty cycle rather than a nominal one.

Where this order code fits

Twelve channels map neatly onto a cluster segment or a bank of tell tale lamps, and the cascaded bus lets two devices cover twenty four indicators on three wires. Because the drains are rated 40 V the same part drives lamps from a 12 V or 24 V rail while the logic sits on the 3.3 V rail of the body controller, and the slow output edges keep conducted emissions low in a harness that runs behind the dashboard. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

How does this differ from the TLC6C598? Channel count and package. This one has twelve outputs in a 20 pin body, the 598 has eight in a 16 pin body, and both are the same shift register architecture with 40 V drains and 50 mA continuous sinks.

Can two devices share one serial bus? Yes. SER OUT feeds the next SER IN and both devices take the same SRCK and RCK, so 24 bits are clocked through in one frame. The catch is the 7.5 clock latency through each device, which the frame length has to account for.

What current can all twelve channels carry at once? 50 mA is the per channel continuous rating and there is no separate total current limit, so the package sets the answer: twelve at 50 mA into 14.5 ohm is about 435 mW and a 50 degree rise in the TSSOP body.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.