Contact Us

TLC352CD

Brand: Texas Instruments
Texas Instruments TLC352CD is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TLC352CD — Power Management & Signal Chain | Superb Automation

TLC352CD

Texas Instruments — Power Management & Signal Chain

Product Overview

The TLC352CD from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TLC352CD: dual differential comparator in an 8 pin SOIC tube, commercial grade, obsolete order code

TLC352CD is the tube packed commercial version of the dual CMOS comparator that replaces an LM393 pin for pin at a tenth of the supply current in a SOIC body of 8 pins. The D suffix is the 8 pin SOIC in tubes and the C grade runs 0 to 70 C. The two comparators draw 150 microamps typical and 300 maximum at 5 V, the inputs take 5 picoamps of bias current, and the output is an open drain n-channel sink that can be wired OR with the second channel. Response is 200 nanoseconds with 10 mV of overdrive. In the current packaging addendum this tube order code is listed as obsolete while the reel code beside it is active.

Order code and package

Order codeTLC352CD
Functiondual differential comparator, open drain output
PackageSOIC, 8 pins, body code D, tube
Lifecycleobsolete in the current packaging addendum
Active alternativeTLC352CDR, same die and body, 2500 piece reel
Supply range2.7 to 16 V, 18 V absolute maximum
Supply current150 microamps typical, 300 maximum for two comparators
Response time200 nanoseconds at 10 mV overdrive, 100 at 100 mV
Input offset voltage1 mV typical, 5 mV maximum at 25 C
Input bias current5 picoamps typical, 0.6 nanoamps maximum
Temperature range0 to 70 C, C suffix
DatasheetSLCS016B, revision of June 2025

Electrical parameters that decide the application

Input offset voltage1 mV typical, 5 mV maximum at 25 C, 6.5 mV over 0 to 70 C
Input bias current5 picoamps typical, 0.6 nanoamps maximum
Input offset current1 picoamp typical
Common mode range0 to VDD minus 1 V, VDD minus 1.5 V over temperature
Low output level150 mV typical, 400 maximum at 4 mA, 700 over temperature
Low level output current6 mA typical, 16 mA maximum at a 1.5 V drop
High level leakage0.1 nanoamps typical at 5 V
Supply current at 2.7 V65 microamps typical, 150 maximum
Response at 10 mV overdrive200 nanoseconds
Response at 100 mV overdrive100 nanoseconds
Input resistance10 to the twelfth ohm typical
Electrostatic rating2000 V human body model

Points to check before this part goes on a BOM

The two response numbers are not interchangeable. 200 nanoseconds is measured with 10 mV of overdrive and 100 nanoseconds with 100 mV, so a detector that sees a 2 mV crossing is outside both and will be several times slower. The offset limit of 5 mV is the reason: a unit at that limit has no overdrive at all on a 5 mV signal.

The 0.6 nanoamp maximum bias current is a factor of 120 above the 5 picoamp typical figure, and both are at room temperature. A 1 megohm source sees 5 microvolts typical and 600 microvolts worst case, which is the difference between a detector that works and one that drifts into its own offset.

Supply current at 2.7 V is lower than at 5 V, 65 microamps against 150 typical, so a battery product running the comparator directly from two cells gets both a lower supply and a lower current. The output sink at 2.7 V is also weaker, so the pull-up resistor has to be scaled with the rail.

The open drain output can be wired OR with the second channel to make a window detector with one pull-up. That arrangement is common and it works, but the leakage of the off channel, 0.1 nanoamps typical, adds to the low state of the on channel through the shared node, which matters only above about 1 megohm of pull-up.

The 2000 V human body model rating is a handling figure and not a system immunity figure. A comparator input that reaches a connector needs a series resistor and clamp diodes regardless of the ESD rating, because the rating covers assembly and not a cable discharge into the pin.

Tube packing on this order code is what the addendum now lists as obsolete. The reel code on the same die is active, so a BOM still calling the tube part for a new build is one suffix away from an available part.

Open drain means the high level belongs to the pull-up and the leakage. With 0.1 nanoamps of off state leakage at 5 V, a 1 megohm pull-up holds within 0.1 mV of the rail, so the off state is defined even for a high impedance logic input. That is the reason this output type tolerates a slow bus as well as a fast one.

Where this order code fits

Boards already released with tube packed parts: lamp and relay drivers where the comparator output drives a transistor, zero crossing detectors on a mains transformer secondary, and level shifting between a 3 V sensor and a 5 V logic rail. The LM393 pinout means an existing bipolar socket can be reused without a board change, which is why this family survives in repair and legacy builds. Boards comparing it with a neighbouring part start from our Obsolete Part Cross Reference Hub page, and boards replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can it replace an LM393 without a board change? Yes, the pinout is the same and the open drain output behaves the same way. The sink current is lower than the bipolar part at 16 mA maximum, so a load drawn near the LM393 limit has to be checked against the new figure.

Why is the tube code obsolete? TI has moved this body onto reels only. The same die in the same 8 pin SOIC is active as TLC352CDR with a 2500 piece reel.

What is the fastest response available? 100 nanoseconds with 100 mV of overdrive, and 200 nanoseconds with 10 mV. A small signal crossing is limited by the overdrive, not by the part.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.