Contact Us

TL494CDR

Brand: Texas Instruments
Texas Instruments TL494CDR is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TL494CDR — Power Management & Signal Chain | Superb Automation

TL494CDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TL494CDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TL494CDR: pulse width modulation controller with two 200 mA output transistors in a 16 pin SOIC

TL494CDR is a fixed frequency PWM controller that carries both the oscillator, the error amplifiers, the dead time control and two 200 milliamp output stages on one die in a SOIC body of 16 pins. The part runs from 7 V to 40 V, has an internal 5 V reference that holds 4.75 to 5.25 V at 1 milliamp, and two output transistors rated at 200 milliamps each, which can be wired as two single ended drivers or as one push pull pair. The oscillator is set by one resistor and one capacitor, 12 kilohms and 0.01 microfarads give 10 kHz, and the dead time control pin sets the maximum duty cycle, with 45 percent per output at zero volts on that pin.

Order code and package

Order codeTL494CDR
Functionpulse width modulation controller
PackageSOIC, 16 pins, body code D
Supply range7 V to 40 V
Reference5 V, 4.75 to 5.25 V at 1 mA
Output current200 mA per output transistor
Maximum duty cycle45 percent per output at zero dead time voltage
Oscillator10 kHz with 12 kilohms and 0.01 microfarads
Dead time threshold2.5 to 3.3 V for zero duty cycle
Standby current1.62 mA typical, 10 mA maximum
Rise and fall time85 to 200 nanoseconds rise, 20 to 100 nanoseconds fall
Temperature range0 to 70 C, C grade

Electrical parameters that decide the application

Reference regulation2 mV typical, 25 mV maximum over 7 to 40 V
Reference load regulation6 mV typical, 15 mV maximum from 1 to 10 mA
Reference short circuit35 mA
Saturation voltage0.5 V typical, 1.3 V maximum at 200 mA
Emitter follower drop1.65 to 2.5 V at minus 200 mA
Output off-state current4 to 100 microamps at 40 V
Feedback threshold at zero duty3.4 to 4.5 V
Feedback input sink current0.3 to 0.7 mA
Oscillator voltage coefficient1 Hz per kHz over 7 to 40 V
Oscillator temperature coefficient50 Hz per kHz over the range
Error amplifiertwo, with a common mode range from minus 0.3 V to VCC minus 2 V
Dead time input biasminus 0.006 to minus 10 microamps

Points to check before this part goes on a BOM

The 45 percent maximum duty cycle per output is a property of the internal toggle flip flop, not of the oscillator. In single ended mode the two outputs can be paralleled to reach about 90 percent, and in push pull mode each output is limited to 45 percent so that the two never overlap. A board that needs 48 percent per output cannot use the push pull configuration.

Output saturation of 1.3 V maximum at 200 milliamps is the number that decides whether this part can drive a MOSFET directly. At 200 milliamps and 1.3 V the transistor dissipates 260 milliwatts, which inside a 16 pin SOIC is already a thermal question, so the usual arrangement is a driver stage between the controller and the gate.

The reference is a 5 V shunt regulator with a 35 milliamp short circuit current and 25 mV of line regulation. It is normally loaded by the timing network and the divider, and anything above a few milliamps has to be checked against the 15 mV of load regulation, because the reference also sets the output voltage through the feedback divider.

Dead time is set by a voltage, not by a resistor, and the threshold for zero duty cycle is 2.5 to 3.3 V. That 800 mV window means a divider that parks the pin at 2.9 V is inside the transition region and the duty cycle will vary part to part. The pin should be driven to ground for maximum duty or above 3.3 V for zero duty, not left in between.

The oscillator runs at 10 kHz with the data sheet values and has a 50 Hz per kHz temperature coefficient, which is 5 percent over a 100 degree swing. A converter that relies on the switching frequency for EMI compliance has to either accept that drift or use an external clock, and this part has no synchronisation input.

Standby current of 1.62 milliamps typical and 10 milliamps maximum at 15 V is significant for a controller. The 10 milliamp column is what a battery product has to budget, and it is six times the typical figure, so the standby drain of a converter built around this part is not as small as the typical number suggests.

Where this order code fits

Offline and dc to dc converters, inverters, battery chargers and motor drives use this controller because it needs no external gate driver for loads below about 200 milliamps. It is also the chip most often found in older boards that are still in production, which makes the second source and the availability question important. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

Can the two outputs be paralleled for more current? They can be paralleled in single ended mode, which also gives up to about 90 percent duty cycle, but the current rating stays at 200 milliamps total because both transistors share the same die and the same thermal path.

Does this part have a soft start? Not internally. The dead time control pin can be driven by an RC network to ramp the duty cycle up at startup, which is the usual way to get a soft start with this controller.

What replaces the TL494 if it is unavailable? The TL594 is the same controller with a tighter reference and an undervoltage lockout, and the TL598 adds a totem pole output. The pinout is the same family, so a substitution is a specification check rather than a board change.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Obsolete Part Cross Reference Hub page sets out the checks that keep a substitute from failing on the bench.