Contact Us

TL431ACDBZT

Brand: Texas Instruments
Texas Instruments TL431ACDBZT is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TL431ACDBZT — Power Management & Signal Chain | Superb Automation

TL431ACDBZT

Texas Instruments — Power Management & Signal Chain

Product Overview

The TL431ACDBZT from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TL431ACDBZT: adjustable shunt reference with one percent initial accuracy in a three pin SOT-23 body

TL431ACDBZT is a programmable shunt regulator that holds 2.495 V at its reference pin and can set any output from 2.5 V to 36 V with two resistors in a SOT-23 body of 3 pins. The A grade and the DBZ package together are the tight version in the smallest body: the reference window is 2.470 to 2.520 V at 10 milliamps, which is plus or minus one percent, and the deviation over the full temperature range for SOT-23-3 devices is 6 mV typical and 16 mV maximum. The cathode can sit anywhere from 2.5 V to 36 V, the minimum operating current is 0.4 mA typical and 0.6 mA maximum, and the dynamic impedance is 0.2 to 0.5 ohms at 1 kHz.

Order code and package

Order codeTL431ACDBZT
Functionadjustable shunt regulator and reference
PackageSOT-23, 3 pins, body code DBZ
Reference voltage2.470 to 2.520 V at 10 mA, 2.495 V typical
Cathode range2.5 V to 36 V
Operating current0.4 mA typical, 0.6 mA maximum to regulate
Dynamic impedance0.2 to 0.5 ohms at 1 kHz
Reference input current2 to 4 microamps
Temperature rangeminus 40 to plus 125 C
Ratio of cathode changeminus 1.4 to minus 2.7 mV per V from 10 V to 2.5 V
Off-state leakage0.1 to 1 microamp at 36 V
Initial accuracyplus or minus one percent, A grade
DatasheetSLVS543S, revision of May 2024

Electrical parameters that decide the application

Deviation over temperature6 mV typical, 16 mV maximum for SOT-23-3
Cathode current range1 mA to 100 mA for the impedance specification
Reference drift with cathodeminus 1 to minus 2 mV per V from 36 V to 10 V
Minimum cathode voltage2.5 V at the reference point
Reference input current drift0.8 microamps typical over temperature
Noiseset by the shunt impedance and the external network
Output settlinglimited by the cathode load capacitor
ThermalSOT-23-3 lead frame, dissipation set by cathode current and voltage
Logic useworks as a comparator with the reference pin as input
Package pinoutreference, cathode and anode in SOT-23
Grade markingA grade marked on the body
Datasheet noteSOT-23-3 has a wider deviation window than the SOIC

Points to check before this part goes on a BOM

The SOT-23-3 body has a wider temperature deviation window than the larger packages: 16 mV maximum against 25 mV for other devices in the standard grade, and 6 mV typical against 4 mV. The smaller package is closer to the die and further from a stable thermal environment, and the specification reflects that rather than hiding it.

Minimum operating current of 0.6 mA maximum is the operating constraint people miss. A divider that draws 100 microamps through the cathode leaves the part out of regulation, and the output then sits somewhere between zero and the setpoint with no warning. A shunt reference always needs a bias current above the guaranteed minimum at the worst case load.

Reference input current of 4 microamps maximum flows out of the reference pin and through the top resistor of the divider, so it adds to the divider current and shifts the output. With a 10 kilohm top resistor that is 40 mV of error, which is larger than the one percent initial accuracy the A grade was bought for.

The cathode voltage coefficient of minus 1.4 to minus 2.7 mV per volt means the reference moves as the output moves. Setting a 3.3 V output from a 2.5 V reference puts 0.8 V across that coefficient, about 2 mV, while setting 30 V puts 27.5 V across it and moves the reference by up to 55 mV before the separate 36 V to 10 V term is counted.

Dynamic impedance of 0.5 ohms at 1 kHz is not the impedance at 100 kHz. The part is a shunt regulator with an internal amplifier, and above a few tens of kilohertz the impedance rises. A switching supply that uses this part in the feedback loop has to check the loop stability at the crossover frequency, not at 1 kHz.

Off-state leakage of 1 microamp maximum at 36 V is what allows the part to be used as a comparator or a crowbar. Below the reference threshold the cathode current is under a microamp, so the shunt is effectively open, and the transition happens over a few tens of millivolts of reference pin movement.

Where this order code fits

Switch mode power supplies use this part as the voltage reference on the optocoupler side of an isolated feedback loop, and linear regulators use it as a programmable shunt. It also appears as a 2.5 V reference for converters, as a comparator with a built in threshold, and as the error amplifier in a constant current sink for LED strings. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

What is the difference between the TL431A and the standard TL431? Initial accuracy. The A grade is plus or minus one percent, 2.470 to 2.520 V, and the standard part is plus or minus two percent, 2.440 to 2.550 V. The temperature deviation windows also differ by grade and package.

Can this regulate a 3.3 V rail from a 5 V supply? Yes, with a divider from the 3.3 V output to the reference pin and a cathode resistor from 5 V. The cathode resistor has to pass at least 0.6 mA plus the load current at the lowest input voltage.

Is the SOT-23 version as accurate as the SOIC? Its initial accuracy is the same one percent, but its deviation over temperature is wider: 16 mV maximum against 25 mV for the standard grade in larger bodies and 6 mV typical against 4 mV, because the small body tracks the board temperature more closely.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Obsolete Part Cross Reference Hub page sets out the checks that keep a substitute from failing on the bench.