Contact Us

TL3016ID

Brand: Texas Instruments
Texas Instruments TL3016ID is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TL3016ID — Power Management & Signal Chain | Superb Automation

TL3016ID

Texas Instruments — Power Management & Signal Chain

Product Overview

The TL3016ID from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TL3016ID: high speed comparator with complementary outputs and a latch enable in an 8 pin SOIC

TL3016ID is a comparator with 7.8 nanoseconds of propagation delay, 0.5 nanoseconds of pulse skew and a differential input stage that works from minus 3.75 V to plus 3.5 V on plus or minus 5 V rails in a SOIC body of 8 pins. The I suffix is the minus 40 to plus 85 C grade and the D suffix is the 8 pin SOIC. Propagation delay is 7.8 nanoseconds typical and 10 nanoseconds maximum with 100 millivolts of input step and 5 millivolts of overdrive, rising to 12.2 nanoseconds over the industrial range, pulse skew is 0.5 nanoseconds, the latch enable needs 2.5 nanoseconds of setup time, and the input offset is 0.5 mV typical and 3 mV maximum.

Order code and package

Order codeTL3016ID
Functionhigh speed comparator with latch and complementary outputs
PackageSOIC, 8 pins, body code D
Propagation delay7.8 nanoseconds typical, 10 maximum at 5 mV overdrive
Pulse skew0.5 nanoseconds between rising and falling edges
Latch setup time2.5 nanoseconds
Supplyplus or minus 5 V, also specified at 5 V single supply
Input offset0.5 mV typical, 3 mV maximum
Input bias current6 microamps typical, 10 maximum
Supply current10.6 mA typical, 12.5 mA maximum from the positive rail
Temperature rangeminus 40 to plus 85 C, I suffix
DatasheetSLCS130D, revision of March 2000

Electrical parameters that decide the application

Offset driftminus 4.5 microvolts per degree
Input offset current0.1 microamp typical, 0.6 maximum
Input common modeminus 3.75 V to plus 3.5 V on plus or minus 5 V
Common-mode rejection80 dB minimum, 97 dB typical
Negative supply rejection80 dB minimum, 100 dB typical
Output low500 mV at 4 mA sink, 750 mV at 10 mA
Output high3.6 V at 1 mA source, 3.4 V at 10 mA
Negative supply currentminus 1.3 to minus 2.4 mA
Logic thresholds0.8 V low, 2 V high on the latch enable
Latch input current24 to 45 microamps
Output drive10 mA source and sink
Overdrive conditionspecified at 5 mV and at 20 mV

Points to check before this part goes on a BOM

The propagation delay depends on the overdrive, and the difference is not cosmetic. At 100 millivolts of step with 20 mV of overdrive the delay is 7.6 nanoseconds, and with 5 mV it is 7.8, but the maximum column widens from 11.2 to 12.2 nanoseconds over temperature at the smaller overdrive. A comparator used on a slow moving signal sees only microvolts of overdrive at the crossing and takes far longer than 8 nanoseconds.

The input common mode range is minus 3.75 V to plus 3.5 V on plus or minus 5 V rails, which is not rail to rail and is asymmetric. A signal that swings to the positive rail is outside the window, and the comparator's response there is undefined rather than merely slow. Series resistors or a level shift are needed for rail referenced signals.

Input bias current of 10 microamps maximum is large for a comparator with 0.5 mV of offset. Through a 1 kilohm source it is 10 millivolts, twenty times the offset, so a low impedance source is mandatory and a high impedance one needs a buffer. This is the price of a 7 nanosecond part with a bipolar input.

Pulse skew of 0.5 nanoseconds against a 7.8 nanosecond delay is a 6 percent asymmetry, which matters in a time to digital converter where the difference between the rising and falling edges is the measurement. The skew is specified at 25 C and is not guaranteed over temperature, so a board that depends on it has to calibrate.

The latch enable has 2.5 nanoseconds of setup time and the input draws 24 to 45 microamps, which is enough that a 10 kilohm series resistor would drop 0.45 V and slow the edge. Latch lines should be driven from a low impedance source with a short trace, and the 45 microamp maximum is what the driver has to supply at the logic threshold.

The negative supply current is only 1.3 to 2.4 milliamps against 12.5 milliamps on the positive rail, so the part is not symmetric and a single supply 5 V board loses the negative rail entirely. In that configuration the input range becomes 1.25 V to 3.5 V, which is a narrow window for a signal that swings to ground.

Where this order code fits

Zero crossing detectors in switching supplies, pulse width discriminators, timing recovery circuits and fast level detectors use this part. Its complementary outputs and latch enable make it usable as a fast set reset element or as a sampler in a time to digital converter front end. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Obsolete Part Cross Reference Hub page.

Questions buyers ask

Can this comparator work from a single 5 V supply? Yes, and the input common mode then runs from 1.25 V to 3.5 V. Signals below 1.25 V, including ground, are outside the specified window, so a ground referenced zero crossing detector needs a level shift.

What is the latch enable for? It holds the output state regardless of the input, which lets a fast comparator sample a signal at a known instant. Setup time is 2.5 nanoseconds, so the enable has to arrive before that window closes.

How much overdrive does the 7.8 nanosecond figure assume? 5 to 20 millivolts above the threshold. At smaller overdrive the delay grows, which is why a slow moving input near the crossing is much slower than the headline number.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.