Contact Us

SN65LVDS179DGKR

Brand: Texas Instruments
Texas Instruments SN65LVDS179DGKR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65LVDS179DGKR — Power Management & Signal Chain | Superb Automation

SN65LVDS179DGKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65LVDS179DGKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65LVDS179DGKR: single LVDS driver and receiver pair in the eight pin VSSOP at up to 150 Mbps full duplex

SN65LVDS179DGKR is a low voltage differential signalling transceiver that pairs one driver with one receiver for a full duplex link in a VSSOP body of 8 pins. It meets the ANSI TIA/EIA-644-1995 electrical standard, drives a 247 mV minimum differential into a 100 ohm load from a single 3.3 V supply, and receives a 100 mV differential with up to 1 V of ground difference between the two ends. The driver propagates in 1.7 ns and the receiver in 3.7 ns, and the pair dissipates 25 mW in the driver and 60 mW in the receiver at 200 MHz.

Order code and package

SN65LVDS179DGKRVSSOP DGK body, 8 pins, 2500 pieces on a large reel, Active in the addendum dated 5 June 2026, NIPDAU finish, moisture level 1 with no floor life limit, marking S79, minus 40 to plus 85 degrees
SN65LVDS179DGKthe same DGK body in an 80 piece tube at the same moisture level, which is the prototype quantity and the tube marking reads DL179 rather than S79
SN65LVDS179DRSOIC D body, 8 pins, 2500 pieces on a large reel at moisture level 2 with a one year floor life, marking S79, for a board that already has a leaded footprint
SN65LVDS179Dthe same SOIC body in a 75 piece tube, moisture level 1, marking DL179
SN65LVDS180Dthe two driver and two receiver member of the same family in the fourteen pin SOIC, which is the part to compare when the link needs a second channel in the other direction

Electrical parameters that decide the application

StandardANSI TIA/EIA-644-1995, the LVDS electrical standard, which fixes the 247 mV minimum differential and the 100 ohm load
Signalling rateup to 150 Mbps full duplex on this member, and up to 400 Mbps on the family members that use both directions in one pair arrangement
Supplysingle 3.3 V rail with 5 V tolerant LVTTL inputs, so a 5 V controller drives it without a level shifter
Differential output350 mV typical into a 100 ohm load with a 247 mV minimum magnitude, and a common mode that stays inside the receiver window
Receiver threshold100 mV of differential with up to 1 V of ground potential difference between the driver and the receiver grounds
Propagation delay1.7 ns typical in the driver and 3.7 ns typical in the receiver, which is what allows a 150 Mbps link over a short backplane
Power25 mW typical in the driver and 60 mW typical in the receiver at 200 MHz, far below the equivalent emitter coupled logic stage
Bus pin protectionexceeds 12 kV of human body model ESD on the bus pins, which is a board handling figure rather than a surge rating
Fail safethe receiver keeps a high input impedance with the supply below 1.5 V and has an open circuit fail safe that holds the output in a defined state on an unplugged cable
Output levelsLVTTL compatible on both the driver input and the receiver output, so the part connects to a 3.3 V logic device without external components
Temperatureminus 40 to plus 85 degrees, which is the industrial range and not the 125 degree automotive one

Family variants and how they differ

SN65LVDS179 against SN65LVDS180the 180 carries two drivers and two receivers in a fourteen pin body and reaches 400 Mbps in one arrangement, while this part carries one of each in eight pins, so the channel count and the pin budget decide between them
SN65LVDS050 and SN65LVDS051sixteen pin members of the same family with two drivers and two receivers and a different pin arrangement, used where a wider body is acceptable
Against a CML or LVPECL driverLVDS runs at a lower swing and a lower power, and the receiver tolerance of 1 V of ground difference is what makes it work across a backplane connector where the two cards have separate grounds
Against an RS-485 transceiverRS-485 reaches hundreds of metres and multi-drop, LVDS reaches tens of metres point to point, so the choice is made by the distance and the topology rather than by the data rate
Body optionsthe DGK and D bodies are the same silicon, and the moisture level differs between them, level 1 on the VSSOP reel and level 2 on the SOIC reel

Points to check before this part goes on a BOM

The 150 Mbps figure is for full duplex on this member and the family reaches 400 Mbps only in the arrangements that use both pairs in the same direction. A link specified at 300 Mbps cannot be built on the 179, and the datasheet table that lists the rates per device is the one to read rather than the family headline.

The 247 mV minimum differential into 100 ohm is the standard figure and the 350 mV typical is what the part produces. The gap matters at the end of a long cable, where the attenuation eats the margin: a cable that loses 6 dB reduces the 350 mV to 175 mV, which is below the standard minimum but still above the 100 mV receiver threshold, so the link works while being outside the standard. That is why the vendor publishes both numbers.

The 1 V of ground potential difference is the specification that decides whether this part can cross a backplane connector. Two cards on the same chassis can sit a few hundred millivolts apart under load, and a receiver with a 1 V window handles that. Beyond 1 V the common mode moves the differential pair outside the input range and the link fails, which is the point where an isolated transceiver becomes necessary.

The fail safe on an open circuit is a defined output state rather than a floating one, and that is what keeps a system from acting on noise when a cable is unplugged. The receiver maintains a high input impedance below 1.5 V of supply, so a powered down card does not load the bus. Both behaviours are the reason LVDS is used in hot swap equipment rather than only for its speed.

The 12 kV of bus pin ESD is a handling and assembly figure and not a cable surge rating. A connector on the outside of an enclosure sees the human body model through a cable, which is a different path with more inductance, and that needs a transient suppressor. Reading the 12 kV as a surge rating is a common mistake in equipment that then fails in the field on a dry day.

The temperature ceiling of 85 degrees is the practical difference from the automotive versions of the same function. A telecom line card in a cabinet at 55 degrees is fine; an engine bay or a base station cabinet at 75 degrees ambient is not. The part is a 3.3 V industrial transceiver and the automotive family is a separate set of strings.

Pair routing and what the receiver tolerates

The differential pair has to stay matched within a few millimetres over its length, because the receiver threshold of 100 mV is small enough that a skew of a few hundred picoseconds turns a clean eye into a marginal one at 150 Mbps. The termination resistor is 100 ohm across the pair at the receiver end only, and a second termination at the driver end halves the swing and is a common error on a multi-drop attempt.

The common mode of the driver output is fixed internally rather than driven from a reference pin, so a pair that runs past a switching supply picks up common mode noise that the receiver must reject. The 1 V of ground difference tolerance is not the same as 1 V of noise at 100 MHz, and a pair that runs beside a switching node needs the usual spacing and ground return rather than reliance on the receiver.

Where 8 pins are enough

A full duplex link on two pairs needs one driver and one receiver at each end, which is exactly what the 179 provides in eight pins. The 180 exists for the case where an additional channel is needed and the board has fourteen pins of room. Choosing the 180 for a single channel wastes board area and adds a second pair that must be terminated, so the smaller part is usually the correct one.

Where this order code fits

Wireless infrastructure, telecom line cards, printers and backplane links are the applications the vendor names, and each of them runs a short differential link between two cards that do not share a ground. Teams comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

What data rate does this member reach? 150 Mbps full duplex. The 400 Mbps figure belongs to other members of the family, not to the 179.

Does it work with a 5 V controller? Yes. The LVTTL inputs are 5 V tolerant, so a 5 V logic device drives it without a level shifter.

What happens when the cable is unplugged? The receiver open circuit fail safe holds the output in a defined state rather than letting it float.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Obsolete Part Cross Reference Hub page sets out the checks that keep a substitute from failing on the bench.