SN65LBC179ADR
Product Specifications
SN65LBC179ADR
Texas Instruments — Power Management & Signal Chain
Product Overview
The SN65LBC179ADR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
SN65LBC179ADR: 5 V line driver and receiver pair for a 30 Mbps four wire link
SN65LBC179ADR is a differential driver and a differential receiver in one eight pin body on a single 5 V rail, wired to separate pins so one pair of wires carries traffic in each direction at the same time in a SOIC body of 8 pins. It reaches 30 Mbps by the TIA/EIA-485-A definition, protects the bus pins beyond 12 kV human body model, draws 8.5 mA typical and 15 mA maximum while enabled and 700 uA maximum while disabled, and holds a common mode window of minus 7 V to plus 12 V. The driver delivers 1.5 V typical into 54 ohm with a steady state common mode between 1.8 V and 2.8 V, limits a short circuit to 250 mA and shuts down on over temperature. Propagation is 6 ns typical and 12 ns maximum, and the receiver switches on plus or minus 200 mV with 50 mV of hysteresis.
Order code and package
| SN65LBC179ADR | SOIC D body, 8 pins, 4.90 mm by 3.91 mm, Active, 2500 pieces on a large reel, minus 40 to plus 85 degrees, marking BL179A. The plain row prints the finish and the moisture level as Call TI rather than a value |
| SN65LBC179ADR.A | the same reel with NIPDAU finish and moisture level 1 with unlimited floor life, which is the row a material declaration should name |
| SN65LBC179ADRG4 | the lead free declaration of the same reel, also NIPDAU and level 1, with the same marking |
| SN65LBC179AD | the tube row of the same body, printed Obsolete with no quantity and no carrier, so the string without an R is the one to avoid on a new order |
| SN65LBC179AP | the PDIP body at 50 pieces in a tube, but the package row prints 0 to 70 degrees, which is the commercial window rather than the industrial one the 65 grade normally carries |
| SN75LBC179A | the commercial sibling, 0 to 70 degrees. The AD tube row is still in production, the DR and P rows are printed Obsolete |
Electrical parameters that decide the application
| Supply | 4.75 V to 5.25 V on a single rail, which is the standard 5 V tolerance. There is no 3.3 V option in this family, so a 3.3 V board needs the HVD family instead |
| Signalling rate | 30 Mbps by the TIA/EIA-485-A definition, with the standard restricting transition times to 30 per cent of the bit length. The vendor notes that higher rates are reachable outside that restriction, which is a bench observation and not a guaranteed figure |
| Duplex | the driver outputs Y and Z and the receiver inputs A and B are separate pins, so the part is a full duplex pair on four wires. Two of these back to back make a bidirectional link without any direction switching |
| Driver output | 1.5 V typical into the 54 ohm RS-485 load, with 1.1 V printed as the minimum on the commercial grade rows. A heavily loaded bus or a long cable erodes that margin first |
| Common mode output | 1.8 V minimum, 2.4 V typical and 2.8 V maximum steady state, with a 0.1 V limit on the change between high and low. That window is what keeps the far end receiver inside its input range |
| Short circuit | plus or minus 250 mA of output current limit with thermal shutdown, so a miswire to a supply rail heats the part and then parks it instead of destroying it |
| ESD | more than 12 kV human body model on the bus pins, tested to MIL-STD-883C method 3015.7 rather than a board level standard, so the number is a pin rating |
| Supply current | 8.5 mA typical and 15 mA maximum enabled, 700 uA maximum disabled. The disabled figure is what makes the part usable on a bus where several cards are powered down |
| Receiver | plus or minus 200 mV of differential threshold with 50 mV of hysteresis, a 4.9 V typical high output and 0.8 V maximum low output at 8 mA, which drives a 5 V CMOS input directly |
| Switching | driver propagation 6 ns typical and 12 ns maximum, rise and fall 7.5 ns typical, receiver propagation in the same range, and a pulse skew small enough that a 30 Mbps eye stays open |
| Power off | the bus pins present plus or minus 10 uA of leakage with the rail at zero, so an unpowered card does not drag a live bus down |
| Temperature | minus 40 to plus 85 degrees on the 65 grade and 0 to 70 on the 75 grade, which is a narrow window compared with the 125 degree isolated parts used in the same cabinets |
Family variants and how they differ
| 179A against 176A | the 176 is a transceiver with the driver and receiver sharing the same pair, so it is half duplex. The 179A is a pair with separate pins and gives full duplex on four wires |
| Against SN65HVD179 | the HVD179 adds balanced receiver thresholds for fieldbus fail safe and keeps the same eight pin outline, but it needs 3 state control and is a different document. The LBC179A is always enabled and cannot be parked |
| Against the 3.3 V family | an SN65HVD1473 runs at 20 Mbps on 3.3 V with enables and 256 nodes. The LBC179A is faster on paper, runs on 5 V only, and has no enable pins, so the choice is made by the rail and by the bus topology |
| Against an isolated part | an ISO1450 class device puts a barrier inside the package and needs an isolated supply. A link inside one cabinet does not need it, a link between cabinets often does |
| Against a 75179 style part | the older parts in this outline are slower and carry no IEC contact discharge rating. The A version was introduced for switching performance, and the plain 179 strings are not printed in this addendum |
Points to check before this part goes on a BOM
The finish column is the first thing to settle on this string. SN65LBC179ADR prints Call TI for both the lead finish and the moisture level, while the .A and the G4 rows of the same reel print NIPDAU and level 1 with unlimited floor life. A customer who has to file a material declaration, or an assembly house that has to write a floor life onto a process card, needs the .A or the G4 string, and that is a purchasing decision rather than an engineering one.
There are no enable pins on this part, so the driver is always driving and the receiver is always listening. That is fine for a link where one end owns the transmit pair, which is the four wire case the part was built for. It is not fine for a two wire multidrop bus where every node has to release the pair between frames, and a customer who tries that will see two drivers fighting on the same wires.
The PDIP rows print 0 to 70 degrees even though the device is the 65 grade. A through hole part in a cabinet that reaches 60 degrees internally is therefore at the top of its window with no margin, and the industrial range on the SOIC rows does not carry across to the wider package.
The 30 Mbps figure is a rate the cable has to support. At that rate the transition time budget is a fraction of the bit, and a long or poorly terminated cable will close the eye before the driver runs out of speed. The practical ceiling for a 100 m run is far below 30 Mbps, and quoting the datasheet figure against a long field cable is a common way to produce a link that works on the bench and fails on site.
The short circuit limit of 250 mA and the thermal shutdown are survival features, not operating points. A driver held into a fault will heat the eight pin body quickly, and the shutdown will release when it cools, which a customer experiences as a port that recovers by itself after a wiring fault. That behaviour is normal for this part and should be written into the fault procedure rather than treated as a failure.
Nothing in this part isolates anything. The common mode window of minus 7 V to plus 12 V is the range the receiver tolerates, and it assumes a shared ground reference. Two cabinets on different earths will exceed that window long before the transceiver fails, and the symptom is corrupted frames rather than a dead part.
Why a pair and not a transceiver
Four wire links appear wherever the two directions never share a pair: motor encoder feedback, SSI and absolute encoder interfaces, and point to point links between a controller and a remote rack. A pair like this one removes the direction switching from the firmware, which removes a whole class of timing bugs.
The cost is two extra wires and a receiver that is always listening. On a short link inside one enclosure that is a good trade, because the cable is cheap and the firmware is simpler. On a field bus with dozens of nodes it is the wrong part, because every node would drive the same pair.
What the order code decides
The string reads SN65LBC179A for the device, D for the SOIC body and R for the large reel of 2500. The P in the same position is the PDIP body, which is a different footprint and, per the addendum, a different temperature column. The 65 or 75 in the prefix sets the temperature grade, and nothing in the suffix changes it.
The G4 suffix is the lead free declaration of the same reel and does not change the silicon. The A suffix on the row, as in DR.A, is the vendor's re-release of the same reel with the finish and the moisture level written down, which is why the two rows of the same part print different paperwork.
Where this order code fits
Motor and encoder links, remote rack connections and any point to point link where the two directions have their own pair. It is also used as a receive only tap on a multidrop bus, where the always enabled driver is harmless because the node never transmits. Teams comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and teams replacing a part that has gone end of life start from the Obsolete Part Cross Reference Hub page.
Questions buyers ask
Is SN65LBC179ADR still orderable? Yes, the R row is Active at 2500 pieces on a large reel. The plain SN65LBC179AD tube row is printed Obsolete, and the commercial SN75LBC179ADR and P rows are obsolete as well.
Which row carries a documented finish? SN65LBC179ADR.A and SN65LBC179ADRG4 print NIPDAU with moisture level 1 and unlimited floor life. The plain DR row prints Call TI in both columns.
Can several of these share one pair? No. The driver has no enable pin and is always on, so only one node may drive a given pair. Use a transceiver with a driver enable for a two wire multidrop bus.
What happens with the rail removed? The bus pins leak plus or minus 10 uA at zero rail voltage, so an unpowered card sits on the bus without loading it and can be inserted into a live link.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.