Contact Us

SN65HVD233HD

Brand: Texas Instruments
Texas Instruments SN65HVD233HD is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65HVD233HD — Power Management & Signal Chain | Superb Automation

SN65HVD233HD

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65HVD233HD from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65HVD233HD: 3.3 V CAN transceiver with loopback and 36 V bus fault protection

SN65HVD233HD is a 3.3 V controller area network physical layer transceiver in a SOIC body of 8 pins. It connects a CAN controller to a differential two wire bus at rates up to 1 Mbit/s and carries fault protection on the bus pins beyond plus or minus 36 V. The H suffix marks the SOIC-8 body in the D package, and the loopback pin is what separates this member from the sleep and autobaud versions of the same family.

Order code and package

Order codeSN65HVD233HD
Package8-pin SOIC, D body, 4.90 mm by 3.91 mm
Packingtube or tape and reel depending on the order
Bus pinsCANH and CANL, half duplex differential
Logic sideTXD, RXD, and the RS, EN and LBK control pins
ProtocolISO 11898-2 physical layer, 1 Mbit/s maximum
Mode controlloopback through the LBK pin on this member of the family

Electrical parameters that decide the application

Supply3 V to 3.6 V, 3.3 V nominal
Bus fault protectionbeyond plus or minus 36 V on CANH and CANL
ESD on the bus pinsplus or minus 16 kV HBM, 3 kV on all pins
Common mode rangeminus 7 V to plus 12 V
Dominant differential output1.5 V to 3 V into a 60 ohm load
Recessive differential outputplus or minus 120 mV
Node counthigh input impedance allows 120 nodes on one bus
Thermal shutdownjunction temperature near 170 degrees Celsius

Family variants and how they differ

SN65HVD233loopback mode through the LBK pin, the part on this page
SN65HVD234sleep mode at about 50 nA typical instead of loopback
SN65HVD235autobaud loopback, for rate detection at start up
SN65HVD230 familyearlier members without the mode pin arrangement

Points to check before this part goes on a BOM

The transceiver is a physical layer part and holds no protocol state. Frame formatting, arbitration, error counters and the bus off rule all sit in the controller, so the choice of transceiver changes the analogue behaviour of the bus and nothing about how the network behaves logically.

The 36 V fault rating is what lets a 3.3 V node sit on a bus that is also wired to 24 V industrial equipment. A short from CANH to a 24 V rail is a normal field fault in a cabinet, and the part survives it because the bus pins are rated well past that voltage; the controller behind it is not, so the series resistance between the two still matters.

Loopback through LBK routes the transmit data back to the receiver output while the driver stays on the bus. That is a self test of the digital path and of the pin connections, and it does not test the cable or the termination. A board that passes loopback can still fail on a bus, which is why the test is a start up check rather than a production proof.

The dominant differential output of 1.5 V to 3 V into 60 ohm is what the receiver threshold window expects. With two 120 ohm terminators in parallel the bus is 60 ohm, so the load in the table is the real case rather than a bench convenience, and a bus with one terminator presents 120 ohm and a slightly higher swing with more ringing.

Common mode range of minus 7 V to plus 12 V is wider than the 3.3 V rail, and that is deliberate: ground potential differences between cabinets move the whole bus, and a transceiver that only accepted rail referenced signals would fail as soon as two cabinets sat on different earths. The limit is a signal quality limit, not a survival limit.

Thermal shutdown at about 170 degrees protects the driver when CANH is shorted to a supply or to ground for a long time. The driver turns off and the receiver keeps working, so a controller that keeps transmitting into a short sees no acknowledge and eventually goes bus off. That sequence is the intended behaviour and not a fault in the part.

Power dissipation is modest but not zero: the data sheet gives 36.4 mW average at 3.3 V with a 1 MHz square wave into 60 ohm. In the 8-pin SOIC the junction to ambient figure is 101 degrees per watt on a high conductivity board, so 36 mW is under 4 degrees of rise and the package is never the thermal question in a CAN node.

The five volt tolerant logic inputs are what let this part sit behind a 5 V microcontroller. TXD, EN, LBK and RS all accept 5.5 V with a 3.3 V supply, so no level shifter is needed, and RXD swings to VCC, which a 5 V controller reads as a valid low and a marginal high. A 5 V controller should confirm its input high threshold against a 3.3 V RXD before the board is frozen.

The RS pin sets the driver transition time, and on this member of the family it is a slope control rather than a plain mode bit. A resistor to ground slows the edges and reduces emissions at the cost of loop length, while tying it low gives the fastest edges. It is the one component on the node that a product can tune after an EMC test, and it should be a real resistor rather than a zero ohm link.

Termination is two 120 ohm resistors, one at each physical end of the trunk, not one per node. A star topology with a terminator at every branch loads the bus with several resistors in parallel and asks the driver for current the 1.5 V minimum is not specified at. Long stubs off the trunk produce reflections that the 80 mV of receiver hysteresis cannot clean up.

A node that loses power must not pull the bus down. The high input impedance in low supply conditions is what keeps an unpowered transceiver from loading a live bus, and the family specification puts the leakage low enough that a dozen unpowered nodes on one trunk still leave the active driver inside its load limit.

The receiver output RXD swings to the 3.3 V rail and has a 10 mA class output, so it can drive a controller input directly and also an optocoupler through a resistor. In an isolated node the optocoupler is on the controller side, not on the bus side, and the propagation delay it adds has to be counted in the arbitration timing at 1 Mbit/s.

Where this order code fits

It is used in motor drives, building controllers, battery management units and vehicle modules where a 3.3 V controller has to reach a 5 V or 24 V industrial bus. Teams comparing it with a neighbouring part start from our CAN Bus Transceiver Selection page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can the loopback pin be left floating? No. LBK is a mode input and has to be tied to a defined level. Floating it puts the part in an undefined mode, and a node that boots into loopback reports a healthy local path while saying nothing on the bus.

Does it need a 5 V rail? It does not. The supply is 3 V to 3.6 V and the logic inputs are 5 V tolerant, so a 5 V controller can drive it directly without a translator.

What terminates the bus? Two 120 ohm resistors, one at each physical end, giving 60 ohm differential. The 1.5 V to 3 V dominant output in the table is specified into that load.

Is it the same footprint as the 5 V CAN parts? The 8-pin SOIC footprint is shared across the family, but the 5 V parts (SN65HVD230 class) have a different supply range and cannot be substituted on a 3.3 V board without checking the logic thresholds.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.