SN65HVD1473DGSR
Product Specifications
SN65HVD1473DGSR
Texas Instruments — Power Management & Signal Chain
Product Overview
The SN65HVD1473DGSR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
SN65HVD1473DGSR: 3.3 V full duplex RS-485 transceiver at 20 Mbps with enables
SN65HVD1473DGSR is a differential driver and receiver on a single 3.3 V rail, with separate bus pins for each direction and an enable pin for each block, in a ten pin VSSOP in a VSSOP body of 10 pins. It reaches 20 Mbps, loads the bus at one eighth of a unit load so 256 nodes fit, and takes more than plus or minus 30 kV human body model, more than plus or minus 16 kV IEC 61000-4-2 contact discharge and more than plus or minus 4 kV IEC 61000-4-4 fast transient burst on the bus pins. Receiver hysteresis is 70 mV, quiescent current is under 1.1 mA with a standby state at 10 nA typical and below 5 uA maximum, the logic inputs take 5 V levels, and the part is characterised from minus 40 to plus 125 degrees.
Order code and package
| SN65HVD1473DGSR | VSSOP DGS body, 10 pins, 2500 pieces on a large reel, NIPDAUAG finish, moisture level 1 with unlimited floor life, minus 40 to plus 125 degrees, marking 1473 |
| SN65HVD1473DGS | the same body at 80 pieces in a tube, which is the row a prototype order comes from |
| SN65HVD1473DR | the SOIC D body with 14 pins and a 8.65 mm by 3.91 mm outline, 2500 pieces on a large reel. The addendum prints its finish cell as NIPDAU or NIPDAUAG in the same line |
| SN65HVD1473DRG4 | the lead free declaration of the SOIC reel at 2500 pieces |
| SN65HVD1473D | the SOIC tube row at 50 pieces, printed Active, which is unusual for an interface part of this age and worth knowing when a repair order needs a handful |
Electrical parameters that decide the application
| Supply | a single 3.3 V rail, with logic inputs that tolerate 5 V so the same part sits behind a 3.3 V or a 5 V controller without a shifter |
| Signalling rate | 20 Mbps on this member, with the bit time printed as 50 ns or longer. The family splits into 400 kbps, 20 Mbps and 50 Mbps members on the same die family |
| Duplex | separate A and B receiver inputs and Y and Z driver outputs, so the part is full duplex on four wires and does not need a direction turnaround |
| Node count | one eighth of a unit load, so up to 256 nodes on one bus. That is the number that removes a repeater from a long trunk |
| Enables | an active high driver enable and an active low receiver enable, so both blocks can be parked and the part drops into a standby state below 5 uA |
| ESD | more than plus or minus 30 kV human body model, more than plus or minus 16 kV IEC 61000-4-2 contact discharge and more than plus or minus 4 kV IEC 61000-4-4 burst, all printed on the bus pins |
| Hysteresis | 70 mV of receiver hysteresis, which is what keeps a slow, attenuated edge at the far end of a long cable from counting twice |
| Quiescent current | under 1.1 mA while operating, 10 nA typical and below 5 uA maximum in standby with both blocks disabled |
| Enable timing | the driver enable is printed in nanoseconds, 20 ns maximum, while the receiver enable is printed in microseconds, 8 us maximum. That asymmetry is the reason a firmware that turns the receiver on and reads immediately loses the first bytes |
| Fail safe | the receiver holds a defined output with the bus open, shorted or idle, so an unplugged connector does not produce a false start bit |
| Power sequencing | glitch free on power up and power down, so a card inserted into a live bus does not drive the pair while its rail is still rising |
| Temperature | minus 40 to plus 125 degrees on every printed row, and a moisture level 1 with unlimited floor life on this reel |
Family variants and how they differ
| 1473 against 1474 | the same 20 Mbps member without enable pins. A backplane tap that never transmits can use the 1474 and save the two control lines, while a node that takes turns needs the 1473 |
| 1473 against 1476 | the 50 Mbps member with the same enables and the same body options. The faster part needs a shorter, better terminated bus, so moving up is a change to the cable as well as the bill of materials |
| 1473 against 1470 | the 400 kbps member, which is the one for a long meter trunk where the cable, not the silicon, sets the rate |
| Against the 5 V LBC family | the LBC179A offers 30 Mbps on 5 V with no enables, the 1473 offers 20 Mbps on 3.3 V with enables and 256 nodes. The rail and the topology decide, not the headline rate |
| Against an isolated part | an ISO1430 class device carries a 12 Mbps isolated port in one package and needs a supply on the bus side. A pair inside one cabinet does not need it |
Points to check before this part goes on a BOM
The enable times are not symmetric and the difference bites in firmware. The driver turns on within 20 ns, the receiver within 8 us, so a node that enables the receiver and reads the first byte in the same microsecond sees a stale or undefined level. The usual fix is a delay or a listen first protocol, and it belongs in the driver software rather than in a hardware change.
The two bodies are not interchangeable. The DGS is a ten pin VSSOP and the D is a fourteen pin SOIC, and the comparison table in the same document prints SOIC-8 and MSOP-8 lines in a column that belongs to the other members of the family. Any footprint decision has to be read from the ordering row, not from the pin count in the table.
The standby current of 5 uA only holds when both the driver and the receiver are disabled. A board that parks the driver but leaves the receiver enabled draws the full operating current of the receiver, which is most of the 1.1 mA quiescent figure. That distinction is easy to miss because the data sheet prints one quiescent number for the whole part.
The 256 node figure is a loading calculation, not a wiring permission. Every node adds capacitance, every terminator adds DC load, and a bus with 256 nodes needs a cable and a stub arrangement that no field installation will match. In practice the loading number matters because it allows a longer trunk, not because anyone connects 256 devices.
The moisture level differs across the family: this reel is level 1 with unlimited floor life, while the 1471 rows of the same document print level 2 with a one year floor life. A board that mixes members carries two process rules, and an assembly house that applies one rule to both will either bake parts that did not need it or skip a bake that was required.
The 30 kV human body model figure is a pin rating under a component level test. It says the die survives a discharge at the pin, not that a port built from it survives a cable strike. A customer who needs a system number has to look at the IEC contact discharge figure and at the board level protection around it.
Why 3.3 V matters on this port
Most industrial controllers moved to 3.3 V years ago, and a 5 V transceiver in front of a 3.3 V controller needs level shifting on both the data and the enable lines. This part removes those parts, removes a rail, and keeps the 5 V tolerant inputs so an older controller can still drive it.
The 20 Mbps member covers the usual fieldbus rates with room to spare, and the 50 Mbps members are there for a backplane or a short cabinet link where the cable supports it.
What the order code decides
The string reads SN65HVD1473 for the device, DGS for the ten pin VSSOP and R for the large reel of 2500. The D in that position is the fourteen pin SOIC, which is a different footprint with the same function.
The G4 suffix is the lead free declaration. Nothing in the string selects the rate, the node count or the enable behaviour, because those belong to the device number, so a purchase order that changes 1473 to 1476 by hand buys a faster driver with the same pinout and a different cable requirement.
Where this order code fits
Industrial automation, encoder and decoder links, building automation, security networks and telecom rack connections where the controller runs at 3.3 V and the bus is a four wire full duplex pair. Teams comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and teams replacing a part that has gone end of life start from the Obsolete Part Cross Reference Hub page.
Questions buyers ask
Is the ten pin body the same footprint as the fourteen pin part? No. DGS is a ten pin VSSOP and D is a fourteen pin SOIC. The function is the same and the pinout is not, so a board change is needed to move between them.
How long does the receiver take to enable? 8 microseconds maximum, against 20 nanoseconds for the driver. Firmware that reads immediately after enabling the receiver will lose the first bytes.
What current does it draw in standby? 10 nA typical and below 5 uA maximum, but only with both the driver and the receiver disabled. Leaving the receiver enabled keeps the operating current flowing.
Which protection numbers are on the bus pins? More than plus or minus 30 kV human body model, more than plus or minus 16 kV IEC 61000-4-2 contact discharge and more than plus or minus 4 kV IEC 61000-4-4 fast transient burst.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.