LM324DR
Product Specifications
LM324DR
Texas Instruments — Power Management & Signal Chain
Product Overview
The LM324DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LM324DR: the plain quad op amp on a 5000 piece reel
LM324DR is the plain grade of the quad operational amplifier in the fourteen pin small outline body, on a large tape and reel, from 0 to plus 70 degrees. Seven millivolts of offset maximum at room temperature, nine over the window, 1.2 megahertz of gain bandwidth, and four amplifiers that together draw under a milliamp.
This is the code that fills the largest number of boards in the world. It sits in sensor conditioning, comparator chains, active filters, buffers and reference dividers, and it is chosen because it works from 3 to 32 volts, accepts inputs at ground, and costs almost nothing. The engineering question is not whether it is good enough in general but whether the offset window and the speed are good enough for this board.
The grade and the carrier
LM is the family, 324 is the quad amplifier with the 0 to 70 window, D is the fourteen pin small outline body, and R is the reel. There is no A in the string, so this is the plain sort, and the addendum prints this row on a 5000 piece reel, twice the quantity of the A sort beside it.
| Orderable code | LM324DR |
| Amplifiers per body | 4, independent |
| Body | SOIC, 14 pins |
| Carrier | large tape and reel, 5000 pieces |
| Reel diameter | 330 millimetres |
| Tape width | 16.4 millimetres |
| 6.5 by 9.0 millimetres, 2.1 millimetres deep | |
| Pitch | 8 millimetres |
| Offset at 25 degrees | 3 millivolts typical, 7 maximum |
| Offset over the window | 9 millivolts maximum |
| Input bias current at 25 degrees | 20 nanoamps typical, 150 maximum |
| Common mode range | ground to 1.5 volts below the positive rail |
| Gain bandwidth product | 1.2 megahertz |
| Slew rate | 0.5 volts per microsecond |
| Supply current, four amplifiers | 0.7 milliamps typical at 5 volts |
| Temperature window | 0 to plus 70 degrees |
What nine millivolts over the window means in a real chain
A sensor with a 20 millivolt full scale output and a gain of fifty needs an input offset below 4 millivolts if the error is to stay under 1 percent of full scale at the amplifier input. The plain sort does not meet that without a trim, and the A sort at 5 millivolts over the window does not either. That is the arithmetic that pushes a precision front end to a different part, and it is worth doing before the board is built rather than after.
On a digital threshold or a comparator chain the arithmetic is kinder. If the amplifier is buffering a divider and the following stage is a comparator with its own offset, the two errors add, and 9 millivolts plus 9 millivolts is 18 millivolts against a threshold that might have 500 millivolts of margin. That works.
Bias current is the second term and it scales with source impedance. At 150 nanoamps maximum and 10 kilo ohms the error is 1.5 millivolts, which is small. At 1 megaohm it is 150 millivolts, which is larger than the signal on a current sense shunt, and that is the point where a CMOS input amplifier becomes mandatory rather than preferable.
The supply range and the output swing
The family runs from 3 to 32 volts, which covers a 5 volt logic rail, a 12 volt automotive rail and a 24 volt industrial rail with the same part number. The input range includes ground on all of them, and stops 1.5 volts below the positive rail at room temperature, 2 volts over the window.
The output does not reach either rail. On 5 volts with a 2 kilo ohm load it swings roughly 0.1 to 3.5 volts, on 30 volts with a 10 kilo ohm load it reaches 26 volts. A circuit that needs a 0.5 to 4.5 volt swing from a 5 volt rail is fine, and a circuit that needs 4.9 volts is not, and the difference is a resistor to the rail or a different amplifier.
The 0.5 volt per microsecond slew rate sets the large signal bandwidth at about 16 kilohertz for a 5 volt swing. A 1 kHz sine wave at 5 volts peak needs 0.03 volts per microsecond and is comfortable. A 20 kHz sine wave at the same amplitude needs 0.63 volts per microsecond and is not.
The reel and the cost case
Five thousand pieces on one reel is a year of production for a board that ships four hundred a month, and it is the quantity that gets the lowest piece price in the family. The tape is 16.4 millimetres wide with a 6.5 by 9.0 millimetre pocket, which is a different carrier from the 12.4 millimetre tape used on the A sort of the same body, so a line that switches between the two sorts has to change the feeder setup even though the part is the same size.
That is the kind of detail that eats a saving. The grade difference is a few cents a part, and a feeder change is a line stop, so the cheaper sort is not cheaper if the board carries both. Our BOM consolidation page covers that arithmetic, and the how to reduce component cost page sets out where the money usually is on a board of this kind.
The replacement route is worth naming too. B versions of this family have a 600 microvolt typical offset, a 3 volt minimum supply, integrated EMI filtering and the same pinout, and they cost less than the plain grade on most quotes. A release that still names this string should be checked against the B part before the next build rather than after the next shortage.
Where the plain sort is chosen
The plain sort wins when the amplifier is doing housekeeping rather than measurement. A reference buffer, a divider follower, a comparator preamplifier, a lamp driver, a fan tachometer shaper. In each of those the signal is large, the threshold margin is wide and the 9 millivolt window over temperature is irrelevant.
It also wins when the board is high volume and the test limits are written against the part rather than the other way round. A line that has been running the plain sort for years has a test program built around its distribution, and changing the grade changes the distribution and the limits together.
Two rows that limit the swing
The first is the output swing at the load the board actually presents. On a 5 volt rail with 2 kilo ohms the output reaches about 3.5 volts, so a 4.5 volt requirement needs a lighter load or a pull up to the rail. The second is the input range at the top end, which stops 1.5 volts below the rail and therefore excludes a high side sense on the same rail.
Both rows are easy to forget because the part is described as single supply and ground sensing, and both are printed in the same table as the offset. A circuit that fails at the top of the swing and not at the bottom is almost always one of these two rows rather than the amplifier itself.
Questions that come with this code
Is 7 millivolts of offset acceptable for a comparator chain? Usually yes, because the comparator's own offset is in the same range and the threshold margin is larger than both.
Why 5000 pieces rather than 2500? The vendor publishes this row at 5000 on a 16.4 millimetre tape, while the A sort is published at 2500 on a 12.4 millimetre tape, so the two sorts do not share a carrier.
Does the part work at 3.3 volts? Yes, the range starts at 3 volts, and the input still includes ground, though the output swing is then limited to about 0.1 to 1.9 volts into a 2 kilo ohm load.
Can it be replaced by a B version? Yes on pinout and function, and the B release should be read for the supply floor and the EMI filter behaviour.