Contact Us

LM211DRG4

Brand: Texas Instruments
Texas Instruments LM211DRG4 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LM211DRG4 — Power Management & Signal Chain | Superb Automation

LM211DRG4

Texas Instruments — Power Management & Signal Chain

Product Overview

The LM211DRG4 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

LM211DRG4: what the G4 suffix changes on the strobed comparator

LM211DRG4 is the single strobed comparator from the LM111, LM211 and LM311 family, ordered under the green material code. The die, the pinout and the electrical rows are the ones the rest of the family carries. The last two characters are the part of the code that a purchaser argues about, and they have nothing to do with the comparator's behaviour.

The family has been in catalogues since 1973 and is still revised, which tells a buyer something useful: the part is not at the end of its life, and the second sources are numerous. A comparator that four or five vendors build to the same pinout is a low risk line item on a bill of materials, and that is the main reason it keeps appearing in new builds.

What follows is the layer of detail that a distributor page does not carry: what the code decodes to, which electrical rows decide a threshold, what the strobe and balance pins demand, and what to write on a purchase order so that the reel that arrives is the reel that was quoted.

Decoding LM211DRG4 one field at a time

LM is the family prefix, 211 is the temperature and input stage grade, D is the SOIC body with eight pins, R is the tape and reel carrier, and G4 is the green material code. The industrial grade body with no letter after the dash is the tube carrier, which is why a prototype order and a production order sometimes quote different strings for the same silicon.

The G4 code marks the lead free, RoHS compliant version of the same body. On this family the lead finish is nickel palladium gold, the moisture sensitivity level is 1 with an unlimited floor life at 260 degrees peak reflow, and the reel is a 330 millimetre reel with a 12.4 millimetre tape width.

Orderable codeLM211DRG4
Channels1
BodySOIC, 8 pins, 4.9 by 3.9 millimetres nominal
Carriertape and reel, 2500 pieces, 330 millimetre reel
Lead finishnickel palladium gold, green material code
Moisture levellevel 1, unlimited floor life at 260 degrees
Temperature windowminus 40 to plus 85 degrees

The electrical rows that decide a threshold

The offset voltage window is the first row anyone reads. At 25 degrees the part is specified at 0.7 millivolts typical and 3 millivolts maximum, and the maximum widens to 4 millivolts over the full temperature range. That is a narrow window for a comparator of this age, and it is the reason the family survived in analogue threshold chains long after faster parts appeared.

Input current is the second row, and it matters more than the offset in high impedance work. Bias current is 75 nanoamps typical and 100 nanoamps maximum, and offset current is 4 nanoamps typical and 10 nanoamps maximum. Across a 100 kilo ohm source those currents produce 7.5 millivolts of drop, which is larger than the offset window itself, so a resistive divider feeding the input has to be scaled with the bias current in mind and not only with the ratio.

Input offset voltage at 25 degrees0.7 millivolts typical, 3 maximum
Input offset voltage over temperature4 millivolts maximum
Input offset current4 nanoamps typical, 10 maximum
Input bias current75 nanoamps typical, 100 maximum
Common mode range on plus or minus 15 voltsminus 14.5 to plus 13 volts
Large signal gain40 volts per millivolt minimum, 200 typical
Response time, low to high output115 nanoseconds typical
Response time, high to low output165 nanoseconds typical

Offset, balance pins and the trim that survives production

The eight pin body brings two balance pins out, and a potentiometer between them with its wiper on the positive rail can move the offset through its window. That trim is a production step, not a laboratory step: it is set once at final test, and on a mature product the potentiometer is usually replaced by two fixed resistors selected from a bin.

Two details decide whether the trim survives. The first is temperature. A trim set at 25 degrees holds only as long as the offset drift is small, and the drift is bounded by the 4 millivolt maximum over temperature rather than by the room temperature number. The second is the trimmer's own temperature coefficient, which on a cheap carbon potentiometer can exceed the drift of the comparator itself.

On a board where the threshold is generated by a reference and a divider rather than by a trimmed offset, the balance pins are simply left open, and the document states that the electrical rows assume the balance and strobe pins are open. Leaving them floating is allowed; tying them somewhere is not.

Strobe: a current sink, never a voltage input

The strobe pin forces the output off, and the document is unusually direct about how to drive it. It needs a current of 3 to 5 milliamps, it must not be shorted to ground, and a resistor from a logic rail is the normal way to supply that current. From a 5 volt rail, 1 kilo ohm gives 5 milliamps and 1.5 kilo ohm gives 3.3 milliamps, both inside the window. A 10 kilo ohm resistor gives half a milliamp and leaves the output in a state the data sheet does not promise.

The reason for the warning is the internal structure: the pin feeds a current mirror rather than a gate, so a hard short to ground pulls an unbounded current through a small device. A board that drives the strobe from an open collector logic gate without a series resistor is a board that will eventually return from the field with a dead comparator.

When the strobe is not used it stays open, and the device behaves as a plain comparator. On a multiplexed threshold chain, the strobe is what lets four comparators share one pull-up node without fighting.

The output stage: 50 volts and 50 milliamps behind an open collector

The output is a floating transistor with both collector and emitter brought out, rated at 50 volts and 50 milliamps. That is what makes the part useful in mixed voltage systems: the collector can sit on a 24 volt rail while the input sits on a 5 volt rail, and the emitter output can drive a load referenced to the negative rail instead of ground.

Saturation voltage is 0.75 volts typical and 1.5 volts maximum at 50 milliamps, so a relay or an optocoupler driven directly from the collector sees a volt of drop at full current. That is acceptable for a 12 volt relay with a 5 volt coil margin, and it is not acceptable for a low headroom load, where a small signal MOSFET is the better switch.

Leakage when the output is off is 0.2 nanoamps at 25 degrees and 0.5 microamps over temperature. On a 100 kilo ohm pull-up that leakage is 50 millivolts in the worst case, which is the number to compare against the input threshold of whatever follows.

Where the reel code matters and where it does not

Nothing in the comparator changes between LM211D, LM211DR and LM211DRG4. What changes is the carrier: a 75 piece tube, a 2500 piece reel, and a 2500 piece reel under the green code. A line that places 2000 pieces a week wants the reel, and a line that builds ten prototypes wants the tube, because a partial reel is not returnable and the feeder setup is not free.

For a customer comparing the green code against the plain code, the difference is the material declaration. The green version carries the nickel palladium gold finish and the level 1 moisture rating, which removes the baking step from the assembly floor. A contract assembler that already bakes every incoming reel will not notice the difference; one that runs a lean line with no bake oven will.

Our power management cross reference page lists the family equivalents that share this pinout, and the date code management page covers how the reel date is recorded when the part is kitted into a build.

Buying questions that come with this code

Is LM211DRG4 different silicon from LM211DR? No. The G4 is a material and finish code, and the electrical rows are identical.

Can the part run from a single 5 volt rail? Yes. The family is specified on a plus or minus 15 volt supply for most rows, and it operates from a single 5 volt rail with the common mode range extending to 1.5 volts below the positive rail. The response time and the offset windows are the ones to re-check in that configuration.

What replaces it if the reel is unavailable? The LM311 in the same body, with a wider 0 to 70 degree window and a looser offset, or a modern part from the same category. Either move changes the offset budget unless the trim is repeated, which is why our pin to pin cross reference page starts with the offset row rather than with the pinout.