ISOW7741FQDFMRQ1
Product Specifications
ISOW7741FQDFMRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The ISOW7741FQDFMRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ISOW7741FQDFMRQ1: the automotive quad isolator with its own isolated supply
The ISOW7741FQDFMRQ1 combines four isolated channels, a low default state and an integrated DC-DC converter in a 20 pin wide body, qualified to AEC-Q100 grade 1 for minus 40 C to plus 125 C ambient. Three channels run forward and one runs back, which is the map a battery management or traction interface usually needs: three commands out to the field and one fault or status line back.
The converter is the reason this part sits in the same body as the channels. On an automotive board, the field side often has no local supply, and a transformer driver plus a discrete transformer costs area, height and a qualification cycle. The integrated converter switches at a low frequency for noise reasons and the vendor states the emissions performance against the automotive CISPR 25 limit rather than the industrial CISPR 32 limit, which is the stricter of the two in the band that matters for a vehicle harness.
The barrier is rated to 5000 VRMS for one minute under UL 1577 with a repetitive peak of 7071 VPK and a working voltage of 1000 VRMS. Data rate is 100 Mbps on the isolated channels, so the part carries a fast sensor bus as easily as a pair of discrete commands.
Key data for the ISOW7741FQDFMRQ1
| Function | Four isolated channels plus an integrated isolated DC-DC converter |
| Direction | Three forward and one reverse, with the low default of the F variant |
| Qualification | AEC-Q100 grade 1, ambient minus 40 C to plus 125 C |
| Data rate | 100 Mbps on the isolated channels |
| Isolation | 5000 VRMS for 60 s per UL 1577, 7071 VPK repetitive peak, 1000 VRMS working voltage |
| Emissions | Stated against the automotive CISPR 25 limit, with ferrite bead provisions on the package |
| External parts | Decoupling on each side and optional beads, no transformer and no external converter |
Body, packing and marking data
| Body | SOIC DFM, 20 pins, wide isolated body |
| Packing | 850 pieces on a large reel on the plain and the A row |
| Finish | NIPDAU, moisture level 3 with a 168 hour floor life, 260 C peak |
| Marking | ISOW7741F printed on the body |
| Temperature | Minus 40 C to plus 125 C ambient, grade 1 |
What grade 1 buys and what it does not
Grade 1 is a temperature and a test flow. It does not by itself prove that the integrated converter meets the conducted emissions limit in a vehicle harness. That has to be measured on the board, in the enclosure, with the real cable length. A vendor statement about a limit is a starting point, not a release criterion.
The other thing grade 1 does not buy is the supply budget. The converter output is smaller than the industrial members of the family in some conditions, and the derating at 125 C is steeper than at 85 C. Add up the isolated loads at the top of the range and compare with the published curve before the part is fixed on the board, and allow for the extra margin that a sealed enclosure removes.
There is also a build question. The package has provisions for ferrite beads, and a board that omits them because the reference board passed on the bench may still fail in the vehicle harness, where the cable length and the nearby loads are different. Populate the footprint on the first build even if the beads are not fitted, so the option stays open without a board spin.
Where a quad isolator with its own supply belongs
Battery management systems use it to cross from the pack controller to the cell monitoring side. Traction inverters use it for gate commands and fault returns. On board chargers use it where the controller sits on a low voltage island and the field side has no supply of its own.
Our CAN bus transceiver selection page covers the pairing of an isolated bus port with a converter, and the supplier quality audit page sets out the evidence an automotive customer asks for when the part is not bought through a franchised channel.
Questions we get on this code
Buyers ask whether the industrial member of the same family can be used in a vehicle when the temperature happens to fit. It should not be. The automotive release carries its own qualification evidence and its own emissions statement, and an audit will ask for the document rather than for the datasheet number.
The second question is about the reel size and the feeder. This body ships 850 pieces per reel, and the carrier is wider than a 16 pin part, so a line change is needed. Plan the reel count and the feeder setup together, because a reel that does not fit the machine stops the line just as effectively as a missing part, and a second setup costs a shift of output on a line that is already quoting a delivery date.